Owner’s and Safety Manual for Gasoline Chain Saws (page 2 - 33) Manuel d’emploi et de sécurité de tronçonneuses thermiques (page 34 - 65) DCS 34 WARNING! Read and understand this Manual. Always follow safety precautions in the Owner’s and Safety Manual. Improper use can cause serious injury! The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
WARNING ! Careless or improper use of this product can cause serious or even fatal injury. Before operating a chain saw or other MAKITA products it is important that you read, fully understand and carefully follow the instructions outlined in this owners manual. Kickback may cause severe or fatal injury and is one of many potential dangers in operating a chain saw. Kickback and other safety related precautions are described in detail within this owners manual.
Delivery inventory 2 3 4 5 1. Chain saw 2. Guide bar 3. Saw chain 4. Chain protection cover 5. Assembly tool 6. Owner’s and Safety Manual (not shown) 1 In case one of the parts listed should not be included in the delivery inventory, please consult your sales agent.
Safety precautions for chain saw operators Additional safety precautions While operating the chain saw please observe the following rules: a) Contact of the guide bar nose with any object should be avoided. b) Tip contact may cause the guide bar to move suddenly upward and backward, which may cause serious or fatal injury. c) Always operate the chain saw with both hands. The following additional safety precautions should be observed by all users of chain saws: 1.
General Safety Precautions max. CKA 21O The use of any chain saw may be hazardous. At full throttle chain speed can reach 45 mph (20 m/s). It is important that you read; fully understand and observe the following safety precautions and warnings. Read the owner’s manual and the safety instructions periodically. Maximum Computed Kickback Angle (CKA)* without using the chain brake when using the recommended bar and chain combinations (In this example the CKA is 21°).
The saw Proper clothing Clothing must be sturdy and snug-fitting, but allow complete freedom of movement. Avoid loose-fitting jackets, scarfs, neckties, jewelry, flared or cuffed pants, or anything that could become entangled with the saw or brush. Wear overalls or jeans with a reinforced cutting resistant insert (fig. 3). Protect your hands with gloves when handling saw and saw chain. Heavy-duty, nonslip gloves improve your grip and protect your hands. Good footing is most important in chain saw work.
Chain saw operating instructions For assembly follow the procedure in the appropriate section "Mounting Guide Bar and Chain" of this manual. MAKITA chain, guide bar and sprocket must match each other (see the appropriate section in this manual). WARNING! Proper tension of the chain is extremely important. In order to avoid false setting the tensioning procedure must be followed as described in this manual.
Important adjustments WARNING! At correct idle speed, chain should not turn. For directions to adjust idle speed, see the appropriate section of this instruction manual. Do not use a saw with incorrect idle speed adjustment. Adjust the idle speed yourself according to the appropriate section of this manual. Wrap your fingers tightly around the handles, keeping the handles cradled between your thumb and forefinger (fig. 7).
In order to keep control of your saw, always maintain a firm foothold. Never work on a ladder, in a tree or on any other insecure support. Never use the saw above shoulder height (fig. 9). 10 Position the chain saw in such a way that your body is clear of the cutting attachment whenever the engine is running (fig. 10). Don’t put pressure on the saw when reaching the end of a cut.
Many factors influence the occurence and force of the kickback reaction. The type of bar and saw chain you use is a factor in the force of the kickback reaction. The speed of contact at which the cutter contacts the object. Kickback force increase with the rate of impact. The contact angle between the nose of the bar and the foreign object (fig. 11). Kickback is most pronounced in the upper quadrant of the bar nose. MAKITA chain types are designed to reduce kickback forces.
Pushback: To avoid pull-in Pushback occurs when the chain on the top of the bar is suddenly stopped when it is pinched, caught or encounters a foreign object in the wood. The reaction of the chain drives the saw straight back toward the operator causing loss of saw control. Pushback frequently occurs when the top of the bar is used for cutting (fig. 14). 1. Always start a cut with the chain rotating at full speed and the spike bar in contact with the wood. 2.
45° 2 12 First cut 45° Second cut = cutting down area 20 17 When felling, maintain a distance of at least 2 1/2 tree lengths from the nearest person (see fig. 17). If the tree has large buttress roots, cut into the largest buttresses vertically first (horizontally next) and remove (fig. 20). Note: The noise of your engine may drown any warning call.
Begin the felling cut slighty higher than the felling notch and on the opposite side of the tree (fig. 22). Then cut horizontally through towards the felling notch. Apply the chain saw with its spikes directly behind the uncut portion of wood and cut toward the notch (fig. 23). Leave approximately 1/10 of the tree diameter uncut! This is the hinge (fig. 23). Do not cut through the hinge because you could lose control of the direction of the fall.
Bucking 3 Bucking is cutting a log into sections. 2 1 29 WARNING! There is an extreme danger of kickback at this point. Extra caution must be taken to maintain control of the saw. To make the felling cut, follow the sectioning method described previously (fig. 29). If you are inexperienced with a chain saw plunge-cutting should not be attempted. Seek the help of a professional. 31 WARNING! 1. When bucking, do not stand on the log. Make sure the log will not roll down-hill.
Maintenance and Repair Never operate a chain saw that is damaged, improperly adjusted or not completely or securely assembled. Follow the maintenance and repair instructions in the appropriate section of this manual. 1. Relieving cut Pressure side Tension side 2. Cross cut WARNING ! 33 2. Cross cut Always stop the engine and make sure that the chain is stopped before commencing any maintenance or repair work or cleaning the saw.
Denomination of components 1 2 3 4 5 9 7 6 8 24 25 10 11 12 13 14 15 23 22 21 Identification plate 20 19 18 17 16 Year of manufacture DCS 34 9905 123456 528.092.656 442.040.661 16" inch (40 cm) Serial number Indicate when ordering spare parts! 22045 Hamburg, Germany 036.100.
Technical data DCS 34 Single-cylinder two-stroke Piston displacement Cylinder bore Piston stroke Max. power at speed Max. torque at speed Idling speed Sound Pressure Level at the operator’s ear at full load according to ANSI B 175.1 Sound Pressure Level at the bystander’s position (50ft/15 m distance) according to ANSI B 175.1 Ignition system Electronic, without breaker Spark plug or Spark plug Electrode gap 2.0 cu. in (33 cm3) 1.45" (37 mm) 1.22" (31 mm) 1.3/9,000 kW/rpm 1.
PUTTING INTO OPERATION CAUTION: Before doing any work on the guide bar or chain, always switch off the engine and pull the plug cap off the spark plug (see "Replacing the spark plug"). Always wear protective gloves! STOP CAUTION: Start the chain saw only after having assembled it completely and inspected! A Mounting the guide bar and saw chain Use the universal wrench delivered with the chain saw for the following work.
11 Lift the chain (8) over the sprocket (9). Using your right hand, guide the chain into the top guide groove (10) on the guide bar. The cutting edges along the top of the chain must point in the direction of the arrow (11)! 8 9 E 10 8 12 Pull the chain (8) around the sprocket nose (12) of the guide bar in the direction of the arrow. F 2 Replace the sprocket guard (3), putting the chain (8) over the chain catcher (13). Manually tighten the retaining nuts (2).
Checking the chain tension STOP The tension of the chain is correct if the chain rests against the bottom side of the guide bar and can still be easily turned by hand. While doing so the chain brake must be released. Check the chain tension frequently - new chains tend to get longer during use! When checking the chain tension the engine must be switched off. NOTE: It is recommended to use 2-3 chains alternatively.
Fuel CAUTION: This saw is powered by mineral-oil products (gasoline (petrol) and oil). Be especially careful when handling gasoline (petrol). Avoid all flame or fire. Do not smoke (explosion hazard). Fuel mixture Gasoline The engine of the chain saw is a high-efficiency two-stroke engine. It runs on a mixture of gasoline and two-stroke engine oil. The engine is designed for unleaded regular gasoline with a min. octane value of 91 ROZ.
Important note on bio-degradable chain oils: If you are not planning to use the saw again for an extended period of time, empty the oil tank and put in a small amount of regular engine oil (SAE 30), and then run the saw for a time. This is necessary to flush out all remaining bio-degradable oil from the oil tank, oil-feed system, chain and guide bar, as many such oils tend to leave sticky residues over time, which can cause damage to the oil pump or other parts.
Checking the chain lubrication Never work with the chain saw without sufficient chain lubrication. Otherwise the service life of the chain and guide bar will be reduced. Before starting work check the oil level in the tank and the oil feed. Check the oil feed rate as described below: Start the chain saw (see "Starting the engine”). Hold the running chain saw approx. 6" (15 cm) above a trunk or the ground (use an appropriate base).
Starting the engine Start the chain saw only after having assembled it completely and inspected! Move at least 10 feet (3 m) away from the place where you fuelled the saw. Make sure you have a good footing, and place the saw on the ground in such a way that the chain is not touching anything. Engage the chain brake (lock). Hold the tubular handle tightly with one hand and press the chain saw to the ground. Steady the rear handle by standing in the hand guard.
Checking the safety chain brake Do not work with the saw without first checking the chain brake! Start the engine as described (make sure you have a good footing, and place the saw on the ground in such a way that the blade is free of contact). Grasp the tubular handle firmly with one hand and hold the rear handle with the other. 7 With the engine running at moderate speed, press the hand guard (7) in the direction of the arrow with the back of your hand until the chain brake engages.
MAINTENANCE Sharpening the saw chain STOP CAUTION: Before doing any work on the guide bar or chain, always switch off the engine and pull the plug cap off the spark plug (see "Replacing the spark plug"). Always wear protective gloves! The chain needs sharpening when: The sawdust produced when sawing damp wood looks like wood flour. The chain penetrates the wood only under great pressure. The cutting edge is visibly damaged. The saw is pulled to the left or right when sawing.
Files and how to work with them Sharpen using a special file holder with a saw chain round file dia. 5/32" (4.0 mm). Normal round files are not appropriate for this work. See "Accessories" for the order number. The file should cut only when pushed forwards (arrow). Lift the file when leading it backwards. First sharpen the shortest cutter. The length of this cutter is then the standerd for all other cutters of the chain. Always guide the file horizontally (90o to the guide bar).
Cleaning the brake band and sprocket interior CAUTION: Before doing any work on the guide bar or chain, always switch off the engine and pull the plug cap off the spark plug (see "Replacing the spark plug"). Always wear protective gloves! STOP CAUTION: Start the chain saw only after having assembled it completely and inspected! Remove the sprocket guard (4) (See "PUTTING INTO OPERATION" figs. A and B) and clean the sprocket interior with a brush.
Replacing the saw chain 7 CAUTION: Use only chains and guide bars designed for this saw (see the Extract from the spare-parts list)! Check the sprocket (7) before mounting a new chain. Remove the sprocket guard (See "PUTTING INTO OPERATION" figs. A and H). CAUTION: Worn out sprockets (8) may damage the new chain and must therefore be replaced. 8 Do not attempt to replace the sprocket yourself. Sprocket replacement requires special training and tools and must be done at a MAKITA service center.
Replacing the spark plug 1 STOP CAUTION: Do not touch the spark plug or plug cap if the engine is running (high voltage). Switch off the engine before starting any maintenance work. A hot engine can cause burns. Wear protective gloves! .020 " The spark plug must be replaced in case of damage to the insulator, electrode erosion (burn) or if the electrodes are very dirty or oily. Remove the cover (see "Cleaning the air filter"). Pull the plug cap (1) off the spark plug.
Instructions for daily and periodic maintenance To ensure long life, prevent damage and ensure the full functioning of the safety features the following maintenance must be performed regularly. Guarantee claims can be recognized only if this work is performed regularly and properly. Failure to perform the prescribed maintenance work can lead to accidents! Perform the following servicing work daily after use. Make a habit of it, it does not require much time and your saw will always function properly.
Spare parts Reliable long-term operation, as well as the safety of your chain saw, depend among other things on the quality of the spare parts used. Use only original MAKITA parts, marked Only original spare parts and accessories guarantee the highest quality in material, dimensions, functioning and safety. Original spare parts and accessories can be obtained from your local dealer.
Extract from the spare parts list DCS 34 Use only original MAKITA parts. For repairs and replacement of other parts, see your MAKITA service center. Pos. MAKITA-No. 3 2 1 Qty. Denomination 1 442 035 661 1 Sprocket nose bar 14" (35 cm) 2 528 092 652 1 Saw chain 3/8" for 14" 1 442 040 661 1 Sprocket nose bar 16" (40 cm) 2 528 092 656 1 Saw chain 3/8" for 16" 3 952 100 633 1 Chain protection cover for 14"-16" 4 036 213 650 1 Sprocket guard, cpl.
ATTENTION! Une utilisation négligente ou incorrecte de ce produit peut entraîner des blessures graves ou mortelles! Avant d’utiliser une tronçonneuse ou d’autres produits MAKITA, il est important que vous ayez lu et entièrement compris et que vous suiviez avec soin les instructions fournies par le présent mode d’emploi. Le retour de chaîne peut entraîner des blessures graves ou mortelles et constitue l’un des nombreux dangers potentiels liés à l’utilisation d’une tronçonneuse.
Etendue de la fourniture 2 3 4 5 1. Tronçonneuse à essence 2. Guide 3. Chaîne 4. Housse de protection du guide 5. Outillage de montage 6.
Mesures de sécurité à respecter par les utilisateurs de tronçonneuses Lorsque vous utilisez la tronçonneuse, veuillez respecter les règles suivantes : a) Evitez tout contact entre la pointe du guide et tout objet. b) Le contact de la pointe peut entraîner un déplacement brutal du guide vers le haut et vers l’arrière et être à l’origine de blessures graves ou mortelles. c) Il faut toujours utiliser la tronçonneuse en la tenant des deux mains.
Mesures générales de sécurité max. CKA 21O L’utilisation de toute tronçonneuse peut être dangereuse. A plein régime, la chaîne peut atteindre une vitesse de 45 mph (20 m/s). Il est important que vous ayez lu et entièrement compris et que vous suiviez les mesures de sécurité et les mises en garde suivantes. Relisez de temps en temps le manuel d’emploi et les instructions de sécurité. ATTENTION! Les forces de réaction, y compris le choc de recul, peuvent être dangereuses.
Quels vêtements porter? La tronçonneuse L’utilisateur doit porter des vêtements robustes et ajustés mais qui lui laissent une complète liberté de mouvement. Evitez les vestes amples, les écharpes, les cravates, les bijoux, les pantalons à pattes d’éléphant ou à revers ou quoi que ce soit qui puisse se prendre dans la tronçonneuse ou les broussailles. Portez une combinaison ou des jeans munis de renforts de protection contre la coupe (fig. 3).
Instructions d’utilisation de la tronçonneuse Pour monter la tronçonneuse, suivez la procédure indiquée au chapitre „Montage du guide et de la chaîne“ de ce manuel d’emploi. La chaîne, le guide et le pignon MAKITA doivent être assortis (cf. chapitre correspondant de ce mode d’emploi). ATTENTION! Il est extrêmement important que la chaîne soit correctement tendue. Pour éviter un réglage incorrect, il faut tendre la chaîne en suivant la procédure indiquée dans ce manuel d’emploi.
Réglages importants ATTENTION! Lorsque le ralenti est correctement réglé, la chaîne ne doit pas tourner. Pour le réglage du ralenti, reportez-vous au chapitre correspondant de ce manuel d’emploi. N’utilisez pas de tronçonneuse dont le ralenti n’est pas correctement réglé. Réglez le ralenti vous-même de la façon indiquée dans le chapitre correspondant de ce manuel d’emploi. Demandez à votre revendeur MAKITA d’examiner votre tronçonneuse et de procéder aux réglages corrects ou aux réparations.
9 Pour garder la maîtrise de votre tronçonneuse, ayez toujours une position stable au sol. Ne travaillez jamais sur une échelle, dans un arbre ou sur tout autre support instable. N’utilisez jamais la tronçonneuse plus haut qu’à hauteur d’épaules (fig. 9). 10 11 Positionnez la chaîne de sorte que votre corps soit éloigné du dispositif de coupe lorsque le moteur tourne (fig. 10). N’appuyez pas sur la tronçonneuse lorsque vous arrivez à la fin d’une coupe.
De nombreux facteurs déterminent l’apparition et la force de la réaction de choc de recul. Le type du guide et de la chaîne utilisés jouent également un rôle dans la force de la réaction de choc de recul. La vitesse à laquelle la chaîne entre en contact avec l’objet. La force de choc de recul est proportionnelle à l’impact. L’angle de contact entre la pointe du guide et le corps étranger (fig. 11). Le choc de recul est plus marqué dans le quadrant supérieur de la pointe du guide.
Le recul: Pour éviter la traction Le recul se produit lorsque la chaîne se trouvant sur la partie supérieure du guide est arrêtée subitement lorsqu’elle est coincée, prise ou rencontre un corps étranger dans le bois. La réaction de la chaîne pousse la tronçonneuse directement vers l’utilisateur, lui faisant perdre le contrôle de la tronçonneuse. Le recul se produit souvent lorsque l’on coupe avec la partie supérieure du guide (fig. 14). 1.
45° 2 12 première coupe 45° seconde coupe = zone d’abattage 20 17 Lors de l’abattage, respectez une distance d’au moins 2 fois et demi la hauteur de l’arbre entre l’arbre et la personne la plus proche (cf. fig. 17). Remarque: Tout avertissement peut être couvert par le bruit de votre moteur. Si l’arbre a de grosses racines latérales, coupez dans les plus grandes racines, d’abord verticalement puis horizontalement et enlevez le morceau ainsi découpé (fig. 20).
Amorcez la coupe d’abattage légèrement plus haut que l’encoche d’abattage sur le côté opposé de l’arbre (fig. 22). Coupez ensuite horizontalement dans la direction de l’encoche d’abattage. Appliquez la tronçonneuse avec ses griffes directement derrière la partie de bois non coupée et coupez en direction de l’encoche d’abattage (fig. 23). Laissez une portion non coupée égale à environ 1/10 du diamètre de l’arbre. Cette portion constitue le tenant (fig. 23).
Débitage 3 Le débitage consiste à découper un rondin en plusieurs morceaux. 2 1 29 ATTENTION! A ce point, il y a un très grand danger de choc de recul. Il faut être extrêmement prudent pour garder le contrôle de la tronçonneuse. Pour faire la coupe d’abattage, suivez la méthode de sectionnement décrite précédemment (fig. 29). Si vous n’avez pas l’expérience du travail avec une tronçonneuse, n’essayez pas de faire de coupe en plongée. Demandez l’assistance d’un professionnel.
Entretien et réparation N’utilisez jamais une tronçonneuse endommagée, incorrectement réglée ou incomplètement ou incorrectement assemblée. Respectez les instructions d’entretien et de réparation du chapitre correspondant du présent manuel d’emploi. 1. coupe de décharge côté pression côté tension 2. coupe transversale ATTENTION! 33 2.
Désignation des pièces 1 2 3 4 5 9 7 6 8 24 25 10 11 12 13 14 15 23 22 21 Plaque signatique 20 DCS 34 9905 123456 528.092.656 442.040.661 16" inch (40 cm) 22045 Hamburg, Germany 19 18 17 16 Année de construction Numéro de série à indiquer lors de commande de pièces de rechange! 036.100.
Caractéristiques techniques Monocylindre à deux temps Cylindrée Alésage Course Puissance maxi/régime Couple maxi/régime Ralenti Niveau sonore à pleine charge mesuré aux oreilles de l'opérateur selon ANSI B 175.1 Niveau sonore pour une personne voisine (à une distance de 50ft/15 m) selon ANSI B 175.
MISE EN ROUTE ATTENTION: Pour tous travaux effectués sur le guide de la chaîne de sciage, le moteur doit être impérativement arrêté et la fiche de bougie doit être enlevée (voir paragraphe pour le remplacement de la bougie) et le port de gants de protection est obligatoire! STOP ATTENTION: La tronçonneuse ne peut être démarrée qu’après le montage complet et le contrôle effectué! A Montage du guide et de la chaîne de sciage Utiliser la clé combinée livrée avec la machine pour les travaux suivants.
11 Poser la chaîne de sciage (8) sur le plateau (9). Introduire avec la main droite la chaîne de sciage dans la rainure de guidage supérieure du guide de la chaîne (10). Les arêtes coupantes de la chaîne de sciage doivent être dirigées dans le sens de la flèche sur la partie supérieure du guide (11)! 8 9 10 8 E 12 Guider la chaîne de sciage (8) autour de l’étoile de renvoi (12) du guide de la chaîne, en tirant légèrement la chaîne de sciage dans le sens de la flèche.
Contrôle de la tension de la chaîne STOP Une tension correcte de la chaîne est réalisée lorsque la chaîne s’applique sur le guide inférieur et qu’elle peut encore être légèrement écartée du guide à la main. Ce faisant, le frein de la chaîne doit être libéré. Contrôler fréquemment la tension de la chaîne, les chaînes neuves ayant tendance à s’allonger ! Par conséquent, vérifier souvent la tension de la chaîne le moteur étant arrêté.
Carburants ATTENTION: L’appareil est utilisé avec des produits d’huiles minérales (essence et huile)! Votre attention est requise lorsque vous manipulez l’essence. II est interdit de fumer et tout feu immédiat n’est pas autorisé (risque d’explosion). Carburant Mélange carburant Le moteur de la tronçonneuse est un moteur thermique à deux temps de haute performance. Ce moteur est alimenté par un mélange de carburant et d’huile moteur deux temps.
Remarque importante pour les huiles de chaîne de sciage bio Avant une longue mise hors service, le réservoir à huile doit être vidé et rempli ensuite d’un peu d’huile moteur (SAE 30). Ensuite, faire marcher la tronçonneuse pendant quelques temps de manière à rincer les restes d’huile bio du réservoir, du systéme de conduite d’huile et du dispositif de sciage.
Vérifier le graissage de la chaîne Ne jamais scier sans graissage suffisant. Vous risquez sinon de réduire la durée de vie du dispositif de sciage! Vérifier avant de démarrer le travail la quantité d’huile dans le réservoir, ainsi que le débit d’huile. Le débit d’huile peut être vérifié de la manière suivante: Démarrer la tronçonneuse. Maintenir la chaîne de sciage en marche env. 6" (15 cm) par dessus une souche d’arbre ou le sol (choisir une base adéquate).
Démarrer le moteur La tronçonneuse ne peut être démarrée qu’après le montage complet et le contrôle effectué! Démarrer le moteur au moins 10 pieds (3 m) de l’endroit du réservoir. Prendre une position stable et sure, puis placer la tronçonneuse sur le sol pour que le dispositif de sciage soit dégagé. Libérer le frein de chaîne (bloquer). Saisir fermement la poignée-étrier avec une main et plaquer la tronçonneuse sur le sol. Placer la pointe du pied droit dans le protège-main arrière.
Vérifier le frein de chaîne Le frein de chaîne doit être vérifié avant de commencer tous travaux. Démarrer le moteur comme décrit (prendre une position stable et poser la tronçonneuse sur le sol de façon à ce que le dispositif de sciage soit libre). Bien tanier la poignée-étrier d’une main, l’autre main étant sur la manette. 7 Laisser tourner le moteur à mi-vitesse et appuyer sur le protège-mains (7) avec le dos de la main dans la sens de la flèche jusqu’à ce que le frein de chaîne se bloque.
TRAVAUX DE MAINTENANCE Affûtage de la chaîne de sciage STOP ATTENTION: Pour tous travaux effectués sur le guide de la chaîne de sciage, le moteur doit être impérativement arrêté et la fiche de bougie doit être enlevée (voir pragraphe pour le remplacement de la bougie) et le port de gants de protection est obligatoire! La chaîne de sciage doit être affûtée lorsque : les copeaux deviennent farineux en sciant du bois humide.
Lime et guidage de la lime Pour affûter la lime, il faut utiliser un porte-lime spécial avec une lime ronde de chaîne de sciage ø 5/32" (4,0 mm). Les limes rondes normales ne sont pas appropriées. Numéro de commande, voir accessoires. La lime ne doit attaquer que lors de la passe en avant (flèche). Lors du retour, relever la lime du matériel. La dent de rabotage la plus courte est affûtée la première.
Nettoyer l’intérieur de la bande de frein de chaîne et de la roue à chaîne ATTENTION: Pour tous travaux effectués sur le guide de la chaîne de sciage, le moteur doit être impérativement arrêté et la fiche de bougie doit être enlevée (voir pragraphe pour le remplacement de la bougie) et le port de gants de protection est obligatoire! STOP ATTENTION: La tronçonneuse ne peut être démarrée qu’après le montage complet et le contrôle effectué! Enlever la protection de roue à chaîne (4) (voir chapitre «MISE EN R
Nouvelle chaîne de sciage 7 ATTENTION: N’utiliser que des chaînes et guide permises pour cette tronçonneuse (voir extrait de la liste de pièces de rechange)! Avant de monter une nouvelle chaîne de sciage, il faut vérifier l’état de la roue à chaîne (7). Enlever la protection de roue à chaîne (voir chapitre „MISE EN ROUTE“ A-H) ATTENTION : Des roues à chaîne usées (8) provoquent des détériorations sur une nouvelle chaîne de sciage et doivent impérativement être remplacées.
Remplacement de bougie 1 STOP ATTENTION: Les bougies d’allumage ou la fiche de la bougie ne doivent pas être touchés le moteur en marche (haute tension). N’effectuer des travaux de maintenance que si le moteur est arrêté. Risque de brûlure lorsque le moteur est chaud: porter absolument vos gants de protection! 0,5 mm En cas de détérioration du corps isolant, d’usure importante des électrodes resp. d’électrodes très encrassées ou pleines d’huile, il faut procéder à un remplacement de la bougie.
Indications de maintenance et d’entretien périodiques De manière à garantir une longue durée de vie et le plein fonctionnement des dispositifs de sécurité et à éviter des détériorations, il faut effectuer régulièrement les travaux de maintenance décrits ci-dessous. Les réclamations ne pourront être reconnues comme telles si ces travaux ont été effectuées régulièrement et correctement. Des accidents risquent de se produire en cas de nonobservation.
Pièces de rechange Le fonctionnement permanent fiable et la sécurité de votre appareil dépend aussi de la qualité des pièces de rechange utilisées. N’utilisez que des pièces de rechange d’origine MAKITA, signalées par Seules les pièces d’origine proviennent de la chaîne de production de l’appareil et vous assurent donc la qualité optimale du matériau, du respect des dimensions et du fonctionnement et une sécurité irréprochables.
Extrait de la liste des pièces de rechange DCS 34 N’utilisez que des pièces de rechange d’origine MAKITA. Pour les réparations et la rechange pour d’autres pièces, votre atelier spécialisé MAKITA est compétent. 3 2 Pos. N°MAKITA pcs.
Changements sans préavis DOLMAR Division 1950 Forbes Street Whitby, Ontario Canada, L1N 7B7 Form: 995 707 681 (9.99 GB, F) Makita Canada Inc. 14930 Northam Street La Mirada CA 90638-5753 USA Specifications subject to change without notice Makita U.S.A., Inc.