ENGLISH: Original instructions INSTRUCTION MANUAL Cordless Pin Nailer DPT353 Read before use.
SPECIFICATIONS Model: DPT353 Pin nail size ø0.6 mm x 15, 18, 25, 30, 35 mm Pin nail magazine capacity 100 pcs. Dimensions without hook (L x W x H) 257 mm x 79 mm x 226 mm Rated voltage D.C. 18 V Battery cartridge BL1815, BL1815N, BL1820, BL1820B BL1830, BL1830B, BL1840, BL1840B, BL1850, BL1850B, BL1860B 2.0 kg 2.2 kg Net weight • • • Due to our continuing program of research and development, the specifications herein are subject to change without notice.
Work area safety 1. Keep work area clean and well lit. Cluttered or dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. 3. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 6. 7. Electrical Safety 1. Power tool plugs must match the outlet. Never modify the plug in any way.
Service 1. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. 2. Follow instruction for lubricating and changing accessories. 3. Keep handles dry, clean and free from oil and grease. • 14. 15. 16. Cordless nailer safety warnings 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Always assume that the tool contains fasteners.
6. 7. 8. 9. 10. 11. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50 °C (122 °F). Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. Be careful not to drop or strike battery. Do not use a damaged battery.
Overload protection Indicator lamps When the tool/battery is operated in a manner that causes it to draw an abnormally high current, the tool automatically stops without any indication. In this situation, turn the tool off and stop the application that caused the tool to become overloaded. Then turn the tool on to restart. Lighted Off Remaining capacity Blinking Charge the battery. The battery may have malfunctioned.
Trigger-lock button 1 CAUTION: Before installing the battery car- B A tridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. CAUTION: When not operating the tool, depress the trigger-lock button from B side to lock the switch trigger in the OFF position. 1 ► 1. Adjuster 1 2 3 2 ► 1. Trigger-lock button 2. Switch trigger ► 1. Too deep 2. Flush 3.
4. After loading pin nails, push back the magazine in place until it clicks. ASSEMBLY To remove pin nails, follow the installation procedures in reverse. CAUTION: Always make sure that your fingers are not placed on the switch trigger or the contact element and the battery cartridge is removed before carrying out any work on the pin nailer.
Test safety systems for possible fault before operation as follows. 1. Unload pin nails from the tool and keep the magazine opened. 2. Install the battery cartridge and release the trigger lock. 3. Only pull the switch trigger without touching the contact element against the material. 1 4. Only touch the contact element against the material without pulling the switch trigger. 2 If the tool operates in the case of 3 and 4 above, the safety systems are faulty.
Removing jammed pin nails WARNING: Always make sure that the battery cartridge is removed before removing jammed pin nails. Take out pin nails that remain inside the magazine. Remove three screws with the hex wrench that are securing the driver guide cover. Take the jammed nails from the nail guide groove that has appeared. When it is difficult to take out the jammed nails, further remove two screws with the hex wrench that are securing the contact top cover. Then take them out.
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan www.makita.