DOUBLE INSULATION I N S T R U C T I O N M A N U A L READ and UNDERSTAND before using. TIONS FOR FUTURE REFERENCE. ww. makitatools.
SPECIFICATIONS Net weight Belt size Belt speed Overall length 9 mm x 533 mm (3/8" x 21") 5 - 28 mls 420 mm 1.5 kg (16-1/2") (3.3 Ibs) (980 - 5600 fthin.) Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) A WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.
6. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 7. Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock. 8. When operating a power tool outside, use an outdoor extension cord marked "W-A" or "W".
24. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance instructions may create a risk of electric shock or injury. USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw.
SAVE THESE INSTRUCTIONS A WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. SYMBOLS USD204-3 The followings show the symbols used for tool. v ....................... volts A ....................... amperes mls .................... Hz ..................... hertz Wmin ................feet per minute ...................Class II Construction meter per second CL ................
FUNCTIONAL DESCRIPTION A CAUTION: Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 001215 Adjusting arm inclination The arm can be pivoted and fixed at any desired angle within the "A" range according to the operating position or the figure of the workpiece. Loosen the lock lever by raising it. Pivot the arm to the desired position, and secure the lock lever to fix the arm firmly. 1. Lock lever 2.
001218 I Speed adjusting dial The belt speed can be infinitely adjusted between 5 m and 28 m per second (980 - 5600 ft./min.) by turning the speed adjusting dial to a given number setting from 1 to 6. Higher speed is obtained when the dial is turned in the direction of number 6; lower speed is obtained when it is turned in the direction of number 1. Select the proper speed for the workpiece to be sanded. 1.
001221 Connecting to Makita vacuum cleaner or dust collector A CAUTION: Always close the nozzle cap when the vacuum cleaner/ dust collector is not connected to the nozzle. Never insert your finger into the nozzle. Cleaner sanding operations can be performed by connecting the belt sander to Makita vacuum cleaner or dust collector. 2. Hose28 3. Hose of vacuum cleaner 4. Vacuum cleaner Open the nozzle cap, and install the dust nozzle.
OPERATION W177R Hold the tool firmly with both hands. Turn the tool on and wait until it attains full speed. Gently apply the tool to the workpiece surface and move the tool forward and back. Press the belt only lightly on the workpiece. Excessive pressure may damage the belt and shorten tool life. Always use "A" range of the belt to sand the workpiece. 001224 001225 A CAUTION: Secure the workpiece with clamps, etc. if there is any possibility of it moving during the work operations.
MAINTENANCE A CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. Limit mark 001226 I 1 I I Use a screwdriver to remove the brush holder caps.
These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita service center.
Memo ........ ........ ................... .._ _ . . . - .... __. ..__. . .- 12 . . . , . ...
Firs1 Class not deliver WlthOUl I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I Makita U.S.A., Inc.
MAIL THIS PORTION I I I I I I Your answer to the following questions are appreciated. 0Home Center 0Other ( 0Hardware/Lumber Store ) Tool Distributor Store Display [7 Construction supply 0Catalog 2. Use of the product is intended for: 4.
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ALIBAMA 2365 l'clttam l ' n k w a y f'dhain A 1 35174 1205,120 1791 PUERTO ROC0 200 Goa"" HaloHey PRO3917 (787) 250 8776 s, TENNESSEE 4655 Nuleiinville Rd Nashville TN 37211 16l5)331 9922 3453 114 15 N",li, Sle IO, hnn Anlonia 7 X /8210 (?l"122R(Xi/G l121N L:lovirAue hrru, c* 83127 15501752 5166 Sle 112 GEORGIA 4680 Rive1 Green Parkway NW Uul,ilh GA 3ooM (1701471, "91 I HAWAII 4510 Salt Iahe Elvd iiiile A 7 H'inolu,,, ,I 9
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work.