INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES Cordless Recipro Saw Sierra Recíproca Inalámbrica XRJ04 IMPORTANT: Read Before Using. IMPORTANTE: Lea antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model: XRJ04 Length of stroke 32 mm (1-1/4″) Strokes per minute Max. cutting capacities 0 - 2,800 /min Pipe 130 mm (5-1/8″) Wood 255 mm (10″) Rated voltage D.C. 18 V Standard battery cartridge BL1815N, BL1820, BL1820B Overall length 486 mm (19-1/8″) Net weight • • • BL1830, BL1830B, BL1840, BL1840B, BL1850, BL1850B, BL1860B 3.5 kg (7.6 lbs) 3.8 kg (8.
7. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. 2. 3. Power tool use and care 1. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. 2. Do not use the power tool if the switch does not turn it on and off.
Symbols CAUTION: Only use genuine Makita batteries. Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and charger. The followings show the symbols used for tool. volts direct current Tips for maintaining maximum battery life no load speed 1. revolutions or reciprocation per minute 2. Important safety instructions for battery cartridge 1. 2. 3.
To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge. Indicating the remaining battery capacity To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Insert it all the way until it locks in place with a little click. If you can see the red indicator on the upper side of the button, it is not locked completely.
1 1 2 B A 2 ► 1 . Lock-off button 2. Switch trigger 3 ► 1 . Blade clamp lever 2. Released position 3. Fixed position To prevent the switch trigger from accidentally pulled, the lock-off button is provided. To start the tool, depress the lock-off button from B side and pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop. After use, always press in the lock-off button from A side.
MAINTENANCE CAUTION: Keep hands and fingers away from the lever during the switching operation. Failure to do so may cause personal injuries. CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. NOTE: If you remove the recipro saw blade without rotating the blade clamp lever fully, the lever may not be locked in the released position .
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo: XRJ04 Extensión de la carrera 32 mm (1-1/4″) Carreras por minuto Capacidad máxima de corte 0 - 2 800 cpm Tubo 130 mm (5-1/8″) Madera 255 mm (10″) Tensión nominal 18 V c.c.
2. 3. 4. 5. 6. 7. Use equipo de protección personal. Póngase siempre protección para los ojos. El equipo protector tal como máscara contra el polvo, zapatos de seguridad antiderrapantes, casco rígido y protección para oídos utilizado en las condiciones apropiadas reducirá el riesgo de lesiones. Impida el encendido accidental.
3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Use siempre gafas de seguridad o protectoras. Los anteojos comunes o para el sol NO son gafas de seguridad. Evite cortar clavos. Revise la pieza de trabajo y quite todos los clavos antes de utilizar la herramienta. No corte piezas de trabajo demasiado grandes. Compruebe que hay espacio suficiente más allá de la pieza de trabajo antes de cortar para que el disco no golpee el suelo, el banco de trabajo, etc. Sujete la herramienta con firmeza.
PRECAUCIÓN: Utilice únicamente baterías originales de Makita. El uso de baterías no originales de Makita, o de baterías alteradas, puede ocasionar que las baterías exploten causando un incendio, lesiones personales y daños. Asimismo, esto invalidará la garantía de Makita para la herramienta y el cargador Makita. 1 2 Consejos para alargar al máximo la vida útil de la batería 1. 2. 3. 4. Cargue el cartucho de batería antes de que se descargue completamente.
Sobrecarga: La herramienta se está utilizando de una manera que causa que consuma una cantidad de corriente inusualmente alta. En este caso, apague la herramienta y detenga la aplicación que causó que la herramienta se sobrecargara. Luego encienda la herramienta para reiniciarla. Si la herramienta no arranca, significa que la batería se sobrecalentó. En este caso, espere a que la batería se enfríe antes de volver a encender la herramienta.
Para instalar la segueta recíproca, asegúrese siempre de que la palanca de la abrazadera de la segueta (parte del manguito de la abrazadera de la segueta) esté en en la cubierta de aislamiento la posición liberada antes de insertar la segueta recíproca. Si la palanca de la abrazadera de la segueta se encuentra en la posición fija, gírela en la dirección de la flecha para que pueda ser trabada en la posición liberada . 2 1 1 ► 1 . Segueta recíproca 2.
1 ► 1 . Tapa del portaescobillas MANTENIMIENTO PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería extraído antes de intentar realizar una inspección o mantenimiento. 3. Inserte el cartucho de batería en la herramienta y haga el rodaje de las escobillas poniendo a funcionar la herramienta sin carga durante 1 minuto aproximadamente. 4. Revise la herramienta mientras está funcionando y la operación del freno eléctrico cuando suelte el gatillo interruptor.
GARANTÍA LIMITADA DE UN AÑO DE MAKITA Ésta Garantía no aplica para México Política de garantía Cada herramienta Makita es inspeccionada y probada exhaustivamente antes de salir de la fábrica. Se garantiza que está libre de defectos de mano de obra y materiales por el período de UN AÑO a partir de la fecha original de compra. Si durante este período de un año se desarrollara algún problema, devuelva la herramienta COMPLETA, con el envío prepagado, a un centro de servicio autorizado o de fábrica Makita.
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
DC18RA DC18RC Fast Charger Chargeur rapide Cargador rápido Symbols The followings show the symbols used for the charger and battery. Be sure that you understand their meaning before use. Symboles Nous donnons ci-dessous les symboles utilisés pour le chargeur et la batterie. Assurez-vous que vous en avez bien compris la signification avant d’utiliser l’outil. Símbolos A continuación se muestran los símbolos utilizados con el cargador y la batería. Asegúrese de que entiende su significado antes de usarla.
• Do not short batteries. • Ne jamais court-circuiter les bornes d’une batterie. • No provoque un cortocircuito en las baterías. IMPORTANT: Read Before Using. IMPORTANT : Lire ce qui suit avant d’utiliser cet outil. IMPORTANTE: Leer antes de usar.
ENGLISH Specifications Model DC18RA Input DC18RC A.C. 120 V 50 – 60 HZ Output Weight D.C. 7.2 V – 18 V 0.88 kg (1.94 lbs) 0.77 kg (1.70 lbs) • Manufacturer reserves the right to change specifications without notice. • Note: Specifications may differ from country to country. • Weight according to EPTA-Procedure 01/2003. IMPORTANT SAFETY INSTRUCTIONS CAUTION: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.
5. With finish of charge, the green light remains lit with the red light going out and the melody sound preset at the insertion of battery cartridge or buzzer sound (a long beep) comes out to notify completion of charge. (In selected silent mode, no sounds come out.) 6. Preset melody sound remains stored even when the charger is unplugged. NOTE: • The battery charger is for charging Makita-battery cartridge. Never use it for other purposes or for other manufacturer’s batteries.
FRANÇAIS Spécifications Modèle Entrée DC18RA DC18RC C.A. 120 V 50 – 60 Hz Sortie Poids C.C. 7,2 V – 18 V 0,88 kg (1,94 lbs) 0,77 kg (1,70 lbs) • Le fabricant se réserve le droit de modifier sans avertissement les spécifications. • Remarque : Les spécifications peuvent varier selon les pays. • Poids selon la procédure EPTA 01/2003. LES CONSIGNES DE SECURITE IMPORTANTES ATTENTION : 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.
Changer la mélodie de charge terminée 1. Lorsque vous insérez la batterie dans le chargeur, le chargeur émet la dernière courte mélodie préréglée d’indication de charge terminée. 2. Si vous retirez et réinsérez la batterie dans les cinq secondes qui suivent cette action, la mélodie changera. 3. Chaque fois que vous retirez et réinsérez la batterie dans les cinq secondes par la suite, la mélodie change dans l’ordre préétabli. 4.
Tension 9,6 V 12 V 14,4 V Nombre de cellules 8 10 12 Cartouche de batterie au Ni-MH Capacité (Ah) Temps de charge (en minutes) 20 — — — 1,7 BH9020A — — 2,0 20 — BH1220/C BH1420 2,0 15 20 — — — 2,7 BH9033A — — 3,3 30 — BH1233/C BH1433 3,3 22 Tension 14,4 V 18 V 14,4 V 18 V Nombre de cellules 4 5 8 10 Cartouche de batterie au Li-ion BL1415 BL1815 — — 15 — — BL1430 BL1830 22 Temps de charge (en minutes) Note : • La charge complète peut prendre jusqu’
ESPAÑOL Especificaciones Modelo DC18RA 120 V Entrada Salida Peso DC18RC 50 – 60 Hz 7,2 V cc – 18 V cc 0,88 kg (1,94 lbs) 0,77 kg (1,70 lbs) • El fabricante se reserva el derecho a cambiar las especificaciones sin aviso. • Nota: Las especificaciones podrán cambiar de un país a otro. • Peso de acuerdo con el procedimiento EPTA 01/2003. INSTRUCCIONES DE SEGURIDAD IMPORTANTES PRECAUCION: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.
Cambio de la melodía de carga terminada 1. 2. 3. 4. Al insertar el cartucho de batería en el cargador se emite el último sonido de melodía breve programado. El sonido de melodía puede cambiarse extrayendo y reinsertando antes de cinco segundos el cartucho de batería. Cada vez que se extraiga y reinserte antes de otros cinco segundos, el sonido de melodía cambiará en orden. Cuando se emita el sonido de melodía deseado, deje el cartucho de batería insertado y comenzará la carga.
Tensión 9,6 V cc 12 V cc 14,4 V cc Número de celdas 8 10 12 Capacidad (Ah) Cartucho de batería Ni-MH Tiempo de carga (minutos) — — — 1,7 Ah 20 min BH9020A — — 2,0 Ah 20 min — BH1220/C BH1420 2,0 Ah 15 min — — — 2,7 Ah 20 min BH9033A — — 3,3 Ah 30 min — BH1233/C BH1433 3,3 Ah 22 min Tensión 14,4 V cc 18 V cc 14,4 V cc 18 V cc Número de celdas 4 5 8 10 Cartucho de batería Li-ion BL1415 BL1815 — — 15 min — — BL1430 BL1830 22 min Tiempo de carga (min
11
Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 884676H946 IDE www.makita.