DC18RD Two Port Multi Fast Charger Chargeur Rapide 2 Batteries Multi-Cargador Rápido de Dos Puertos IMPORTANT: Read Before Using. IMPORTANT : Lire ce qui suit avant d’utiliser cet outil. IMPORTANTE: Leer antes de usar. Symbols The followings show the symbols used for the charger and battery. Be sure that you understand their meaning before use. Symboles Nous donnons ci-dessous les symboles utilisés pour le chargeur et la batterie.
• Cooling abnormality • Problème de refroidissement • Anormalidad en la carga • Do not short batteries. • Ne jamais court-circuiter les bornes d’une batterie. • No provoque un cortocircuito en las baterías.
ENGLISH SPECIFICATIONS Model DC18RD Input A.C. 120 V 50 – 60 Hz / 50/60 Hz Output Weight For MAKITA Battery D.C. 7.2 V / 7.2 V – 18 V For USB Device D.C. 5 V / D.C. 1.5 A 1.9 kg (4.127 lbs) • Manufacturer reserves the right to change specifications without notice. • Note: Specifications may differ from country to country. • Weight according to EPTA-Procedure 01/2003. IMPORTANT SAFETY INSTRUCTIONS CAUTION: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18.
Changing melody sound of completed charging 1. 2. 3. 4. 5. 6. Insert the battery cartridge into the charging port that you want to change the melody sound of completed charging. It brings out the last preset brief melody sound of completed charging. Removing and re-inserting it within five seconds after this action makes the melody sound change. Every time removing and re-inserting it within another five seconds after this, the melody sound changes in order.
Using with USB device This charger works as an external power supply for USB device. 1. Open the cover of the USB power supply port. Connect the USB cable to the USB power supply port and USB device. 2. Plug the charger into a power source. 3. After charging, unplug the charger. Note: • The charger may not supply power to some USB devices. • Before connecting USB device to the charger, always backup your data of USB device. Otherwise your data may lose by any possibility.
FRANÇAIS SPÉCIFICATIONS Modèle DC18RD Entrée C.A. 120 V 50 – 60 Hz / 50/60 Hz Sortie Poids Pour les batteries MAKITA C.C. 7,2 V / 7,2 V – 18 V Pour le dispositif USB C.C. 5 V / C.C. 1,5 A 1,9 kg (4,127 lbs) • Le fabricant se réserve le droit de modifier sans avertissement les spécifications. • Remarque : Les spécifications peuvent varier selon les pays. • Poids selon la procédure EPTA 01/2003. LES CONSIGNES DE SECURITE IMPORTANTES ATTENTION : 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15.
Chargement des batteries MAKITA Ce chargeur permet de charger deux batteries simultanément. 1. Branchez le chargeur sur une source de courant alternatif dont la tension est adaptée. Le témoin de charge clignote en vert de manière répétée. 2. Insérer la batterie dans le chargeur jusqu’à ce qu’elle s’arrête, ajustée sur le guide du chargeur. Le couvre-bornes du chargeur peut être ouvert en insérant la batterie, et fermé en la retirant. 3.
Charge de remise en condition La charge de remise en condition peut faire augmenter la durée de vie de la batterie en effectuant automatiquement une recherche du niveau de charge optimale des batteries dans toute situation. Une batterie utilisée à plusieurs reprises dans les conditions suivantes nécessitera une “charge de remise en condition” pour éviter qu’elle ne s’use rapidement. Dans ce cas, le témoin jaune s’allume. 1. Recharge de la batterie alors qu’elle est très chaude. 2.
ESPAÑOL ESPECIFICACIONES Modelo Entrada Salida Peso DC18RD 120 V 50 – 60 Hz / 50/60 Hz Para batería MAKITA 7,2 V cc / 7,2 V cc – 18 V cc Para dispositivo USB 5 V cc / 1,5 A cc 1,9 kg (4,127 lbs) • El fabricante se reserva el derecho a cambiar las especificaciones sin aviso. • Nota: Las especificaciones podrán cambiar de un país a otro. • Peso de acuerdo con el procedimiento EPTA 01/2003. INSTRUCCIONES DE SEGURIDAD IMPORTANTES PRECAUCION: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.
Carga de baterías MAKITA Este cargador puede cargar dos baterías al mismo tiempo. 1. Enchufe el cargador en una toma de corriente de la tensión de CA apropiada. La luz de carga parpadeará en color verde repetidamente. 2. Inserte el cartucho de batería en el cargador hasta que haga tope ajustándose a la guía del cargador. La tapa del terminal del cargador se abre al insertar el cartucho de batería y se cierra al sacarlo. 3.
Carga de acondicionamiento La carga de acondicionamiento puede alargar la vida útil de la batería buscando automáticamente la condición óptima para la carga de la batería en cualquier situación. La batería empleada en las siguientes condiciones repetidamente requerirá una “carga de acondicionamiento” para evitar que su vida de servicio no se acorte rápidamente. En ese caso, se encenderá la luz amarilla. 1. Si la carga estando caliente. 2. Si la carga estando fría. 3.
Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885372-949 IDE www.makita.
INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES Cordless Circular Saw Scie Circulaire sans Fil Sierra Circular Inalámbrica XSS01 XSS02 006699 IMPORTANT: Read Before Using. IMPORTANT: Lire avant usage. IMPORTANTE: Leer antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model XSS01 Blade diameter Max. Cutting depth XSS02 165 mm (6-1/2") at 90° 57 mm (2-1/4") at 45° 40 mm (1-9/16") at 50° 36 mm (1-7/16") No load speed (RPM) 3,700 /min Overall length 347 mm (13-5/8") Net weight 3.2 kg (7.1 lbs) Rated voltage 3.5 kg (7.6 lbs) 3.1 kg (6.8 lbs) 3.3 kg (7.3 lbs) D.C.
26. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. 27. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.
12. 5. Hold the power tool by insulated gripping surfaces only, when performing an operation where the cutting tool may contact hidden wiring. Contact with a "live" wire will also make exposed metal parts of the power tool "live" and could give the operator an electric shock. 6. When ripping, always use a rip fence or straight edge guide. This improves the accuracy of cut and reduces the chance of blade binding. 7. Always use blades with correct size and shape (diamond versus round) of arbour holes.
Additional safety warnings 23. Intended use This tool is intended to cut wood products only. Accumulated sawdust on the lower guard and hub from other materials may effect the proper closure of the lower guard which could lead to serious personal injury. 24. Use extra caution when cutting damp wood, pressure treated lumber, or wood containing knots. Maintain smooth advancement of tool without decrease in blade speed to avoid overheating the blade tips. 25.
ENC007-8 IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CARTRIDGE 1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 2. Do not disassemble battery cartridge. 3. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. 4.
Battery protection system (Lithium-ion battery with star marking) FUNCTIONAL DESCRIPTION • CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. 1. Star marking 1 Installing or removing battery cartridge 1 2 1. Red indicator 2. Button 3. Battery cartridge 012128 Lithium-ion batteries with a star marking are equipped with a protection system.
Bevel cutting Switch action 1. Lever 1 2 1. Switch trigger 2. Lock-off lever 1 006702 006705 For Model XSS01 CAUTION: Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. • Do not pull the switch trigger hard without pressing the lock-off lever. This can cause switch breakage. To prevent the switch trigger from being accidentally pulled, a lock-off lever is provided.
NOTE: • Use a dry cloth to wipe the dirt off the lens of lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination. • Do not use gasoline, thinner or the like to clean the lens of lamp. Using such substances will damage the lens. Hex wrench storage 1. Hex wrench 1 ASSEMBLY • CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool.
• If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. 1 2 MAINTENANCE 1. Rear handle 2. Front grip 3. Base • • 3 006709 Hold the tool firmly. The tool is provided with both a front grip and rear handle. Use both to best grasp the tool. If both hands are holding saw, they cannot be cut by the blade. Set the base on the workpiece to be cut without the blade making any contact.
Replacing carbon brushes Combination 1. Limit mark General purpose blade for fast and smooth rip, crosscuts and miters. 006540 • • • • Rip fence (Guide rule) Hex wrench 5 Dust nozzle Makita genuine battery and charger 1 NOTE: • Some items in the list may be included in the tool package as standard accessories. They may differ from country to country. 001145 Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark.
FRANÇAIS (Mode d’emploi original) SPÉCIFICATIONS Modèle XSS01 Diamètre de la lame Profondeur de coupe max. XSS02 165 mm (6-1/2") à 90° 57 mm (2-1/4") à 45° 40 mm (1-9/16") à 50° 36 mm (1-7/16") Vitesse à vide (T/MIN) 3 700 /min Longueur totale 347 mm (13-5/8") Poids net 3,2 kg (7,1 lbs) Tension nominale 3,5 kg (7,6 lbs) 3,1 kg (6,8 lbs) 3,3 kg (7,3 lbs) C.C.
Sécurité personnelle 10. Restez alerte, attentif à vos mouvements et faites preuve de bon sens lorsque vous utilisez un outil électrique. Évitez d'utiliser un outil électrique si vous êtes fatigué ou si vous avez pris une drogue, de l'alcool ou un médicament. Un moment d'inattention pendant l'utilisation d'un outil électrique peut entraîner une grave blessure. 11. Portez des dispositifs de protection personnelle. Portez toujours un protecteur pour la vue.
contact avec un conducteur sous tension, les pièces métalliques à découvert de l'outil deviendraient également sous tension et risqueraient de transmettre une décharge à l'utilisateur. 6. Lors du sciage en long, utilisez toujours un garde parallèle ou un guide de coupe rectiligne. Cela améliore la précision de la coupe et réduit le risque de coincement de la lame. 7. Employez toujours une lame de diamètre approprié et dont le trou central est de forme correcte (angulaire ou ronde).
15. la cause du coincement de la lame et prenez les mesures correctives pour éliminer le problème. 11. Avant de faire redémarrer la scie dans la pièce, centrez la lame dans le trait de scie et assurez-vous que les dents de la lame ne mordent pas déjà dans le matériau. Si la lame est coincée, elle risque de remonter dans le trait de scie ou de causer un recul au moment du redémarrage de la scie. 12.
rappel et libérez le protecteur inférieur dès que la lame pénètre dans le matériau. Pour toute autre opération de sciage, le protecteur inférieur devrait fonctionner automatiquement. 21. Assurez-vous toujours que le protecteur inférieur couvre bien la lame avant de déposer l'outil sur l'établi ou sur le sol. Si la lame n'est pas protégée et n'a pas fini de tourner, elle entraînera la scie vers l'arrière en coupant tout sur son passage.
31. 32. 33. 34. 35. N'appliquez jamais une pression latérale sur la lame pour l'arrêter. N'utilisez aucune meule abrasive. N'utilisez que la lame dont le diamètre correspond aux indications données sur l’outil ou dans le manuel. L’utilisation d’une lame d’une taille incorrecte peut affecter la protection de la lame ou le fonctionnement du protecteur et cela pourrait causer de graves blessures. Maintenez la lame affûtée et propre.
Système de protection de la batterie (batterie lithium-ion marquée d’une étoile) DESCRIPTION DU FONCTIONNEMENT 1. Étoile 1 • ATTENTION: Assurez-vous toujours que l'outil est hors tension et que sa batterie est retirée avant de l'ajuster ou de vérifier son fonctionnement. Installation ou retrait de la batterie 1 2 1. Indicateur rouge 2. Bouton 3. Batterie 012128 Les batteries lithium-ion marquées d’une étoile sont équipées d’un système de protection.
d'une dent de lame ne dépasse sous la pièce. L'utilisation d'une profondeur de coupe adéquate aide à réduire les risques de chocs en retour dangereux qui peuvent causer des blessures. Interrupteur 1 Coupe en biseau 2 1. Gâchette 2. Levier de sécurité 1. Levier 006705 ATTENTION: Avant d'insérer la batterie dans l'outil, vérifiez toujours que la gâchette fonctionne bien et revient en position d'arrêt lorsque relâchée.
Pour allumer la lumière sans faire démarrer l'outil, appuyez sur la gâchette sans appuyer sur le levier de déverrouillage. Pour allumer la lumière et faire démarrer l'outil, appuyez sur le levier de déverrouillage et appuyez sur la gâchette alors que le levier de verrouillage est enfoncé. 2 3 NOTE: • Utilisez un chiffon sec pour essuyer la saleté qui recouvre la lentille de la lampe. Prenez garde de rayer la lentille de la lampe, pour éviter une diminution de l'éclairage.
Garde parallèle (règle de guidage) UTILISATION • • • 1. Vis de serrage 2. Garde parallèle (règle de guidage) ATTENTION: Insérez toujours la batterie jusqu'au fond, jusqu'à ce qu'elle verrouille en place. Si vous pouvez voir la partie rouge de la face supérieure du bouton, la batterie n'est pas parfaitement verrouillée. Insérez-la à fond, jusqu'à ce que la partie rouge ne soit plus visible.
demande de réparation auprès du centre de service après-vente Makita le plus près. Réglage de précision pour la coupe à 90° (coupe verticale) Pour le modèle XSS02 Ce réglage est réalisé en usine. S'il se défait, ajustez la vis de réglage au moyen d'une clé hexagonale tout en mesurant l'angle de 90° de la lame par rapport à la base à l'aide d'une règle triangulaire, d'une équerre, etc. 2 1 1 2 1. Réglage de la vis à 45 ゚ (XSS01 seulement) 2.
GARANTIE LIMITÉE D’UN AN MAKITA Politique de garantie Chaque outil Makita est inspecté rigoureusement et testé avant sa sortie d’usine. Nous garantissons qu’il sera exempt de défaut de fabrication et de vice de matériau pour une période d’UN AN à partir de la date de son achat initial. Si un problème quelconque devait survenir au cours de cette période d’un an, veuillez retourner l’outil COMPLET, port payé, à une usine ou à un centre de service après-vente Makita.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo XSS01 Diámetro del disco Profundidad de corte máxima XSS02 165 mm (6-1/2") a 90° 57 mm (2-1/4") a 45° 40 mm (1-9/16") a 50° 36 mm (1-7/16") Velocidad sin carga (r.p.m.) 3 700 r/min Longitud total 347 mm (13-5/8") Peso neto 3,2 kg (7,1 lbs) 3,5 kg (7,6 lbs) Tensión nominal 3,1 kg (6,8 lbs) 3,3 kg (7,3 lbs) 18 V c.c.
19. Desconecte la clavija de la fuente de energía y/o la batería de la herramienta eléctrica antes de realizar ajustes, cambiar accesorios o guardar las herramientas eléctricas. Dichas medidas de seguridad preventivas reducen el riesgo de que la herramienta se inicie accidentalmente. 20. Guarde la herramienta eléctrica que no use fuera del alcance de los niños y no permita que las personas que no están familiarizadas con ella o con las instrucciones la operen.
27. En condiciones abusivas, podrá escapar líquido de la batería; evite tocarlo. Si lo toca accidentalmente, enjuague con agua. Si hay contacto del líquido con los ojos, acuda por ayuda médica. Puede que el líquido expulsado de la batería cause irritación o quemaduras. Servicio de mantenimiento 28. Haga que una persona calificada repare la herramienta utilizando sólo piezas de repuesto idénticas. Esto asegura que se mantenga la seguridad de la herramienta eléctrica. 29.
11. 12. inmóvil en el material hasta que el disco se pare completamente. No intente nunca extraer el disco de la pieza de trabajo ni tirar de la sierra hacia atrás mientras el disco esté moviéndose porque podrá ocasionar un retroceso brusco. Investigue y tome medidas correctivas para eliminar la causa del atoramiento del disco. Cuando vuelva a poner en marcha la sierra sobre la pieza de trabajo, centre la sierra en la entalladura y compruebe que sus dientes no estén en contacto con el material.
especiales como “cortes de cavidad” y “cortes compuestos.” Levante el protector inferior mediante el mango retráctil y cuando el disco entre en el material, debe soltar el protector inferior. Para todos los otros cortes con sierra, el protector inferior debe funcionar automáticamente. 21. Antes de dejar la sierra en el banco o en el suelo, observe siempre que el protector inferior esté cubriendo el disco.
31. 32. 33. 34. 35. No detenga el disco de la sierra mediante presión lateral sobre el mismo. No use ningún disco abrasivo. Use solamente un disco de sierra cuyo diámetro esté marcado en la herramienta o especificado en el manual. El uso de un disco de sierra de tamaño inadecuado puede que afecte la protección del disco o del protector en sí, lo cual podría resultar en graves lesiones al operador. Mantenga el disco afilado y limpio.
Sistema de protección de batería (batería de ión de litio con marca de estrella) DESCRIPCIÓN DEL FUNCIONAMIENTO 1. Marca de estrella 1 • PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería extraído antes de realizar cualquier ajuste o comprobación en la herramienta. Instalación o desmontaje del cartucho de batería 1 2 012128 Las baterías de ión de litio con una marca de estrella están equipadas con un sistema de protección.
Afloje la palanca del lateral del mango posterior y mueva la base hacia arriba o hacia abajo. Cuando haya alcanzado la profundidad de corte deseada, fije la base apretando la palanca. Para obtener cortes más limpios y seguros, ajuste la profundidad de corte de forma que no sobresalga más de un diente del disco de sierra por debajo de la pieza de trabajo.
Utilice solamente la llave Makita para instalar o desmontar el disco. Para quitar el disco, presione el bloqueo del eje de forma que el disco no pueda girar y afloje el perno hexagonal girándolo en sentido de las agujas del reloj con la llave. Después quite el perno hexagonal, la brida exterior y el disco. Para instalar el disco, siga el procedimiento de desmontaje a la inversa. ASEGÚRESE DE APRETAR EL PERNO HEXAGONAL EN SENTIDO CONTRARIO A LAS AGUJAS DEL RELOJ FIRMEMENTE.
velocidad. Ahora simplemente mueva la herramienta hacia delante sobre la superficie de la pieza de trabajo, manteniéndola plana y avanzando suavemente hasta completar el corte. Para obtener cortes limpios, mantenga la línea de corte recta y la velocidad de avance uniforme. Si se desvía de la línea de corte prevista, no intente girar ni forzar la herramienta para hacerla volver a la línea de corte. Esta acción podría inmovilizar el disco y ocasionar un peligroso retroceso brusco y posibles heridas graves.
Utilice un destornillador para quitar las tapas de los portaescobillas. Extraiga las escobillas gastadas, inserte las nuevas y vuelva a colocar las tapas. Para modelo XSS01 Después de reemplazar las escobillas, inserte el cartucho de batería en la herramienta y hágale el rodaje a las escobillas haciendo funcionar la herramienta sin carga durante 1 minuto aproximadamente. Después compruebe la herramienta mientras está en marcha y la operación del freno eléctrico cuando suelte el gatillo interruptor.
GARANTÍA LIMITADA MAKITA DE UN AÑO Ésta Garantía no aplica para México Política de garantía Cada herramienta Makita es inspeccionada y probada exhaustivamente antes de salir de fábrica. Se garantiza que va a estar libre de defectos de mano de obra y materiales por el periodo de UN AÑO a partir de la fecha de adquisición original.
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES Cordless Hammer Driver Drill Rotomartillo Atornillador Inalámbrico XPH12 IMPORTANT: Read Before Using. IMPORTANTE: Lea antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model: Drilling capacities Fastening capacities XPH12 Masonry 13 mm (1/2") Steel 13 mm (1/2") Wood 38 mm (1/1/2") Wood screw 10 mm x 90 mm (3/8" x 3-1/2") Machine screw No load speed (RPM) Blows per minute M6 (1/4") High (2) 0 - 2,000 /min Low (1) 0 - 500 /min High (2) 0 - 30,000 /min Low (1) 0 - 7,500 /min Overall length 182 mm (7-1/8") Rated voltage D.C.
4. 5. 6. 7. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
Follow your local regulations relating to disposal of battery. 11. Symbols SAVE THESE INSTRUCTIONS. The followings show the symbols used for tool. CAUTION: Only use genuine Makita batteries. Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and charger.
To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge. NOTE: Depending on the conditions of use and the ambient temperature, the indication may differ slightly from the actual capacity. To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Insert it all the way until it locks in place with a little click.
Switch action NOTE: When the tool is overheated, the tool stops automatically and the lamp starts flashing. In this case, release the switch trigger. The lamp turns off in one minute. NOTE: Use a dry cloth to wipe the dirt off the lens of the lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination. Reversing switch action 1 ► 1.
CAUTION: Always set the speed change lever fully to the correct position. If you operate the tool with the speed change lever positioned halfway between the "1" side and "2" side, the tool may be damaged. 2 CAUTION: Do not use the speed change lever while the tool is running. The tool may be damaged. Displayed Number Speed Torque Applicable operation 1 Low High Heavy loading operation 2 High Low Light loading operation 1 3 4 ► 1. Action mode changing ring 2. Adjusting ring 3.
Installing driver bit holder ASSEMBLY Optional accessory CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. 1 Installing or removing driver bit/ drill bit Optional accessory 2 1 3 ► 1. Driver bit holder 2. Driver bit 2 Fit the driver bit holder into the protrusion at the tool foot on either right or left side and secure it with a screw. When not using the driver bit, keep it in the driver bit holders.
Screwdriving operation Drilling operation First, turn the action mode changing ring so that the arrow points to the marking. Then proceed as follows. CAUTION: Adjust the adjusting ring to the proper torque level for your work. CAUTION: Make sure that the driver bit is inserted straight in the screw head, or the screw and/or driver bit may be damaged. Drilling in wood First, turn the action mode changing ring so that the arrow on the tool body points to the marking.
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo: Capacidades de taladrado XPH12 Mampostería 13 mm (1/2") Acero 13 mm (1/2") Madera Capacidades de fijación 38 mm (1/1/2") Tornillo para madera 10 mm x 90 mm (3/8" x 3-1/2") Tornillo de máquina 6 mm (1/4") Velocidad sin carga (RPM) Alta (2) 0 - 2 000 r/min Baja (1) 0 - 500 r/min Golpes por minuto Alto (2) 0 - 30 000 gpm Bajo (1) 0 - 7 500 gpm Longitud total 182 mm (7-1/8") Tensión nominal 18 V c.c.
Seguridad personal 1. Manténgase alerta, preste atención a lo que está haciendo y utilice su sentido común cuando opere una herramienta eléctrica. No utilice una herramienta eléctrica cuando esté cansado o bajo la influencia de drogas, alcohol o medicamentos. Un momento de distracción mientras opera las herramientas eléctricas puede terminar en una lesión grave. 2. Use equipo de protección personal. Póngase siempre protección para los ojos.
3. 4. 5. 6. 7. 8. 9. 10. Sujete la herramienta eléctrica por las superficies de agarre aisladas al realizar una operación en la que el accesorio de corte pueda estar en contacto con cables ocultos. Si el accesorio de corte entra en contacto con un cable con corriente, las piezas metálicas expuestas de la herramienta eléctrica se cargarán también de corriente y el operario podrá recibir una descarga eléctrica.
Consejos para alargar al máximo la vida útil de la batería Cargue el cartucho de batería antes de que se descargue completamente. Pare siempre la operación y cargue el cartucho de batería cuando note menos potencia en la herramienta. No cargue nunca un cartucho de batería que esté completamente cargado. La sobrecarga acortará la vida de servicio de la batería. Cargue el cartucho de batería a una temperatura ambiente de 10 °C - 40 °C (50 °F - 104 °F).
Accionamiento del interruptor NOTA: Dependiendo de las condiciones de uso y la temperatura ambiente, la indicación podrá diferir ligeramente de la capacidad real. Sistema de protección para la herramienta/batería La herramienta está equipada con un sistema de protección de la herramienta/batería. Este sistema corta en forma automática el suministro de energía al motor para prolongar la vida útil de la herramienta y la batería.
NOTA: Cuando la herramienta se sobrecaliente, ésta se detendrá automáticamente y la lámpara comenzará a destellar. En este caso, suelte el gatillo interruptor. La lámpara se apagará en un minuto. NOTA: Utilice un paño seco para quitar la suciedad de la lente de la lámpara. Tenga cuidado de no rayar la lente de la lámpara ya que la iluminación podría disminuir.
Esta herramienta cuenta con tres modos de accionamiento. • Modo de taladrado (rotación solamente) • Modo de taladrado y martilleo (rotación con percusión) Modo de atornillado (rotación con embrague) • Seleccione el modo apropiado para el trabajo en cuestión. Gire el anillo de cambio de modo de accionamiento y alinee la marca que haya seleccionado con la flecha en el cuerpo de la herramienta. Ajuste de la torsión de apriete La torsión de apriete puede ajustarse en 21 niveles girando el anillo de ajuste.
Instalación del gancho OPERACIÓN PRECAUCIÓN: Siempre inserte completamente el cartucho de batería hasta que quede asegurado en su lugar. Si puede ver el indicador rojo del lado superior del botón, esto indica que no ha quedado completamente asegurado. Insértelo por completo hasta que el indicador rojo no pueda verse. De lo contrario, podría salirse accidentalmente de la herramienta y ocasionarle lesiones a usted o a alguien a su alrededor.
Taladrado en metal Operación de taladrado con percusión Para evitar que la broca de taladro resbale una vez que comience a hacer el orificio, haga un surco con punzón y un martillo en el punto a taladrar. Coloque la punta de la broca de taladro en el surco y comience a taladrar. Utilice un lubricante para corte cuando taladre metales. Salvo en el caso de hierro y bronce, los cuales deberán ser taladrados en seco.
ACCESORIOS OPCIONALES PRECAUCIÓN: Estos accesorios o aditamentos están recomendados para utilizarse con su herramienta Makita especificada en este manual. El empleo de cualquier otro accesorio o aditamento puede conllevar el riesgo de lesiones personales. Utilice los accesorios o aditamentos solamente para su fin establecido. Esta garantía le concede derechos legales específicos y usted podrá tener también otros derechos que varían de un estado a otro.
21
22
23
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.