Disc Grinder 125 mm (5") MODEL 9505BH INSTRUCTION MANUAL DOUBLE INSULATION SPEC IF ICAT IONS No load speed ~~~ .. iRPMi Overall length 10.000 2 6 0 mtn 110 1 4") Net weight Spindle thread 2 1 kg 14.
lMPORTANT SAFETY INSTRUCTlONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools t o rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONALSTARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure t o use one heavy enough t o carry the current your product will draw.
VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY t o the user - as well as damage t o the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating is harmful t o the motor. ADDITIONAL SAFETY RULES 1. Keep guards in place. 2.
Installing side grip (auxiliary handle) Screw the side grip on the tool securely. The side grip can be installed on either side of the tool, whichever is convenient. I 1 Installing or removing depressed center wheel CAUTION : Always be sure that the tool i s switched off and unplugged before installing or removing the wheel. Mount the inner flange onto the spindle. Fit the wheel on over the inner flange and screw the lock nut orito the spindle.
Switch action Slide the slide switch forward to start, and the switch will lock in the "ON" position. To stop, lgihtly depress the rear of the switch, and it will return to the "OFF" position. Slide switch CAUTION : Before plugging in the tool, always check to see that the switch actuates properly and returns to the "OFF" position when depressed. Operation Hold the tool firmly. Turn the tool on and then apply the wheel or disc to the workpiece.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced a t the same time. Use only identical carbon brushes. Use a screwdriver t o remove the brush holder caps.
ACCESSORIES CAUTION : These accessoires or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Wheel cover Part No. 164556-8 @ Depressed center wheels (5 wheels per pkg) 8 @ Inner flange 82 Part No. 224178-7 @ Lock nut 5/8-40 Part No.
0 Multi disc I Part No. 794331 -4A 794331- 4 8 I Size (mm) Grit 125 x 17 x 22.2 794331 -4D 100 @ @ Abrasive discs (5discs per pkg) Locknut 5 / 8 - 4 8 (For abrasive disc) Part No. 224517-1 8 Urethane washer 14 Part No. 261039-0 Part No. 742072-A-5 742073-A-5 742074-A-5 742075-A-5 742076-A-5 0 Grip 2 6 Part No. 273485-5 0 Steel carrying case Part No. 181717-5 Grit 24 30 50 80 120 When using wire brush, mount urethane wahser 14 t o the spindle.
Sep 2 2 ' 8 7 US 125 mm (5") DISC GRINDER Model 9505BH Note: The switch and other part configurations may differ from country to country.
MODEL 9 5 0 5 E H ITEM NO NO USED Sep DESCRIPTION I:,'," ,":, DESCRIPTION MACHIN! 1 2 3 4 5 4 1 7 1 1 1 1 1 8 2 9 1 1 1 1 1 2 6 10 11 12 13 16 17 18 19 20 21 22 24 25 1 1 1 2 2 1 1 1 - Pan Head Srrew M 4 x 2 0 1With Wa
P MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from worbnanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.