Anale u - Cutter - - - ~ 255 mm (10”) MODEL 4110C INSTRUCTION MANUAL DOUBLE INSULATION SPECIFICAT10 NS Wheel diameter Max. cutting capacity 255 mm (10”) 75 mm (3”) AMPS (115 v1 No load speed AClDC 15 A 3r500 Overall length Net weight supply cord 620” (24.318“) 9 kg (19.8 Ibs) 2.5 m (8.2 ft.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. ~~~ ~~ 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools t o rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw.
VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user - as well as damage t o the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating is harmful to the motor. SAVE THESE INSTRUCTIONS.
Switch action To start the tool, simply pull the trigger. Release the trigger t o stop. How to cut The cut i s made by pulling the tool toward you (not by pushing away from you). Align the notch on the shaft of the safety guard with your cutting line when performing a cut. I / Notch (Groove) CAUTION : Use this tool for straight line cutting only.
Cutting depth adjustment 1. Loosen the wing bolt. 2. Obtain the desired cutting depth. 3. Tighten the wing bolt. I Base Securing safety guard The safety guard can be adjusted about 80 degrees, after you loosen the wing nut. Adjust to the desired angle, then secure the wing nut. I Wheel changes To replace the abrasive cut-off wheel, depress the shaft lock to hold the shaft stationary, then loosen the hex bolt with the socket wrench provided.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced a t the same time. Use only identical carbon brushes. I Use a screwdriver to remove the brush holder caps.
ACCESS0 R IES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Diamond wheel 255 (Dry type) Part No. 792290-6 For concrete, brick, concrete block, etc. 0 Abrasive cut-off wheel 305 (5 per pkg) Part No. 792301-7 For steel pipe, angle steel, light-weight steel, etc.
Oec-08-'94 US 255 mm (IO") CUTTER Model 4110C Note: The switch, noise suppressor and other part configurations may differ from country to country.
MACHINE - MACHINE ~ 1 2 3 4 5 6 14 15 16 17 18 19 20 21 22 23 24 25 26 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 4 1 1 1 1 1 1 1 1 1 3 1 1 1 1 1 1 1 1 Hex. Bolt M10x25 Inner Flange 100 Ring 20 Inner Flange 100 Safety cover Cap Square Neck Bolt M8x24 Grip Wing Nut M8 Spring Washer 8 Flat Washer 8 Lock Plate Countersunk Head Screw M5x8 Hex Bolt M8x16 Stop Ring E-9 Ring 12 Stop Ring E-9 Stop Ring E-9 Ring 12 Stop Ring E-9 Hex.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted t o be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.