25 mm ( 5 ” ) MODEL 9005B 125 mm ( 5 ” ) MODEL 9005BZ INSTRUCTION MANUAL DOUBLE INSULATlO N SPECIFICATI0 NS (RPM) AMPS (115 V) Overall length Net weight Power supply cord Spindle thread 10,000lmin. 9 A 356 mm ( 14”) 3 kg (6.6 Ibs) 2.5 m (8.2 ft.) 518-11 UNC No load speed Manufacturer reserves the right t o change specifications without notice. * Specifications may differ from country t o country.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools t o rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure t o use one heavy enough to carry the current your product will draw.
VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY t o the user - as well as damage t o the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating is harmful t o the motor. SAVE THESE INSTRUCTIONS.
Precautions in use Check for cracks in the depressed center wheel and for loose or missing screws. Always use the guard. It can prevent an accident if a wheel should ever break. Before using the disc grinder on an actual workpiece, let it simply run for several minutes first. Watch for flutter that might be caused by poor installation or a poorly balanced wheel. Choose a wheel grade in terms of the workpiece material.
Switch action CAUTION: Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. For Model 9005B To start the tool, simply pull the trigger. Release the trigger to stop. For continuous operation, pull the trigger and then push in the lock button. To stop the tool from the locked position, pull the trigger fully, then release it. Switch trigger Lock button Fig.
OPERATION CAUTION: After use, always switch off and wait for the wheel to come to a complete stop before placing the tool down. Hold the tool firmly. Turn the tool on and then apply the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an angle of about 15" to the workpiece surface. During the break-in period with a new wheel, do not work the grinder in the B direction or it will cut into the workpiece.
MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. Fig. 6 Use a screwdriver to remove the brush holder caps.
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury t o persons. The accessories or attachments should be used only in the proper and intended manner. Abrasive discs 125 mm (5") Wheel cover assembly Part No. 13421 4 0 Part No. Inner flange 82 (For depressed center wheel) Part No.
Jan.-20-'2000 US 125 mm (5") DISC GRINDER Model 9005B Model 9005Bz Note: The switch and other part configurations may differ from country to country.
MODEL 90058.
MAKITA LIMITEDONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted t o be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool. freight prepaid, to one of Makita’s Factory or Authorized Service Centers.