ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Grass Trimmer DUR142L DUR182L DUR183L 014149 IMPORTANT: Read Before Using.
ENGLISH (Original instructions) SPECIFICATIONS Model DUR142L Type of pipe DUR182L DUR183L Integrated pipe Splittable pipe 3,500 - 6,000 min-1 No load speed Overall length with nylon cutting head 1,843 mm Split length - Cutting diameter with nylon cutting head 982 mm 300 mm Net weight 3.8 kg Rated voltage D.C. 14.4 V D.C.
Cd Ni-MH Li-ion 31.12.2013 ・ Do not expose to moisture. ・ Top permissible tool speed. ・ Never use metal blade.
12. 13. 4. Never operate the tool when tired, feeling ill or under the influence of alcohol or drugs. The tool should be switched off immediately if it shows any signs of unusual operation. Intended use of the tool 1. Use right tool. The cordless grass trimmer is only intended for cutting grass, light weeds. It should not be used for any other purpose such as hedge cutting as this may cause injury. 5. Personal protective equipment 6. 7.
. 17. Before starting make sure that the cutting tool has no contact with hard objects such as branches, stones etc. as the cutting tool will revolve when starting. Maintenance instructions Method of operation 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Don't force the tool. It will do the job better and with less likelihood of a risk of injury at the rate for which it was designed. 1. Never operate the machine with damaged guards or without the guards in place.
4. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight. 5. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. 6.
PARTS DESCRIPTION DUR142L DUR182L DUR183L 1 1 2 2 3 3 5 5 4 7 6 4 7 6 8 8 12 12 10 10 9 9 13 11 11 8 Switch trigger Speed adjusting dial 9 Guard Indication lamp 10 Wire guard 4 Power button 11 Cutting tool 5 Lock-off lever 12 Shoulder harness 6 Hanger (suspension point) 13 Cap 7 Grip 1 Battery cartridge 2 3 014160 7
Power switch action FUNCTIONAL DESCRIPTION • WARNING: Always be sure that the tool is switched off and battery cartridge is removed before adjusting or checking the functions on the tool. Failure to switch off and remove the battery cartridge may result in serious personal injury from accidental start-up.
1 B 3 A 2 Battery protection system (Lithium-ion battery with star marking) 1. Reversing switch 2. A position depressed for normal operation 3. B position depressed for weed and debris removal 1 1. Star marking 014159 This tool has a reversing switch which is only provided to change the direction of rotation so that it can be used to remove weeds and debris entangled in the tool. To operate the tool normally the "A" side of the switch should be depressed.
Indication lamps 1. Battery indicator 2. Power indicator 1 2 013836 When the protection system works during the operation, the lamps light up. Refer to the following table for the status and action to be taken for the indication lamp. Power indicator Battery indicator Action to be taken Status Blinking Battery power has been nearly used up. Replace the battery with fully charged one. Lighting Up Battery protector is shutting off the power battery power has been used up.
Mounting the attachment pipe Installing the guard Only for model DUR183L 1 2 3 4 5 1. Joint 2. Lock lever 3. Joint cover 4. Lever 5. Pipe (Cutting tool side) • WARNING: Never use the tool without the guard illustrated in place. Failure to do so can cause serious personal injury. 013831 To mount the attachment to a power unit: 1. Make sure that the lever is not tightened. 2. To open the entrance of the joint, depress the joint cover. 013813 1. Grooves 2. Protector 1. Lock lever 2.
Installing the wire guard • Installing nylon cutting head NOTICE: • Be sure to use genuine Makita nylon cutting head. Turn the tool upside down so that you can replace the nylon cutting head easily. CAUTION: Before adjusting the wire guard, wait for the cutting head comes to standstill. Do not adjust the wire guard with your foot. 1. Nylon cutting head 2. Metal guard 3. Receive washer 4.
Only for model DUR183L MAINTENANCE 1. Cap WARNING: Always be sure that the tool is switched off and battery cartridge is removed before attempting to perform inspection or maintenance on the tool. Failure to switch off and remove the battery cartridge may result in serious personal injury from accidental start-up. NOTICE: Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result. • 1 014165 When the cap is not in use, hang it on the hook. Detachment 1.
Align the protrusion on the underside of the cover with the slots of the eyelets. Then push the cover firmly onto the housing to secure it. Make sure the latches fully spread in the cover. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts.
TROUBLE SHOOTING Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replacement parts for repairs. Malfunction status Motor does not run. Motor stops running after a little use. It does not reach maximum RPM.
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
Makita Jan-Baptist Vinkstraat 2, 3070, Belgium Makita Corporation Anjo, Aichi, Japan 885230A228 www.makita.