HEDGE TRIMMER EH 450 EH 620 INSTRUCTION MANUAL . WARNING: To reduce the RISK of injury, user must read and understand the instruction manual before using the Hedge Trimmer. . Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. Do only hand over the Hedge Trimmer together with this manual.
Thank you very much for selecting the MAKITA Hedge Trimmer. We are pleased to be able to offer you the MAKITA Hedge Trimmer which is the result of a long development program and many ears of knowledge and experience. The Hedge Trimmer models EH450/620 combines the advantages of state-of-the-art technology with ergonomic design, they are light weight, handy, compact and represent professional equipment for a great variety of applications.
General Instructions - This machine can c a u s e serious injuries if used incorrectly. - - TO ensure correct operation, users have to read this instruction manual to make themselves familliar with the handling of the Hedge Trimmer. Users insufficiently informed will risk danger to themselves as well as others d u e to improper handling. (1) It is recommended only to loan the Hedge Trimmer to people who have proven to b e experienced with Hedge Trimmers. Always hand over the instruction manual.
Starting up the Hedge Trimmer Please make sure that there are children or other people within a working range of 50 feet or 15 meters (5),also pay attention to any - animals in the working vicinity Before operating, always c h e c k that t h e Hedge Trimmer is s a f e for operation: Check the security of the throttle lever. The throttle lever should be checked for smooth and easy action. Check for proper functioning of the throttle lever lock.
Method of operation - Use the Hedge Trimmer only in good light and visibility. During cold s e a s o n s beware of slippery or wet areas, ice and snow (risk of slipping). Always ensure a safe footing. Do not overreach or stand on unstable support. Keep good footing and balance a t all times. - Keep both feet on the ground. - Never stand on a ladder and the Hedge Trimmer. - Never climb up into trees to perform cutting operation with the Hedge Trimmer. - DANGER-CUT HAZAARD-KEEP HANDS AWAY FROM BLADES.
First aid In case of a n accident make sure that a well-stocked first-aid kit according to DIN 13164, is available in the vicinitv of the cuttina operations. Immediately replace any item taken from the first aid kit. - I Packaging The MAKITA Hedge Trimmer is delivered in a protective cardboard box to prevent shipping damage. Cardboard is.a basic raw material and is therefore consequently reusable or suitable for recycling (waste paper recycling).
NAME OF MAJOR PARTS EH450 EH620 NAME OF MAJOR PARTS NAME OF MAJOR PARTS 1 Blade 7 Throttle lever 2 Front handle 8 Rear handle 3 Recoil starter 9 Muffler Fuel tank cap 10 Gearbox 5 Carburetor 11 Blade cover 6 STOP Switch (ON-OFF) 4 ..
FUELSIREFUELLING Fuel and oil mirture Inspect the fuel tank and fill with clean, fresh fuel of the proper mixture to assure the longer life of the tool. Use the following mixed gas.
Refuelling Always stop the engine and allow it to cool before refuelling. - Thoroughly clean the around the fuel filler cap to prevent dirt from getting into the fuel tank. - Unscrew the fuel filler c a p and fill the tank with fuel. - Tightly screw on the fuel filler cap. - Clean the fuel filler c a p and tank after refuelling! Wipe up any fuel Storage of fuel - Fuel cannot be stored for a n unlimited period of time. - Purchase only the quantity required for a 4 week operation period.
STARTING THE MACHINE Move a t least 3 meters away from the place of refuelling. Place the Hedge Trimmer on a clean a r e a of ground make sure that the cutting tool d o e s not c o m e into contact with the ground or any other objects. Cold starting (When t h e engine is cold or it h a s been stopped for more than 5 minutes or when fuel is added to the engine. 1. Push the STOP switch (1) to "I" position. 2. Squeeze first the lock lever A and then the throttle lever B. (fig.1) 3.
OPERATION OF THE MACHINE - Be sure to carefully read and follow safety instructions. - Keep hands away from blades. Never grasp the exposed cutting blade or cutting edges, when picking up or holding the tool. - Never touch the cutting device when starting the engine and - - - - - - during operation. Operate the Hedge Trimmer in such a manner as to avoid inhalation of the exhaust gases. Never run the engine in enclosed rooms (Risk of g a s poisoning). Carbon monoxide is a n odorless gas.
MAINTENANCE INSTRUCTIONS - - Turn off the engine and remove the spark plug connector when replacing or sharpening cutting tools, also when cleaning the cutter or cutting device or carrying out any maintenance. Never straighten or weld a damaged cutting blade. Inspect the cutting blades with the engine switched off at short, regular intervals for damage. (Detection of hairline cracks by means of tapping-noise test.) Beware the teeth are sharp.
Checking and adjusting t h e idling s p e e d The cutting blade should not when the control lever is fully released. - Idle speed should be s e t to 2,600 rpm. If necessary, correct it by means of the idle screw (the cutting blade must not run when the engine is on idle).
- Suction head in the fuel tank Every 50 hours (Monthly) The felt filter (1) of the suction head is used to filter the fuel - - required by the carburetor. A periodical visual inspection of the felt filter is to be conducted. For that purpose, open the tank cap, u s e a wire hook and pull out the suction head through the tank opening. Filters found to have hardened, been polluted or clogged up are to be replaced. Insufficientfuel supply can result in the admissible maximum speed being exceeded.
STORAGE n I - When keeping the machine in storage for a long,time, drain fuel from the fuel tank and carburetor, as follows: Drain all fuel from the fuel tank. - Remove the spark plug and add a few drops of oil into the spark plug hole. Then, pull the starter gently to confirm that oil film covers the engine inside and tighten the spark plug. - Clear dirt or dust from the cutter blade and outside of engine, wipe them with a oil-immersed cloth and keep the machine a t a place as dry as possible.
California Emission Control Warranty Statement [This warranty d o e s not apply in any other state.] YOUR WARRANTY RIGHTS AND OBLIGATIONS The CaliforniaAir Resources Board and Makita U.S.A., Inc. are pleased to explain the emission control warranty on your 7995 and later utility and/or lawn and garden equipment engine. In California,new utility and lawn and garden equipment engine must be designed, built and equipped to meet the State’s stringent anti-smog standards. Makita U.S.A., Inc.
LIMITED WARRANTY California Only - - Makita U.S.A., Inc. a distributor of utility and lawn and garden equipment in the U.S.
WHAT IS NOT COVERED UNDER THIS WARRANTY This warranty does not cover any emission-related part which malfunctions, fails, or is damaged d u e to alterations and/or modifications such as changing, adding, or removing parts. When a n engine is being serviced under warranty, Makita U.S.A., Inc. and a n y of its authorized dealers, distributors, or warranty stations shall not be liable for any loss of u s e of the engine, for any damage to goods, or loss of time or inconvenience.
REPAIR AND REPLACEMENT OF EMISSION-RELATED PARTS It is recommended that only engine replacement parts which have been authorized a n d approved by Makita U.S.A., Inc. should be used in the performance of any warranty maintenance or repairs of emission-related parts. T h e s e replacement parts will b e provided a t no charge if the part is still under warranty.
FEDERAL EMISSION COMPONENT DEFECT WARRANTY EMISSION COMPONENT DEFECT WARRANTY COVERAGE - This emission warranty is applicable in all States, except the State of California Makita U.S.A., Inc., La Mirada, California, (herein “MAKITA) warrant to the initial retail purchaser and each subsequent owner, that this utility equipment engine (herein “engine”) w a s designed, built, and equipped to conform at the time of initial sale to all applicable regulations of the U.S.
OBTAl N I NG WARRANTY SERVICE To obtain warranty service, take your engine to the nearest Makita Factory Service Center or Service Center authorized by MAKITA. Bring your sales receipts indicating date of purchase for this engine. The dealer or service center authorized by MAKITA will perform the necessary repairs or adjustments within a reasonable amount of time and furnish you with a copy of the repair order. All parts and accessories replaced under this warranty become the property of MAKITA.
THINGS YOU SHOULD KNOW ABOUT THE EMISSION CONTROLL SYSTEM WARRANTY MAINTENANCE AND REPAIRS You are responsible for the proper use and maintenance of the engine. You should keep all receipts and maintenance records covering the performance of regular maintenance in the event questions arise. T h e s e receipts and maintenance records should b e transferred to each subsequent owner of the engine. MAKITA reserves the rights to deny warranty coverage if the engine h a s not been properly maintained.
MEMO ..................................................................................................................................................................... ...................................................................................................................................................... ..... ............ ..................................................................................................................................................................... ..
A WARNING: The Engine Exhaust from this product contains chemicals known to the state of California to c a u s e cancer, birth defects or other reproductive harm. Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502, Japan 5199501700 99.