ENGLISH Cordless 4 Mode Impact Driver MODEL BTP130 MODEL BTP140 007155 I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
SPECIFICATIONS Model Max.
EC-DECLARATION OF CONFORMITY We declare under our sole responsibility that this product is in compliance with the following standards of standardized documents; EN60745, EN55014 in accordance with Council Directives, 89/336/EEC, 98/37/EC. Yasuhiko Kanzaki CE2005 MAKITA INTERNATIONAL EUROPE LTD. Michigan Drive, Tongwell, Milton Keynes, Bucks MK15 8JD, ENGLAND Responsible manufacturer: Makita Corporation Anjo Aichi Japan Director GENERAL SAFETY RULES GEA002-3 WARNING: Read all instructions.
12. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. 24. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. 13. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. 25.
8. Wear ear protectors with impact drills. Exposure to noise can cause hearing loss. SAVE THESE INSTRUCTIONS. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. 2. 3. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life. Charge the battery cartridge with room temperature at 10°C - 40°C (50°F - 104°F). Let a hot battery cartridge cool down before charging it.
FUNCTIONAL DESCRIPTION • 006667 Installing or removing battery cartridge • 1 2 • • 3 1. Red part 2. Button 3. Battery cartridge • 007165 CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. Always switch off the tool before insertion or removal of the battery cartridge. To remove the battery cartridge, withdraw it from the tool while sliding the button on the front of the cartridge.
• • • CAUTION: Always check the direction of rotation before operation. Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. When not operating the tool, always set the reversing switch lever to the neutral position. Selecting the action mode This tool employs an action mode changing lever. Select one of the four modes suitable for your work needs by using this lever.
007162 Sliding to the mark is high rotation and the mark is low rotation. Before operation, always make sure that the lever is correctly set to your desired mode mark and use the tool at an appropriate speed for your work. • 1 • 1. Action mode changing lever 007163 CAUTION: When using the action mode change lever, use only when the tool stops. But when the lever does not easily move, pull the switch trigger slightly to rotate the spindle and then move the lever.
For other countries 006349 A=17mm To install these types of bits, follow the procedure (1). B=14mm (Note) Makita bits are these types. A=12mm B=9mm 1 001267 1. 004347 2. To install these types of bits, follow the procedure (2). (Note) Bit-piece is necessary for installing the bit. To install the bit, pull the sleeve in the direction of the arrow and insert the bit into the sleeve as far as it will go. Then release the sleeve to secure the bit. 2 1. Bit 2.
OPERATION • CAUTION: Always insert the battery cartridge all the way until it locks in place. If you can see the red part on the upper side of the button, it is not locked completely. Insert it fully until the red part cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. Impact driver operation When driving wood screws or bolts. set the action mode changing lever to the mark. The adjusting ring can be placed at any position.
Tightening bolts 007318 Standard bolt Nm (kgf cm) 120 (1224) M14 100 (1020) NOTE: M12 (M14) Fastening torque 60 (612) (M12) M10 (M10) 20 (204) M8 (M8) Proper fastening torque • • 80 (816) 40 (408) 0 3.0 1.0 2.0 0 Fastening time ( S) 007320 M12 Fastening torque 60 (612) M10 (M10) M8 40 (408) 20 (204) 0 0 (M8) 1.0 2.0 3.0 Fastening time ( S) Proper fastening torque (M12) 80 (816) • • Use the proper bit for the head of the screw/bolt that you wish to use.
• CAUTION: If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. Screwdriving operation CAUTION: • Adjust the adjusting ring to the proper torque level for your work. When driving small wood screws or machine screws. set the action mode changing lever to the mark. Adjust the adjusting ring to the proper torque level for your work.
Drilling in metal To prevent the bit from slipping when starting a hole, make an indentation with a center-punch and hammer at the point to be drilled. Place the point of the bit in the indentation and start drilling. Use a cutting lubricant when drilling metals. The exceptions are iron and brass which should be drilled dry. • • • • • MAINTENANCE • 006258 CAUTION: Pressing excessively on the tool will not speed up the drilling.
006260 Raise the arm part of the spring and then place it in the recessed part of the housing with a slotted bit screwdriver of slender shaft or the like. 1 2 3 1. Spring 2. Arm 3. Recessed part 006261 Use pliers to remove the carbon brush cap of the carbon brushes. Take out the worn carbon brushes, insert the new ones and replace the carbon brush cap in reverse. 006304 Make sure that the carbon brush cap have fit into the holes in brush holders securely.
Memo 15
Makita Corporation Anjo, Aichi, Japan 884655-223