Angle Grinder 150 mm (6”) MODEL 9566CV 004051 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. w w w. m a k i t a t o o l s.
SPECIFICATIONS Model 9566CV No load speed (RPM) 4,000 - 9,000/min Overall length 299 mm (11-3/4”) Net weight 1.8 kg (4.0 lbs) Spindle thread 5/8” • Manufacturer reserves the right to change specifications without notice. • Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.
5. Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. 6. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 7. Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately.
USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table 1 shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.
12. Make sure cord is clear of wheel. Do not wrap cord around your arm or wrist. If control of tool is lost, cord may become wrapped around you and cause personal injury. 17. Do not leave the tool running. Operate the tool only when hand-held. 13. Make sure the wheel is not contacting the workpiece before the switch is turned on. 19. ALWAYS wear proper apparel including long sleeve shirts, leather gloves and shop aprons to protect skin from contact with hot grindings. 14.
FUNCTIONAL DESCRIPTION • 004052 CAUTION: Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Shaft lock • CAUTION: Never actuate the shaft lock when the spindle is moving. The tool may be damaged. Press the shaft lock to prevent spindle rotation when installing or removing accessories. 1 1. Shaft lock 001035 Switch action O 1 • • 1.
001046 The rotating speed can be changed by turning the speed adjusting dial to a given number setting from 1 to 5. Higher speed is obtained when the dial is turned in the direction of number 5. And lower speed is obtained when it is turned in the direction of number 1. Refer to the table for the relationship between the number settings on the dial and the approximate rotating speed. 2 1 1.
004053 Installing side grip (handle) • CAUTION: Always be sure that the side grip is installed securely before operation. Screw the side grip securely on the position of the tool as shown in the figure. 004054 Installing or removing abrasive cut-off wheel 1 2 • 3 4 5 1. 2. 3. 4. 5.
002981 1 Loosen the lever on the wheel guard. Mount the wheel guard with the protrusion on the wheel guard band aligned with the notch on the bearing box. Then rotate the wheel guard around 180 degrees. Tighten the lever to fasten the wheel guard. If the lever is too tight or too loosen to fasten the wheel guard, loosen or tighten the screw to adjust the tightening of the wheel guard band. To remove wheel guard, follow the installation procedure in reverse. 1.
001107 1 Installing or removing abrasive disc (optional accessory) 2 3 NOTE: • 1. Lock nut 2. Abrasive disc 3. Rubber pad Use sander accessories specified in this manual. These must be purchased separately. Mount the rubber pad onto the spindle. Fit the disc on the rubber pad and screw the lock nut onto the spindle. To tighten the lock nut, press the shaft lock firmly so that the spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise.
Grinding and sanding operation (optional accessory) A 002983 ALWAYS hold the tool firmly with one hand on housing and the other on the side handle. Turn the tool on and then apply the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an angle of about 15 degrees to the workpiece surface. During the break-in period with a new wheel, do not work the grinder in the B direction or it will cut into the workpiece.
Unplug tool and place it upside down allowing easy access to spindle. Remove any accessories on spindle. Thread wire wheel brush onto spindle and tighten with the wrenches. When using wire wheel brush, avoid applying too much pressure which causes over bending of wires, leading to premature breakage. MAINTENANCE 002985 • 1 2 1. Exhaust vent 2. Inhalation vent CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance.
002986 1 2 6 3 7 2 11 12 9 8 10 13 4 14 5 15 9566CV 1 Grip 36 2 Wheel guard 3 Inner flange 82 4 Depressed center grinding wheel / Multi-disc 5 Lock nut 5/8-45 6 Rubber pad 125 7 Abrasive disc 8 Sanding lock nut 5/8-48 9 Wire wheel brush 10 Wire cup brush 11 Wheel guard (For cut-off wheel) 12 Inner flange 48 13 Spacer 14 Cut-off wheel 15 Lock nut 5/8-48 - Lock nut wrench 28 13
Memo 14
Memo 15
Memo 16
Cut First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc.
MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: Home Center 3. How did you learn about this product: Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( Other ( ) 2. Use of the product is intended for: ) 4.
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 FLORIDA 750 East Sample Road Pompano Beach, FL 33064 (954) 781-6333 MISSOURI 9876 Watson Road St. Louis, MO 63126-2221 (314) 909-9889 PENNSYLVANIA 1704 Babcock Blvd. Pittsburgh, PA 15209 (412) 822-7370 CALIFORNIA 41850 Christy St. Fremont, CA 94538-5107 (510) 657-9881 GEORGIA 4680 River Green Parkway NW Duluth, GA 30096 (770) 476-8911 NEBRASKA 4129 S.
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work.