Bench Grinder 125 mm (5") MODEL 9300 INSTRUCTION MANUAL SPECIFICATI0 NS Wheel size 1 Hz 1 No load speed 1 Overall length * Manufacturer reserves the right t o change specifications without notice. Note: Specifications may differ from country t o country.
For Your Own Safety Read Instruction Manual Before Operating BENCH GRINDER I GENERAL SAFETY PRECAUTIONS (For All Tools) 1. KNOW YOUR POWER TOOL. Read the owner's manual carefully. Learn the tools applications and limitations, as well as the specific potential hazards peculiar t o it. 2. KEEP GUARDS IN PLACE and in working order. 3. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 4. KEEP WORK AREA CLEAN.
17. USE RECOMMENDED ACCESSORIES. Consult the owner's manual for recommended accessories. The use of improper accessories may cause risk of injury t o persons. 18. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. 19. CHECK DAMAGED PARTS.
GROUNDING INSTRUCTIONS ALL GROUNDED, CORD-CONNECTED TOOLS: In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current t o reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.
ADDITIONAL SAFETY RULES FOR BENCH GRINDER 1. Be sure that the guards are in place t o protect the operator against flying debris and injury in case the wheel breaks. 2. Check the wheel for cracks and chipped edges before mounting and/or running it. Stand away from the front of the wheel and run for more than one minute t o test it. Replace if you note anything abnormal. Then test new wheel for more than 3 minutes. 3. Use only the face of a straight wheel and the side of a cup wheel when grinding.
14. Adjust tool rests so they are within 1 m m (1132") - 3 m m (118") of the grinding wheel. Height of tool rests should be so that are level with the middle (center) of the wheels. 15. Always keep the clearance between the face of a straight wheel and the adjust plate less than 1.6 m m (1116"). With a cup wheel, the adjust cover should be within 1 m m (1132") - 3 m m (118") from the wheel surface. This will prevent bodily harm should the wheel fly apart and or something become caught inside. 16.
NAMES OF PARTS Shaft lock Grinding wheel I Thumb screw C BEFORE USE 1. The eyeshields are packed together with the bench grinder. Always install the eyeshields before operation (see explanatory figure). 2. Fit eyeshields in between wheel cover and adjust plate (fitting small screws into installation holes on eyeshields). Secure tightly with P. H. screws. '\\ Eyeshleld - _ plate _ .
HOW TO USE Keep the space between the adjust plate and grinding wheel under 1.6 mm (1/16"). Screw in securely the (+) P. H. screws as soon as you have adjusted the adjust plate. (+) P. H. Screw Under 1 6 m Installing and removing the grinding wheel 1. Use a (+) screwdriver to remove the P. H. screws from the side cover.
Sharpening planer blade 1. How to fit planer blade holder set In the case of fitting the planer blade to the slider, two thumb screws of planer blade holder should be tightened so that the slider should always be contacted closely with the blade gauge A side, and the edge of blade should be contacted with i t s gauge 6 side. Thumb screw M5 x 10 r I4 1 I] 1 q Blade Ease gauge / \ aauae A side Blade gauge E side Slider 2.
Assembling circular saw sharpening kit 1. First install fixed rod with cross point into hole in the inclining tool rest. Secure with thumb screw B so that screw end fits into indentation on the rod. 2. Now slide rod for mounting saw blade holder and set nut into hole below on cross point. Secure with thumb screw. Note flat side of rod should be on the bottom. Set blade holder for circular saw into hole for it on sliding rod. Then set nut screws into the blade holder hole. Actual sharpening procedure 1.
2. Loosen thumb screws and move blade in closer to the grinding wheel. Make sure blade lies flat on top of the inclining tool rest. Secure thumb screws. 3. Using the two adjust screws (6,C) on the right side, work the sliding rod sideways until the tip of the saw blade just contacts the side of the grinding wheel. Secure blade with adjust screws so that uniform stock (teeth tips) removal will result. 3.
5. Keep a clearance of approximately 2mm (3/32") between the wheel and the blade teeth for turning. Secure thumb screw. Next, draw blade up to wheel so that the wheel is well into the tooth gullet. Use adjust screws (B, C) for fixed setting that will assure uniform gullet depth when sharpening. I Y 6. To obtain the original bevel angle or an angle of 15 degrees, release the thumb screw below on the inclining tool rest. Tilt rest to desired angle and secure with thumb screw.
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Grinding wheels Saw blade sharpening kit Part No. 122174-8 Sire (mml 125 15.J x 1 3 11/29x 12.7 11/2”l 0 I Grit WAGOK I Part No 741004-0 Eyeshield Part No. 122203-7 / 0 Tool rest (C) Part No.
125 mm (5") BENCH GRINDER Model 9300 Note: The switch and other part configurations may differ from country to cointry.
'LkM $tD E ' M $ED DESCRIPTION MAC E! MnC 1 1 P. H. Screw M4.8 2 1 Side Cover I R I 3 1 H. Nut W l 1 2 - 2 1 4 1 Outer Flange 50 IWifh Washer) IRight-handscrew) 5 1 Inner Flange 50 6 3 P. H. Screw M5r10 IWith Warherl 7 1 Wheel Cover I R I 8 1 stator 9 1 Adlust Plats ( A I 10 2 1 1 P. H. Screw M6x16 (With Washer1 12 13 P," 4.5 DESCRIPTION UE 40 1 CORD ASSEMBLY I A s r m b l e d Cord. Plug & Cord Gusrdl 41 1 42 1 P.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
