ENGLISH (Original instructions) INSTRUCTION MANUAL Impact Wrench 6904VH 6905H 005299 DOUBLE INSULATION IMPORTANT: Read Before Using.
ENGLISH (Original instructions) SPECIFICATIONS Model 6904VH 6905H M10 - M16 M12 - M20 High tensile bolt M10 - M12 M12 - M16 Wood screw 6 mm x 100 mm - Self-drilling screw 6 mm - 12.7 mm 12.7 mm High: 0 - 2,400 2,200 Standard bolt Capacities Square drive No load speed (min-1) Impacts per minute Max. fastening torque Low: 0 - 2,100 - High: 0 - 3,000 2,600 Low: 0 - 2,500 - High: 196 N.m 294 N.m Low: 147 N.m - Overall length 265 mm 275 mm Net weight 1.8 kg 2.
0.1.2009 Model 6905H Work mode : impact tightening of fasteners of the maximum capacity of the tool Vibration emission (ah) : 6.0 m/s2 Uncertainty (K) : 1.5 m/s2 000230 Tomoyasu Kato Director Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi, 446-8502, JAPAN ENG901-1 • • • • The declared vibration emission value has been measured in accordance with the standard test method and may be used for comparing one tool with another.
accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. 21. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. 22. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation.
For 6904VH This tool has a reversing switch to change the rotational direction. Press the upper side (FWD side) for clockwise (forward) rotation or the lower side (REV side) for counterclockwise (reverse) rotation. For 6905H This tool has a reversing switch to change the rotational direction. Press the right side of the switch for clockwise (forward) rotation or the left side for counterclockwise (reverse) rotation.
OPERATION ASSEMBLY CAUTION: Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Selecting correct socket Standard bolt Always use the correct size socket for bolts and nuts. An incorrect size socket will result in inaccurate and inconsistent fastening torque and/or damage to the bolt or nut. M16X50 at high speed 140 (101) 120 (87) Fastening torque Installing or removing socket 1. Socket 2. Anvil 1 For 6904VH N.m (ft.
N.m . (kg cm) Fastening torque M16X50 M20 M16X50 M16 M12X50 1 1.5 1 2 3 4 5 6 8 7 (S) For 6904VH only When driving screws, install a bit adapter (optional accessory) on the tool and insert a driver bit (optional accessory) into the bit adapter. Hold the tool firmly and place the point of the driver bit in the screw head. Apply forward pressure to the tool to the extent that the bit will not slip off the screw. Start the tool slowly and then increase the speed gradually.
MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. • Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result. To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts.
Makita Corporation Anjo, Aichi, Japan 883774E222 12 www.makita.
