A A A B A MODEL 9040L INSTRUCTION MANUAL DOUBLE INSULATION No load speed Overall length (RPMl 6,000 I 470 mm (18-1/2") Net weight I 4.8 kg (10.6 Ibsl Spindle thread I * Manufacturer reserves the right to change specifications without notice. * Note: Specifications may differ from country to country. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
GENERAL SAFETY RULES (For All Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS READ ALL INSTRUCTIONS. 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
11. Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents. 12. Remove adjusting keys or switches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. 13. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. 14.
Specific Safety Rules 1. Always use proper guard with grinding wheel. A guard protects operator from broken wheel fragments. 2.Accessories must be rated for at last the speed recommended on the tool warning label. Wheels and other accessories running over rated speed can fly apart and cause injury. 3.Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord.
SYMBOLS The followings show the symbols used for tool. ................................. volts ............................ ................................. herts ................ .........kilograms ............................. ............................. ..................... seconds ................................. alternating current ... .................... direct current ................................. alternating or direct current .................................
Installing side grip (auxiliary handle) Always install the side grip on the tool securely before operation. The side grip can be installed in any of three positions on the sides of the tool, whichever is convenient and keeps the guard properly positioned. Always hold the tool’s switch handle and the side grip firmly with both hands during operation.
To tighten the lock nut, press the shaft lock firmly so that the spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise. 1 r Lock nut wrench Shaft lock 3 - I To remove the disc, follow the installation procedure in reverse. IF USED AS A GRINDER NOTE: Use grinder accessories specified in this manual. These must be purchased by separate. WARN ING: Always use guard assembly or accessory kit, noted below, for type 2 7 depressed center wheel. Guard assembly Part No.
Installing or removing depressed center wheel CAUTION: Always be sure that the tool is switched off and unplugged before installing or removing the wheel. Mount the inner flange onto the spindle. Fit the wheel on over the inner flange and screw the lock nut onto the spindle. To tighten the lock nut, press the shaft lock firmly so that the spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise.
Operation Hold the tool firmly. Turn the tool on and then apply the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an angle of about 1 5 O to the workpiece surface. During the break-in period with a new wheel, do not work the grinder in the B direction or it will cut into the workpiece. Once the edge of the wheel has been rounded off by use, the wheel may be worked in both A and B directions. WARNING: It should never be necessary t o force the tool.
MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes When the resin insulating tip inside the carbon brush is exposed to contact the commutator, it will automatically shut off the motor. When this occurs, both carbon brushes should be replaced at the same time. Use only identical carbon brushes. 7 Insulating tip dL Carbon brush Use a screwdriver to remove the brush holder caps.
ACCESSORIES CAUTION: These accessories or attachments are recommended for use w i t h your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury t o persons. The accessories or attachments should be used only in the proper and intended manner. @Depressed center wheel (1 Per p k d @Wheel guard Size (mm) Size (mm) 165191-5 180 ( 7 ” ) 164879-4 230 (9”) 180 x 6 x 22 (7” x 114“ x 718”) @Inner flange 89 (For depressed center wheel) Part No.
@Abrasive disc ( 5 per pkg) @Rubber pad Part No. 743012 7 7 1 @Sanding lock nut 48 (For abrasive disc) Part No. 224517-1 Grit Part No. 742067-A-5 16 742069-A-5 24 742089-A-5 Diameter Imm) 180 (7") 742070-A-5 742071-A-5 742091-A-5 @Wire cup brush 120 @Flexible grinding wheel (10 per pkg) I-. I Part No. Diameter (mm) 743206-A Size (mm) 150 16") 743206-8 741442-6 @Urethane washer 14 Part No. 261039-0 180 x 3 x 22 (7" x 118" x 718'7 (includes one back up pad, @ Part No.
May-13--'98 EN ANGLE SANDER Model 9040L Note: The switch, noise suppressor and other part configurations may differ from country to country.
MODEL 9040L %\M AtD 0ct.-08-'96 DESCRIPTION 'LtM GFD NE MACHINE ~ 1 2 4 5 1 1 1 1 1 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 1 1 1 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 3 - - FIELD ASSEMBLY Baffle Plate Ball Bearing 6200DDW lnsdation Washer ARMATURE ASSEMBLY (With item 3. 4 & 61 Fan 80 Bearing Retainer 60 Ball Bearing 6301DDW Spiral Bevel Gear 12 Retaining Ring S-9 Tapping Screw. Flange. 5x35 Pin Cap Compression Spring 12 Hex.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.