ENGLISH: Original instructions INSTRUCTION MANUAL Cordless Blower DUB363 Read before use.
SPECIFICATIONS Model: DUB363 Capacities 0 - 13.4 m3/min Air volume Air speed (average) 0 - 54 m/s Air speed (max.) 0 - 65 m/s Dimensions (L x W x H) *1 341 mm x 193 mm x 415 mm Rated voltage D.C. 36 V Net weight Blower *2 3.8 - 5.2 kg Vacuum *3 6.0 - 6.6 kg *1. Without pipes, nozzles, dust bag, shoulder strap, and battery cartridges. *2. With blower pipe, end nozzle and flat nozzle, and without suction pipe, suction nozzle, elbow pipe, dust bag and shoulder strap. *3.
Preparation 1. Always wear substantial footwear and long trousers while operating the machine. 2. Do not wear loose clothing or jewellery that can be drawn into the air inlet. Keep long hair away from the air inlets. 3. Always wear protective goggles to protect your eyes from injury when using power tools. The goggles must comply with ANSI Z87.1 in the USA, EN 166 in Europe, or AS/NZS 1336 in Australia/New Zealand.
8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. Battery tool use and care 1. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. 2. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. 3.
Tips for maintaining maximum battery life Important safety instructions for battery cartridge 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. Do not disassemble battery cartridge. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.
Installing or removing flat nozzle or extension nozzle 2. Align the protrusion on the blower pipe with the groove on the end nozzle, then attach the end nozzle to the blower pipe, and then turn the end nozzle to lock it into place. Optional accessory Attach the flat nozzle or extension nozzle to the end nozzle, and then turn it to lock it into place. 1 3 2 2 1 ► 1 . End nozzle 2. Blower pipe To remove the blower pipe and end nozzle, perform the installation procedure in reverse.
Attaching shoulder strap Assembly for vacuuming CAUTION: Be sure to attach the hooks of the shoulder strap to the machine securely. If the hooks are attached incompletely, they may come off and cause an injury. Installing or removing suction pipe and nozzle Optional accessory Align the triangle mark on the suction nozzle with that 1. on the suction pipe, and then insert the suction nozzle into the suction pipe until the latch on the nozzle snaps into place.
Installing or removing elbow pipe and dust bag 4. Turn the suction pipe clockwise so that the bolt on the pipe is aligned with the hole on the main unit, and then fasten the bolt firmly using the hex wrench to secure the pipe to the main unit. Optional accessory 1. Insert the elbow pipe into the dust bag and tighten the belt to fix the elbow pipe as shown in the figure. 1 1 2 3 2 ► 1 . Suction pipe 2. Bolt ► 1 . Dust bag 2. Elbow pipe 3.
3. Attach the hook of the dust bag to the shoulder strap, and then attach the hooks of the shoulder strap to the main unit as shown in the figure. 1 2 1 3 ► 1 . Red indicator 2. Button 3. Battery cartridge 1 To remove the battery cartridge, slide it from the machine while sliding the button on the front of the cartridge. To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place.
NOTE: Depending on the conditions of use and the ambient temperature, the indication may differ slightly from the actual capacity. Machine/battery protection system The machine is equipped with a machine/battery protection system. This system automatically cuts off power to the motor to extend machine and battery life.
Cruise control function The cruise control function allows the operator to maintain a constant speed without pulling the trigger. To increase the speed, turn the control lever forward. To decrease the speed, turn the control lever backward. OPERATION CAUTION: Do not place the machine on the ground while it is switched on. Sand or dust may enter from suction inlet and cause a malfunction or personal injury.
1. Put the shoulder strap and dust bag on the shoulder as shown in the figure. Adjust the length of the strap. MAINTENANCE CAUTION: Always be sure that the machine is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. 1 To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
TROUBLESHOOTING Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to dismantle the machine. Instead, ask Makita Authorized Service Centers, always using Makita replacement parts for repairs. State of abnormality Probable cause (malfunction) Remedy Motor does not run. Battery cartridge is not installed. Install the battery cartridge. Battery problem (under voltage) Recharge the battery.
Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan www.makita.
