ENGLISH: Original instructions INSTRUCTION MANUAL Cordless Lawn Mower DLM460 DLM461 Read before use.
SPECIFICATIONS Model: DLM460 Mowing width (blade diameter) 2,500 min-1 No load speed 3,300 min-1 Maximum speed Part number of replacement mower blade Dimensions (L x W x H) 199367-2 L: 1,319 mm to 1,518 mm W: 532 mm H: 879 mm to 1,138 mm when stored (without grass basket) L: 1,004 mm to 1,125 mm W: 532 mm H: 533 mm to 713 mm D.C. 36 V Net weight 25.3 - 27.6 kg Protection degree • • 199368-0 during operation Rated voltage • DLM461 460 mm 26.6 - 28.
7. Vibration The vibration total value (tri-axial vector sum) determined according to EN60335-2-77: Model DLM460 Vibration emission (ah) : 2.5 m/s2 or less Uncertainty (K) : 1.5 m/s2 Always wear protective goggles to protect your eyes from injury when using power tools. The goggles must comply with ANSI Z87.1 in the USA, EN 166 in Europe, or AS/NZS 1336 in Australia/New Zealand. In Australia/New Zealand, it is legally required to wear a face shield to protect your face, too.
16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. Keep hands and feet away from rotating blades. Caution - Blades coast after the mower is switched off. Use only the manufacturer genuine blades specified in this manual. Check the blades or blade bolts carefully for cracks or damage before operation. Replace cracked or damaged blades or blade bolts immediately. Be sure the area is clear of other people before mowing. Stop mower if anyone enters the area.
4. 55. 56. 57. 58. 59. 60. 61. 62. When washing the machine, be sure to remove the battery and lock key and close the battery cover, and pour water toward the bottom of the machine to which the blade is attached. When storing the machine, avoid direct sunlight and rain, and store it in a place where it does not get hot or humid. Perform inspection or maintenance in a place where rain can be avoided. After using the machine, remove the adhered dirt and dry the machine completely before storing.
2. Align the hole in the lower handle with the hole in the upper handle, then insert the bolts from inside, then attach washer B from outside, and then tighten the thumb nuts. ASSEMBLY WARNING: Always be sure that the lock key and battery cartridge are removed before carrying out any work on the mower. Failure to remove the lock key and the battery cartridge may result in serious personal injury from accidental start-up. 1 6 WARNING: Never start the mower unless it is completely assembled.
2. Removing the mulching attachment Remove the mulching attachment while pulling the lever. For DLM460 1. 1 Open the rear cover. 1 2 ► 1. Rear cover ► 1. Mulching attachment 2. Lever 2. Remove the mulching attachment while holding down the lever. Installing the grass basket 1. Open the rear cover. 1 1 2 ► 1. Lever 2. Mulching attachment For DLM461 1. ► 1. Rear cover Open the rear cover. 2. Hook the grass basket on the rod of the mower body as shown in the figure.
2. Attach the mulching attachment while pulling the lever, and then release the lever to lock the mulching attachment. Attaching the mulching attachment For DLM460 1. Open the rear cover, and then remove the grass basket. 1 1 2 ► 1. Rear cover 2. Grass basket 2 2. Attach the mulching attachment while holding down the lever, and then release the lever to lock the mulching attachment. ► 1. Mulching attachment 2.
To install the battery cartridge; 1. Tool / battery protection system Pull up the locking lever, and then open the battery cover. The tool is equipped with a tool/battery protection system. This system automatically cuts off power to the motor to extend tool and battery life.
Indicator lamps Lighted Off Main power switch Remaining capacity WARNING: Always turn off the main power switch when not in use. Blinking 75% to 100% To turn on the machine, press the main power switch. The main power lamp lights up in green. To turn off the machine, press the main power switch again. 50% to 75% NOTE: If the main power lamp lights up in red or blinks in red or green, refer to the instructions for tool/ battery protection system. 25% to 50% 0% to 25% Charge the battery.
Switch action Adjusting the mowing height WARNING: Before installing the battery cartridge, always check to see that the switch lever actuates properly and returns to the original position when released. Operating a tool with a switch that does not actuate properly can lead to loss of control and serious personal injury. WARNING: Never put your hand or leg under the mower body when adjusting the mowing height. WARNING: Always make sure that the lever fits in the groove properly before operation.
Adjusting the handle height OPERATION CAUTION: Before removing the bolts, hold the upper handle firmly. Otherwise, the handle may fall and cause an injury. Mowing WARNING: Before mowing, clear away sticks and stones from mowing area. Furthermore, clear away any weeds from mowing area in advance. The handle height can be adjusted in three levels. 1. Loosen the thumb nuts of the lower handle, and then remove the bolts, washer, and thumb nuts.
1 NOTE: Mowing long grass to a short length all at once may cause the grass to die. The cut grass may also block up inside of the mower body. 2 Emptying the grass basket 3 WARNING: To reduce a risk of accident, regularly check the grass basket for any damage or weakened strength. Replace the grass basket if necessary. 3 1. Release the switch lever. 2. Remove the lock key. 3. Open the rear cover and take out the grass basket by holding the handle. ► 1. Mowing width 2. Overlapping area 3.
2. Maintenance Loosen the thumb nuts and fold the upper handle. 1. Remove the lock key and battery cartridges, and then close the battery cover. 1 2. Put the mower on its side and clean grass clippings accumulated on the underside of mower deck. 3. Pour water toward the bottom of the machine to which the blade is attached. 2 NOTICE: Do not wash the machine with high pressure water. 4. Check all nuts, bolts, knobs, screws, fasteners etc. for tightness. 2 5.
3. 3. Turn the bolt counterclockwise with the wrench. Remove the bolt, washer, base plate in order. 1 2 3 1 ► 1. Mower blade 2. Wrench 3. Lumber 4. Remove the bolt, washer, mower blade in order. 2 3 ► 1. Base plate 2. Washer 3. Bolt 1 4. To remove the individual blade, turn the bolt counterclockwise with the wrench while holding the base plate. 2 3 1 ► 1. Mower blade 2. Washer 3. Bolt 2 For DLM461 1.
For DLM461 NOTICE: When installing the mower blade, slide the mower blade as shown in the figure so that the protrusions touch the mower blade. 1 2 ► 1. Protrusion 2. Mower blade TROUBLESHOOTING Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replacement parts for repairs.
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan www.makita.
