Wheel Slincien Equipped with Electric Brake MODEL 9741 INSTRUCTION MANUAL SPECIFICATIONS Wheel size (Diameter x Width) No load speed 100 mm x 120 mm (4” x 4.314”) 3,500 (RPM) Dimensions (L x W x H) Net weight 310 mm x 185 mm x 182 mm 112-1/4” x 7-1/4” x 7-118”) 4,2 kg (9,2 lbsl Manufacturer reserves the right t o change specifications without notice. Note: Specifications may differ from country t o country.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools t o rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don't operate tool when you are tired. 18.
ADDITIONAL SAFETY RULES 1. Inspect for and remove foreign matter such as nails, screws, etc. from the workpiece surface before operation. 2. Do not wear gloves during operation. 3. Hold the tool firmly w i t h both hands. 4. Keep hands away from rotating parts. 5. Do not leave the tool running. Operate the tool only when hand-held. 6. Never attempt t o use w i t h the tool held upside down in a vise, etc. SAVE THESE INSTRUCTIONS.
Removing or installing wheel CAUTION : Always be sure that the tool is switched off and unplugged before removing or installing the wheel. To remove the wheel, insert one hex wrench into the end of the spindle and another hex wrench into the end of the output shaft. Turn the hex wrench in the output shaft clockwise while securely holding the hex wrench in the spindle so that the wheel cannot revolve. Pull the output shaft out from the wheel.
Connecting t o dust collector (Optional accessory) The use of a dust collector makes sanding operations clean and dust collection easy. To connect a dust collector, open the dust port by sliding the cover plate up and in a clockwise direction. Attach the joint onto the dust port. Now a dust collector can be connected t o this tool. CAUTION : When not using a dust collector, close the dust port opening with the cover plate. . Switch action To start the tool, simply pull the trigger.
Operation Hold the tool firmly with both hands on the handle and the grip in front. Place the tool on the workpiece surface and move the tool gently forward and backward while applying slight downward pressure. CAUTION : *The tool should not be in contact with the workpiece surface when you turn the tool on or off. Damage to the tool or the workpiece surface and injury to the operator may resuIt. Apply slight downward pressure only.
MAINTENANCE CAUTION: Always be sure that the tool i s switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced a t the same time. Use only Makita carbon brushes. Limit mark Use a screwdriver to remove the brush holder caps.
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Hex wrench Part No. 783204-6 Joint Part No. 41 0899-9 Nylon brush wheel Part No.
WHEEL SANDER Model 9741 Q Note: The switch, noise suppressor and other part configurations may differ from country to country.
om -28-'88 MODEL 9741 $zD ~ Ball Bearing 6001LLB Flat Washer 12 Helical Gear 53 Retaining Ring S - 15 Ball Bearing 6OOZDDW Spindle 34 35 36 37 38 39 40 41 42 1 1 1 1 1 2 2 1 1 Wing Nut M 6 Flat Washer 6 Depth Guide Stop Ring E - 5 Name Plate Brush Holder Cap Carbon Brush Pan Head Screw M 4 Thin Washer 6 Key 4 43 1 cover Plate Gear Housing Pan Head Screw M5x14 Grip Wheel Bearing Retainer 44 Ball Bearing 6003DDW Countersunk Head Screw M4x14 Insulation Washer Ball Bearing 608LL8 Rubber Pin 4 ARMATUR
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thorou ly inspected and tested before leaving the factory. It is warranted t o be free of defects from w o r k a s h i p and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
