Cordless Screwdriver MODEL 6710D MODEL 6710DW With Fast Charger INSTRUCTION MANUAL I SPECIFICATIONS Model 6 7 1 0 0 Wood screws 5 1 mm x 50 mm 11.4' Machine screws Nuts 6 mm 6 mm (1/4") f 114") x 2 ' l Battery Cartridge 7 0 0 0 speed length weight 220 195 mm 17-518") 1 1 kg 12.4 lhsl Rimin Model OC7100 Fast charger Dimensions iL x W x H) 7 2 V 1 Hr A.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp 3. 4. 5. 6. 7. 8. 9. IO. 11. 12. 13. 2 or wet locations. Keep work area well lit. Don't expose power tools t o rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don't operate tool when you are tired. 18.
IMPORTANT SAFETY INSTRUCTIONS I. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2)battery, and (3)product using battery. 3. CAUTION - To reduce risk of injury, charge only MAKITA Battery 7000. Other types of .batteries may burst causing personal injury and damage. 4. Do not expose charger t o rain or snow. 5.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C or ABOVE 4OoC (104OF). (SOOF) 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. 3. Do not allow anything t o cover or clog the charger vents. 4. Always cover the battery terminals with the battery cover when the battery cartridge is not used. 5. A battery short can cause a large current flow, overheating, possible burns and even a breakdown.
Installing or removing battery cartridge 0 Always switch off the tool before insertion or removal of the battery cartridge. To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel. .To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the set plate back into place. Be sure to close the set plate fully before using the tool.
Switch action 0 Set the reversing switch lever just in front of the trigger switch to Forward (FWD) or Reverse (REV). Then pull the trigger to turn the tool ON and release it to turn it OFF. To change the direction of bit rotation, release the trigger, let the tool come to a complete stop, and then slide the switch lever to the opposite side. The trigger switch does not work if the switch lever is in the neutral position.
Fastening torque adjustment The fastening torque may be adjusted by turning the adjustment ring to align the notched line on the ring with a number on the indicator label. However, the clearance between the ring and the cap is 2.5 mm (1/8") maximum after one full turn, and the ring should not be forced beyond this point.
Hole 0The hole on the heel of the tool is a convenient way to carry it by a cord, hook or other means. Drill chuck (Accessory) 0 To install a drill chuck, remove the insert bit by a strong jerk, then a drill chuck can be replaced with the insert bit by a sharp push of the hand. install the drill bit, place it in the chuck as far as it will go. Tighten the chuck collar by hand. Place the chuck key in each of three holes, and tighten clockwise. .
Screwdriving Match your bit to your screw. Phillips bits Select your screws on and thenominal right. diameter with the chart Item I Rominal Diameter ( m m ) ) Bit No. Wood Screw 2.1 - 2.7 13/32''- 118") 3.1 - 4.8 (1/8" - 3/16') No. 2 No.3 1 5.1 (3/16") Slotted bits Select a slotted bit to match the slot on the screw heads. If the bit is too small for the screw slot, the bit and/or screw head may be damaged.
MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance and adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
ACC ESSOR IES CAUTION: These accessories or attachments are recommended for use w i t h y o u r Makita t o o l specified in this manual. The use o f any other accessories o r attachments m i g h t present a risk of i n j u r y to persons. The accessories or attachments should be used o n l y in t h e proper and intended manner. - 0 Charger 12V for cer M o d e l D C 7112 Part No. 113109-0 Bits Size Part No. #3 784215-0A Phillips Slotted 0 Battery cartridge 7 0 0 0 Part No.
Carrying case Steel case , part N ~823087-3 0 Plastic case Part No. 181428-2 Battery holster Holster holds extra battery. Part No.
Aug -09-'84 US CORDLESS SCREWDRIVER Model 67100 Note: The switch and other part configurations may differ from country to country.
Aug - 0 9 4 4 MODEL 67101D E ’M $&, DESCRIPTION MACHINE 1 1 1 1 1 1 1 1 1 1 1 I 1 1 2 1 - - & DESCRIPTION MACHINE ~ 2 3 4 5 6 7 6 3 10 11 12 13 14 15 ‘i\M US Torque Adlust Ring 20 Cap 0 Ring 16 Guide Plate Lock Washer 14 F Washer 1 4 Leal sprang Sled Ball 3 5 Spindle P,n 4 Compression Spring 14 T Washer 1 0 Clutch Cam Steel Ball 6 4 Spur Gear 86 16 17 18 19 20 21 22 23 24 25 1 1 I 1 1 1 1 2 1 F Washer 8 Ball Bearing 60BLLB Retaining Ring S - 6 Housing Set 1WNh Item Battery 7000 361 Sw
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.