ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Brad Nailer GF600 012803 IMPORTANT: Read Before Using.
ENGLISH (Original instructions) SPECIFICATIONS Model GF600 Nail length Nail Gauge 16Ga :15 mm - 65 mm Nail capacity 100 nails (2strip) Dimensions (L X H X W) 266 mm X 90 mm X 304 mm Net weight 2.2 kg Rated voltage D.C. 7.2 V • Due to our continuing program of research and development, the specifications herein are subject to change without notice. • Specifications and battery cartridge may differ from country to country.
• Work area safety 1. Keep work area clean and well lit. Cluttered or dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. 3. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. Electrical safety 4. Power tool plugs must match the outlet. Never modify the plug in any way.
when used with another battery pack. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. 26. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. 27.
For Australia and New Zealand only Always wear safety glasses and face shield to protect your eyes from dust or fastener injury. The safety glasses and the face shield should conform with the requirements of AS/NZS 1336. Do not attempt to keep the contact element depressed with tape or wire. Death or serious injury may occur. • Always check contact element as instructed in this manual. fasteners may be driven accidentally if the safety mechanism is not working correctly.
instruction manual may cause serious personal injury. − when changing one driving location to another involves the use of scaffoldings, stairs, ladders, or ladder alike constructions, e.g. roof laths; − closing boxes or crates; − fitting transportation safety systems e.g. on vehicles and wagons. • Check walls, ceilings, floors, roofing and the like carefully to avoid possible electrical shock, gas leakage, explosions, etc. caused by striking live wires, conduits or gas pipes.
charging it. Overview of the nailer 2 3 012805 To install the battery cartridge, hold it so that the battery cartridge front shape fits to that of the battery installment opening and slip it into place. Insert it all the way until it locks in place with a little click. 1. Button 9 5 4 6 1 8 7 10 1 1. Battery cartridge 2. Fuel cover 3. Trigger 4. Indication lamp 5. Pusher button 6. Pusher lever 7. Magazine 8. Contact element 9. Lamp 10.
Fuel cell 1. Jet nozzle Attaching the metering valve to the fuel cell 1 1. Metering valve 2. Cap 1 012809 2 Insert the fuel cell directing the jet nozzle of the metering valve toward the adaptor. 012807 Detach the cap (in case the metering valve is provided with the cap). 009450 Insert the jet nozzle into the small hole of the adapter properly. 009446 Push in the front edge. 012811 Put the fuel cover over the metering valve and push it down to latch.
it gets stuck. Indication lamp Color of the indication lamp means the followings. Blinking green: Normal status Blinking red: Need to recharge the battery cartridge Lighting-up-red: Recharge the battery cartridge. Nailing cannot be performed due to no remaining battery capacity. Blinking orange after blinking green and red alternately: Fault detection is running. Remove and reinsert the battery cartridge to reset. If fault detection is running again, it is malfunction condition.
1. Nose adapter 1 012817 012894 1. To drive a nail, place the contact element against the workpiece. The fan motor is activated, fuel gas is injected into combustion chamber and mixed with air by the fan. Short nail adapter 1. Short nail adapter 1. Trigger 1 1 012947 1. Short nail adapter 2. Bolt 2 012818 2. Hold the contact element pressing firmly and pull the trigger. Fuel gas is combusted and the nail is driven. 3.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts. Open the latch and release the door, then remove the jammed nail. MAINTENANCE • • Thoroughly cleaning CAUTION: Always remove the fuel cell, the battery cartridge and nails before attempting to perform inspection or maintenance. Never use gasoline, benzine, thinner, alcohol or the like.
Makita Corporation Anjo, Aichi, Japan 885078-228 12 www.makita.