ENGLISH: Original instructions INSTRUCTION MANUAL Cordless Multi Tool DTM52 Read before use.
SPECIFICATIONS Model: DTM52 10,000 - 20,000 min-1 Oscillation per minute Oscillation angle, left/right Overall length 1.8° (3.6° total) with BL1820B 305 mm with BL1860B 322 mm Net weight 1.7 - 2.0 kg Rated voltage • • • D.C. 18 V Due to our continuing program of research and development, the specifications herein are subject to change without notice. Specifications may differ from country to country. The weight may differ depending on the attachment(s), including the battery cartridge.
The typical A-weighted noise level determined according to EN62841-1: Work mode: Cutting with segmental saw blade Sound pressure level (LpA) : 76 dB(A) Uncertainty (K) : 3 dB(A) WARNING: The vibration emission during actual use of the power tool can differ from the declared value(s) depending on the ways in which the tool is used especially what kind of workpiece is processed. The noise level under working may exceed 80 dB (A).
. 5. 6. 7. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply.
Battery tool use and care 1. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. 2. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. 3.
24. 25. 26. 27. Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock. Always be sure that the tool is switched off and unplugged or that the battery cartridge is removed before carrying out any work on the tool. Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations.
Overload alert function FUNCTIONAL DESCRIPTION The overload alert function may work if the current rises sharply due to the operation such as applying too much pressure onto a workpiece. The overload alert function decline the speed of the oscillation and then increases the amplitude of vibration. In this case, once isolate the application tool from the workpiece, then the speed of the oscillation goes back. Continue operation with an appropriate load.
Adjusting the orbital stroke rate Electronic function The tool is equipped with the electronic functions for easy operation. Constant speed control The speed control function provides the constant orbital stroke rate regardless of load conditions. Soft start feature Soft start feature reduces starting reaction. 1 Accidental re-start preventive function ► 1 . Dial When installing the battery cartridge while the slide switch in the "I (ON)" position, the tool does not start.
1. Open the lock lever fully until it sounds a click. Remove the holder bolt. CAUTION: Always install the battery cartridge fully until the red indicator cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. When the lock lever is fully opened, the position of the lock lever is maintained even if you release your hand. CAUTION: Do not install the battery cartridge forcibly.
3. Return the lock lever to its original position. OPERATION Always make sure that the application tool is securely held in place. WARNING: Before starting the tool and during operation, keep your hand and face away from the application tool. CAUTION: Do not apply excessive load to the tool which may cause a motor lock and stop the tool. CAUTION: Do not operate the tool with pressing the battery cartridge against the tool.
4. Connect the hose of the vacuum cleaner to the dust extraction attachment. Apply a sanding paper on the workpiece. NOTE: Before the operation, it is recommended to determine a suitable orbital stroke rate by sanding a test material sample as trial. Removing the dust attachment 1. When removing the dust attachment, remove the holder bolt and the sanding pad. NOTE: It is recommended not to change the grid of the sanding paper until you finish sanding the whole surface of the workpiece.
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.