Cordless Cleaner HANDY VAC II MODEL 4071D INSTRUCTION MANUAL SPEC I FICAT10NS Capacity 600 mi ! Dimensions IL x W x H ) Net weight 3 6 5 mm x 102 mm x 108 mm 114 318" x 4" x 4-1/4") 0 6 kg I1 3 Ibs) ~~ * Manufacturer reserves the right t o change specifications without notice * Note Specifications may differ from country t o country
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE WARNINGTO reduce the risk of fire, electric shock, or injury: 1. Do not leave appliance when the battery cartridge is installed. Remove the battery cartridge from your appliance when n o t in use and before servicing. 2. Do not allow t o be used as a toy. Close attention is necessary when used by or near children. 3.
1.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge w h e n temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. 3. Do not allow anything t o cover or clog the charger vents. 4. Always cover the battery terminals with the battery cover when the battery cartridge is not used. 5.
Installing or removing battery cartridge I *Always switch off the tool before insertion or removal of the battery cartridge. Set d a t e / To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing i t from the barrel. To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the set plate back into place.
Switch action To start the tool, simply pull the trigger. Release the trigger to StOD. CAUTION : Before operation, always check to be sure that the filter and pre-filter are correctly installed, or dirt and foreign matter will get into the motor and cause a failure. Cleaning (Suction) Nozzle Attach the nozzle to clean off tables, desks, furniture, etc. Nozzle slips on easily. Nozzle + Extension wand The extension wand fits in between the nozzle and the cleaner itself.
Crevice tool Fit on the crevice tool attachment for cleaning corners and crevice tool of a car or furniture. Sand and other heavy items can be sucked up easily. Crevice tool + Extension wand In tight quarters where the cleaner itself cannot squeeze in, or in high places hard to reach, the extension wand may be used.
Dust disposal Raise the end of the cleaner so that the contents will not fall out. Then tap by hand the side of the capsule 4 or 5 times in order to detach materials from the prefilter and filter and facilitate emptying. Tip end of cleaner (with suction hole) down and unscrew capsule as indicated in arrow direction. Remove capsule carefully keeping it straight up and down so that the contents will not spill out. Empty the contents of the capsule and also the dust adhering to the pre-filter.
Turn the pre-filter and pull it off toward you, emptying out the fine dust inside. Then take out the filter and tap out any adhering dust. After emptying out the cleaner, re-assemble in the order shown in the figure. 1 . Fit filter snugly on all the way. 2. Slip on pre-filter. 3. Screw on the capsule.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. From time to time wipe off the outside (housing) of the cleaner using a cloth dampened in soapy water. Never use gasoline, thinner or the like or discoloration or cracks can take place. Rins out the filter in soapy water occasionally. Dry it out thoroughly before use. I Never use an electric washer t o clean the filter.
ACC ESSOR I ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury t o persons, The accessories or attachments should be used only in the proper and intended manner. Extension wand Part No. 412040-0 0 Nozzle assembly Part No. 122234-6 Nozzle assembly (for carpet) Part No. 122291 - 4 0 Crevice tool Part No. 41 1891 - 8 0 Battery cartridge 7000 Part No.
Jan.-08'87 EN CORDLESS CLEANER Model 4071D Note: The switch and other part configurations may differ from country to country.
9 1 10 11 6 12 13 14 15 16 1 1 1 1 1 1 Hanger Tapping Screw 3 x 2 0 Filter Pm Filter Stop Ring CS Valve Capsule 3 Housing Set I W i t h Item 31 13
The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. I Ni-Cd I To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b). Take the battery to your nearest Makita Authorized Service Center or Distributor that has been designated as a Makita battery recycling location.