ENGLISH: Original instructions INSTRUCTION MANUAL Construction Coil Nailer AN935H Read before use.
SPECIFICATIONS Model: AN935H Air pressure 1.28 - 2.26 MPa (12.8 - 22.6 bar) Nail length Wire-collated coil nail Nail capacity 45 mm - 90 mm Sheet-collated coil nail 45 mm - 75 mm Wire-collated coil nail 120 pcs - 300 pcs Sheet-collated coil nail 200 pcs Minimum hose diameter 4.0 mm Pneumatic tool oil ISO VG32 or equivalent Dimensions (L x W x H) 299 mm x 125 mm x 330 mm Net weight • • • 2.
Personal protective equipments 4. Always check contact element as instructed in this manual. Fasteners may be driven accidentally if the safety mechanism is not working correctly. Loading fasteners 1. Do not load the tool with fasteners when any one of the operating controls is activated. 2. Use only fasteners specified in this manual. The use of any other fasteners may cause malfunction of the tool. 1. 2. Always wear safety glasses to protect your eyes from dust or fastener injury.
8. 9. 10. 11. 12. 13. 14. 15. 16. 17. Do not activate the tool unless the tool is placed firmly against the workpiece. Never hold or carry the tool with a finger on the trigger or hand it to someone in this condition. Accidental firing can cause serious injury.
The air compressor must comply with the requirements of EN60335-2-34. FUNCTIONAL DESCRIPTION Select a compressor that has ample pressure and air output to assure cost-efficient operation. The graph shows the relation between nailing frequency, applicable pressure and compressor air output. Thus, for example, if nailing takes place at a rate of approximately 40 times per minute at a compression of 1.77 MPa (17.7 bar), a compressor with an air output over 100 liters/minute is required.
1 2 3 1 ► 1. Hook 4 ► 1. Nose adapter 2. Contact element 3. Protrusion 4. Recessed part Furthermore, this hook can be installed on either side of the tool. To change the installation position, remove the bolt with a hex wrench. Install the hook on another side and then secure it firmly with the bolt. Air duster CAUTION: Do not aim the ejection port of the air duster to someone. Also, keep your hands and foot away from the ejection port.
Then place the first nail in the nail rail and the second nail in the feed claw. Also, place other uncoiled nails on feeder body. Loading nailer CAUTION: Do not use deformed nails or linked sheet. 1. 2 Disconnect the air hose. 1 2. Depress the latch lever and open the door and magazine cap. ► 1. Nail rail 2. Feed claw 5. 3 1 Check that the nail coil is set properly in the magazine. 6. Close the magazine cap carefully.
The trigger for single sequential actuation mode is factory-installed. To change the nailing mode to contact actuation, replace the trigger part with the one for contact actuation. 4 2 1 1 3 ► 1. Trigger for contact actuation 2. Silver part 3. Trigger for single sequential actuation 4. Black part 1. Turn the trigger lock lever to the lock position . 2 ► 1. Hinged part 2. Rod of the valve 4. Insert the pin to the hole and secure it by urethane washer. 5.
— Single sequential actuation Make sure that the tool does not operate only by placing the contact element against the workpiece without pulling the trigger. Place the contact element against the workpiece and pull the trigger fully. After nailing, release the contact element, and then release the trigger. 3 1 2 2 1 ► 1. Contact element 2. Workpiece 3.
Nailing on steel plate Nailing on concrete WARNING: When nailing on the C-shaped steel, limit the thickness to 3.2 mm (1/8") or thinner. Otherwise the tool will bounce severely and a nail struck back, causing serious injuries. WARNING: Use hardened nails only for concrete. Using other purposed nails may cause serious injuries. plate. Using other purposed nails may cause serious injuries. WARNING: Do not nail directly on the concrete or do not fasten directly the steel plate to the concrete.
MAINTENANCE 1 CAUTION: Before attempting to perform inspection or maintenance, always lock the trigger by turning the trigger lock lever to the lock position , and disconnect the air hose from the tool. NOTICE: Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result. Cleaning of tool ► 1. Ejected linked sheet Iron dust that adhere to the magnet can be blown off by using an air duster.
OPTIONAL ACCESSORIES 1 CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. ► 1. Drain cock Keep the air hose away from heat (over 60°C, over 140°F), away from chemicals (thinner, strong acids or alkalis).