MODEL 6720D MODEL 6720DW With Quick Charger INSTRUCTION MANUAL SPEC IFICAT IONS Model 6720D Capdcities Wood screw No load speed IRPMi Dimensions (Length x Didmeter) weiyht 150 2 0 9 mm x 4 2 mm ( 8 1/4" x 1 5/8"1 0 4 ky 10 9 lbsi ~~ 5 rrim 11 3r64"l 4 1 riim x 2 0 mm 15t32" x 3)4"1 A C only 50 H r Charging time 0Utl)"f II1(1Ut 60 H r I DC24V I * Manufacturer reserves the right to change specifications without notice. * Note: Specifications may differ from country to country.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools t o rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don't operate tool when you are tired. 18.
IMPORTANT SAFETY INSTRUCTIONS I. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2)product using battery. 3. CAUTION - To reduce risk o f injury, charge only MAKITA type rechargeable batteries. Other types of batteries may burst causing personal injury and damage. 4. Do not expose charger t o rain or snow. 5.
ADDITIONAL SAFETY RULES FOR CHARGER AND TOOL 1. The Charger and the tool are specifically designed t o work together. Do not attempt t o charge any other cordless tool with this Charger. Do not attempt t o charge the tool with any other charger. 2. Do not charge the tool when temperature i s BELOW 10°C (5OOF) or ABOVE 45OC (113OF). 3. Do not use charger in damp or wet locations. 4. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. 5.
Charging Connect the charging plug t o the charging connector, then plug in the charger to the power receptacle. Charging takes 3 hours. CAUTION : 0The battery in your new tool i s not fully charged. You will need to charge it before use. 0 0 Do not operate the tool during charging. Overcharging more than 2 days considerably shortens the battery service life. Always unplug the charger after completing the charge.
Reversingswitch action This tool has a reversing switch to change the direction of rotation. Move the reversing switch lever to the right for clockwise rotation or to the left for counterclockwise. Reversing switch lever Counterclockwise CAUTION : Always check the direction of rotation before operation. 0 0Use the reversing switch only when the tool comes to a complete stop. Changing the direction of rotation before the tool stops may ruin the tool.
Manual driving operation This tool can be used as a manual screwdriver when the switch is in the off position. Be sure to keep your finger off the switch when performing manual driving operation CAUTION: When performing manual driving operation, do not insert a screwdriver, etc. into the hole in the end of the tool to increase torque on the screw. This may cause tool damage. Dimensions of screw Application Fastenings Workpiece 3.
ACCESSOR I ES CAUTION : These accessories . -... . ~ . or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should b e used only in the proper and intended manner. 0 Bits I Ph 1 1 lips Slotted #+ F 1 Size I 0 Part NO. Quick charger (A.C.
Sep--16-'87 EN CORDLESS SCREWDRIVER Model 6720D Note: The switch and other part configurations may differ from country to country.
MODEL 6 7 2 0 D ITEM NO. NO.
P Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. Ni-Cd To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b). Take the battery to your nearest Makita Authorized Service Center or Distributor that has been designated as a Makita battery recycling location.