ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Rotary Hammer BHR200 003091 IMPORTANT: Read Before Using.
ENGLISH (Original instructions) SPECIFICATIONS Model Capacities BHR200 Concrete 20 mm Steel 13 mm Wood 27 mm No load speed (min-1) 0 - 1,100 Blows per minute 0 - 4,700 Overall length 316 mm Net weight 3.8 kg Rated voltage D.C. 24 V • Due to our continuing programme of research and development, the specifications herein are subject to change without notice. • Specifications and battery cartridge may differ from country to country.
ENH101-14 you to lose control. Electrical safety 4. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. 5. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. 6. Do not expose power tools to rain or wet conditions.
terminal to another. Shorting the battery terminals together may cause burns or a fire. 27. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. Service 28. Have your power tool serviced by a qualified repair person using only identical replacement parts.
11. 12. 13. 14. Do not leave the tool running. Operate the tool only when hand-held. Do not point the tool at any one in the area when operating. The bit could fly out and injure someone seriously. Do not touch the bit or parts close to the bit immediately after operation; they may be extremely hot and could burn your skin. Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data. exceed 50 ゚ C (122 ゚ F).
the tool, causing injury to you or someone around you. Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly. • Selecting the action mode Rotation with hammering 1 2 Switch action 1. Switch trigger 1. Rotation with hammering 2. Lock button 3. Pointer 4. Change lever 3 4 003128 1 For drilling in concrete, masonry, etc., depress the lock button and rotate the change lever so that the pointer points to the symbol.
CAUTION: Always use the side grip to ensure operating safety when drilling in concrete, masonry, etc. The side grip swings around to either side, allowing easy handling of the tool in any position. Loosen the side grip by turning it counterclockwise, swing it to the desired position and then tighten it by turning clockwise. Torque limiter The torque limiter will actuate when a certain torque level is reached. The motor will disengage from the output shaft. When this happens, the bit will stop turning.
Bit angle (when chipping, scaling or demolishing) 2 1 Dust cup 1. Dust cup 1. Change lever 2. O symbol 1 001300 Use the dust cup to prevent dust from falling over the tool and on yourself when performing overhead drilling operations. Attach the dust cup to the bit as shown in the figure. The size of bits which the dust cup can be attached to is as follows. 003170 1. Change lever 1 Dust cup 5 Dust cup 9 Bit diameter 6 mm - 14.
repeating this several times, the hole will be cleaned out and normal drilling may be resumed. • Use the optional drill chuck assembly. When installing it, refer to "Installing or removing the bit" described on the previous page. Set the change lever so that the pointer points to the symbol. You can drill up to 13 mm diameter in metal and up to 27 mm diameter in wood. Use a cutting lubricant when drilling metals. The exception is brass which should be drilled dry .
1 1. Brush holder cap 2. Screwdriver 2 003228 To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts. ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
Makita Corporation Anjo, Aichi, Japan 884305F220 12 www.makita.