n 115 mm (4-1/2”) MODEL 9503BH INSTRUCTION MANUAL No load speed (RPM) Overall length Net weight Spindle thread 10,000 260 mm (10-114”) 2 kg (4.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools t o rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don't operate tool when you are tired. 18.
ADDITIONAL SAFETY RULES . 1. Keep guards in place. 2. Use only wheels having a maximum operating speed at least as high as “No Load RPM” marked on the tool‘s nameplate. When using depressed center wheels, be sure t o use only fiberglass-reinforced wheels. 3. Check the wheel carefully for cracks or damage before operation. Replace cracked or damaged wheel immediately. 4. Use only flanges specified for this tool. 5.
Installing side grip (auxiliary handle) Screw the side grip on the tool securely. The side grip can be installed on either side of the tool, whichever is convenient. 5 Installing or removing depressed center wheel CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the wheel. Mount the inner flange onto the spindle. Fit the wheel on over the inner flange and screw the lock nut onto the spindle.
Switch action Slide the slide switch forward to start, and the switch will lock in the "ON" position. To stop, lgihtly depress the rear of the switch, and it will return to the "OFF" position. Slide switch 7 CAUTION : Before plugging in the tool, always check to see that the switch actuates properly and returns to the "OFF" position when depressed. Operation Hold the tool firmly. Turn the tool on and then apply the wheel or disc to the workpiece.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when tehy wear down to about 4.5 mm (3/16") or less. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced a t the same time. Use only Makita carbon brushes. Use a screwdriver to remove the brush holder caps.
. ACC ESSOR I ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injuty t o persons. The accessories or attachments should be used only in the proper and intended manner. @ Wheel cover @ Inner flange 82 Part No. 224178-7 @ Lock nut 5/8-40 Part No. 224509-0 Part No. 164751-0 @ Depressed center wheels Part NO.
0 Abrasive discs @ ( 1 0 disc per pkg) Part No. 742082- 3 742083- 1 742084- 9 742085- 7 742086-5 Grip 26 Part No. 273485-5 0 Lock nut 5/8-48 (For abrasive disc) Part No. 22451 7- 1 Grit 24 30 50 80 120 0 Lock nut wrench 28 Part No. 782413-4 Steel carrying case Part No.
Oci - 0 8 ' 8 7 US 115 mm (4-1/2") DISC GRINDER Model 9503BH Note: The switch and other part configurations may differ from country to country.
o c t -08 ‘ 8 7 MODEL 9503BH ‘YE $iD DESCRIPTION ‘ktM AtD us DESCRIPTION MACHINE ~ 1 2 3 4 4 Pan Head Screw M4xZO IWith Washer) Spiral Bevel Gear 11 Ball Bearing 6000LB 26 27 28 Plate 29 5 1 1 1 1 6 1 7 8 2 30 31 32 33 34 9 1 1 1 1 2 1 1 1 2 1 1 Fan 60 ARMATURE ASSEMBLY IWith Item 5 8 8 & 91 Hex Bolt M4x70 (With Washer) InSUIetiOn Washer Ball Bearing 627LB FIELD ASSEMBLY Motor Housing Rubber Pin 4 Pan Head Screw M4x60 [With Washer) Cord Rear Cover Cord Guard Pan Head Screw M4x8 IWiIh
MAKITA LIMITEDONE YEAR WARRANTY Warranty Policy Every Makita tool is thorou ly inspected and tested before leaving the factory. It is warranted to be free of defects from w o r f k k s h i p and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.