ENGLISH (Original instructions) INSTRUCTION MANUAL Angle Grinder 9556HN 9557HN 9558HN 005801 DOUBLE INSULATION IMPORTANT: Read Before Using.
ENGLISH (Original instructions) SPECIFICATIONS Model 9556HN 9557HN 9558HN Depressed center wheel diameter 100 mm 115 mm 125 mm Spindle thread M10 M14 M14 Rated speed (n) / No load speed (no) 11000 min-1 11000 min-1 11000 min-1 Overall length 271 mm 271 mm 271 mm Net weight 1.9 kg 2.0 kg 2.1 kg Safety class /II • Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
For Model 9558HN Makita International Europe Ltd. Michigan Drive, Tongwell, Milton Keynes, Bucks MK15 8JD, England ENG102-3 Noise The typical A-weighted noise level determined according to EN60745: Sound pressure level (LpA) : 86 dB(A) Sound power level (LWA) : 97 dB(A) Uncertainty (K) : 3 dB(A) Wear ear protection 30.1.
19. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. 20. Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. 21.
3. 4. 5. 6. 7. 8. 9. 10. hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and shock the operator. 11. Position the cord clear of the spinning accessory. If you lose control, the cord may be cut or snagged and your hand or arm may be pulled into the spinning accessory. 12. Never lay the power tool down until the accessory has come to a complete stop.
c) Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in direction opposite to the wheel’s movement at the point of snagging. d) Use special care when working corners, sharp edges etc. Avoid bouncing and snagging the accessory. Corners, sharp edges or bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback. e) Do not attach a saw chain woodcarving blade or toothed saw blade.
21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. Before using the tool on an actual workpiece, let it run for a while. Watch for vibration or wobbling that could indicate poor installation or a poorly balanced wheel. Use the specified surface of the wheel to perform the grinding. Watch out for flying sparks. Hold the tool so that sparks fly away from you and other persons or flammable materials. Do not leave the tool running. Operate the tool only when hand-held.
When using an abrasive cut-off / diamond wheel, be sure to use only the special wheel guard designed for use with cut-off wheels. (In European countries, when using a diamond wheel, the ordinary guard can be used.) Mount the wheel guard with the protrusion on the wheel guard band aligned with the notch on the bearing box. Then rotate the wheel guard to such an angle that it can protect the operator according to work. Be sure to tighten the screw securely.
Operation with abrasive cut-off / diamond wheel (optional accessory) OPERATION • • • • • • WARNING: It should never be necessary to force the tool. The weight of the tool applies adequate pressure. Forcing and excessive pressure could cause dangerous wheel breakage. ALWAYS replace wheel if tool is dropped while grinding. NEVER bang or hit grinding disc or wheel onto work. Avoid bouncing and snagging the wheel, especially when working corners, sharp edges etc.
0 mm (4") Abrasive cut-off wheel Thickness: Less than 4 mm (5/32") Thickness: 4 mm (5/32") or more Diamond wheel Thickness: Less than 4 mm (5/32") 1 Thickness: 4 mm (5/32") or more 1 2 4 16 mm (5/8") 16 mm (5/8") 20 mm (13/16") 20 mm (13/16") 3 1. Lock nut 3 2. Abrasive cut-off wheel 3. Inner flange 4.
1. Exhaust vent 2. Inhalation vent 1 2 005809 The tool and its air vents have to be kept clean. Regularly clean the tool's air vents or whenever the vents start to become obstructed. To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts.
Makita Corporation Anjo, Aichi, Japan 884836C229 12 www.makita.
