Cordless Ratchet Wrench With 318’’Square Drive Socket Adapter MODEL 6912D MODEL 6912DW With Fast Charger INSTRUCTION MANUAL SPECIFICATIONS 71 Capacities No load speed IRPMI Tightening torque Overall length Net weight Bolt size 12 mm (112’’) I I 400 38 kg Battery Cartridge 7000 Voltage 7.2 V I Charging time 1 Hr. . cm 12.7 f t . Ibsl I I I I 322 mm I12-11/16”1 0.85 kg 11.9 Ibsl Model DC7100 Fast Charger I Input A.C. only 50 Hz - 60 Hz output D.C. 7.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools t o rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger o n switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don’t operate tool when you are tired. 18.
IMPORTANT SAFETY INSTRUCTIONS I. SAVE THESE INSTRUCTIONS - This manual Length of Cord (Feet) AWG Size of Cord 25 18 50 18 100 18 150 16 9. Do not operate charger with damaged cord or plug - replace them immediately. IO. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it t o a qualified serviceman. 1 1 . Do not disassemble charger or battery cartridge; take it t o a qualified serviceman when service or repair is required.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. 3. Do not allow anything t o cover or clog the charger vents. 4. Always cover the battery terminals with the battery cover when the battery cartridge is not used. 5. A battery short can cause a large current flow, overheating, possible burns and even a breakdown.
Installing or removing battery cartridge .Always switch off the tool before insertion or removal of the battery cartridge. .To remove the battery cartridge, pull out the set plate on the tool andgrasp both sides of the cartridge while withdrawing it from the barrel. 0 I I Set plate I I------ I , Battery cartridge I Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly.
Installing socket adapter When you wish t o use a smaller size socket, install the socket adapter. To install it, insert the socket adapter into the socket in the tool, making sure that the tightening direction matches the arrow on the tool. To loosen the nut or bolt, turn the tool o v e r (upside-down) and insert the socket adapter into the socket in the tool. Socket adapter I Switch action To start the tool, simply depress the switch lever. Release the switch lever to stop.
2. Final manual tightening operation After turning the tool off, perform the final manual tightening operation by pulling on the tool grip in the same tightening direction. The maximum size of standard bolts that can be tightened with this tool i s 1/2" (socket size: 13/16'). Refer t o the table for the correct tightening torque and check the torque with a torque wrench. Standard bolt Size Tightening torque Socket size M8 11 5 kg . cm (8.3 ft . Ibs.) 13 mm M10 230 kg . cm (16.6 f t . Ibs.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
ACCESS0 R I ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury t o persons. The accessories or attachments should be used only in the proper and intended manner. e Fast charger Model D C 7 1 0 0 *Charger 1 2 V for car Model DC7112 e Socket adapter 9.5 (Square drive size 3/8") Part No. 785404-4 e Battery cartridge 7000 Part No. 632002-4 Battery cover Part No.
June-26-'86 EN CORDLESS RATCHET WRENCH Model 69120 Note: The s w i t c h and o t h e r part configurations may differ f r o m c o u n t r y t o country.
June- 26-’86 MODEL 6912D /LM ‘i,‘dn A:D $tDDESCRIPTION EN DESCRIPTION ~ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 11 18 19 20 2 1 2 1 2 2 1 1 1 1 1 1 1 1 3 3 1 1 1 1 21 22 23 24 Hex Socket Head Bolt M4x18 Sub Housing R Hex Socket Head Boll M4x25 (With Warherl Name Plate Hex Socker Head Bolt M4x25 (With Warherl Flat Washer 4 Housing R set Plate Switch Lever Compresrlon Spring 6 Motor S p u r G e a r 17 Flat Washer 15 Internal Gear 4 9 S p ~ G e a r16 Pin3 Clutch Cam Splndle Steel Ball 3 5 Flat W