ENGLISH: Original instructions INSTRUCTION MANUAL Cordless Angle Drill DA332D DA333D Read before use.
SPECIFICATIONS Model: DA332D Drilling capacities DA333D Steel 10 mm Wood 12 mm 0 - 1,100 min-1 No load speed Overall length 313 mm - 332 mm Rated voltage D.C. 10.8 V - 12 V max Battery cartridge BL1015 / BL1016 / BL1020B / BL1021B / BL1040B / BL1041B Net weight • • • 1.2 - 1.3 kg 1.2 - 1.4 kg Due to our continuing program of research and development, the specifications herein are subject to change without notice. Specifications and battery cartridge may differ from country to country.
2. SAFETY WARNINGS General power tool safety warnings 3. WARNING: Read all safety warnings, instruc- tions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. 4. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. 5. Work area safety 1.
3. 4. 5. 6. 7. 8. 9. Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
3. 4. 5. 6. 7. 8. 9. 10. 11. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material.
Low battery voltage: The remaining battery capacity is too low and the tool will not operate. If you turn the tool on, the motor does not run or the motor runs again but stops soon. In this situation, remove and recharge the battery. Indicating the remaining battery capacity Only for battery cartridges with the indicator Switch action CAUTION: Before installing the battery cartridge into the tool, always check to see that the switch lever actuates properly and returns to the "OFF" position when released.
For model DA333D ASSEMBLY 1 CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. Installing or removing drill bit Optional accessory For model DA332D ► 1. Lamp Pull the switch lever to light up the lamp. The lamp keeps on lighting while the switch lever is being pulled. The light automatically goes out approximately 10 seconds after the switch lever is released.
Installing hook OPERATION CAUTION: Always insert the battery cartridge all the way until it locks in place. If you can see the red indicator on the upper side of the button, it is not locked completely. Insert it fully until the red indicator cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. 1 2 CAUTION: When the speed comes down extremely, reduce the load or stop the tool to avoid the tool damage.
Drilling operation OPTIONAL ACCESSORIES Drilling in wood When drilling in wood, the best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the drill bit into the workpiece. CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan www.makita.