Cordless Driver Equipped 9.6 V 12V 14.
SPECIfiCATIONS Capacities No load speed (RPM) Model Steel Wood Wood screw Machine so'ew Overafl Net Low length weight lOmm 2tram 5.1 minx 6Z260 (3/8") (13/16") (13/_4" x 1-I/2"1 6ram (1/4"} 0-1,100 imP. 0-350 /Ynin. 210 rnrn (8-1/4") 1.4kg (3,1 Ibs) 6227D 1gram {3/8"1 24rnm (15/16") 5.1 rr_m x 63 mm 113/64" x 2-1/2") 5ram (114"} 0-1,100 /r_n. 0-350 /rain. 210 mrn (B-1/4"1 1.5kg 13.3 Ibsl 6228D 10ram (3J8") 24ram (I_16") 5.
GENERAL SAFETY RULES (For All Battery Operated Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury, SAVE THESE INSTRUCTIONS Work Area 1. Keep your work area clean end well lit. Cluttered benches and dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
ToolUseandCare 12.Useclamps or other practical way to secure and support the workplace to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control, 13. Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. 14. Do not use tool if switch does not turn It on or off. A tool that cannot be controlled with the switch is dangerous and must be repaired. 15.
Specific Safety Rules 1. Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden widng. Contact with a "live" wire will also make exposed metal parts of the tool "live" and shock the operator. 2. Be aware that this tool is always in an operating condition, not have to be plugged into an electrical outlet. 3. Always because it does be sure you have s firm footing. 4. Be sure no one is below when using the tool in high locations. 5.
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE 1.SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all Instructions and cautionary markings on (1} battery charger, (2) battery, and (3) product using battery. 3. CAUTION -- To reduce dsk of injury, charge only MAKITA rechargeable batteries marked on the charger label. Other types of batteries may burst causing personal injury and damage.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge or ABOVE 40°C (104°F}. 2. Do not attempt receptacle. when temperature is BELOW lO°C °_®" (50°F) to use • step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals cartridge is not used. with the battery cover when the battery 5. A battery short can cause a large current flow, overheating, and even a breakdown.
FUNCTIONAL DESCRIPTION InstelUng or removing battery aartrldge • Always switch off the tool before insertion or removal of the battery cartridge. =To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge. • To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click.
Tricklecharge(Maintenance charge) tf youleavethebattery cartridge inthecharger toprevent spontaneous discharging after ful_charge, thecharger willswitchintoits"trickle charge (maintenance charge)" mode and keep the battery cartridge fresh and fully charged. Tips for maintaining maximum battery life 1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battew cartridge when you notice less tool power. 2. Never recharge a fully charged battery cartridge.
Speed change To change the speed, first switch off the tool end then slide the speed change lever to the "Ill" side for high speed or "l" side for low speed. Be sure that the speed change lever is set to the correct position before operation. Use the right speed for your job. Low_ Highspeed _-- Speed d_nge lever CAUTION: • Always set the speed change lever fully to the correct position.
ASSEMBLY Installing or removing driver bit or drill bit CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit. Hold the ring and turn the sleeve counterclockwise to open the chuck jaws. Place the bit in the chuck as far as it will go. Hold the ring firmly end turn the sleeve clockwise to tighten the chuck. Tighlen To remove the bit, hold the ring and turn the sleeve counterclockwise.
OPERATION ScrewdrMng operation Place the point of the driver bit in the screw head and apply pressure to the tool, Start the tool slowly and then increase the speed gradually, Release the trigger as soon as the clutch cuts in, NOTE: oMake surethat the driverbit is insertedstraightin the screwheed, or the screw and/or bit may be damaged. *When driving wood screws, preddll pilot holes to make driving easier and to prevent splitting of the work,piece. See the chart.
CAUTION: • Pressing excessively on the tool will not speed up the drilling. In fact. this excessive prossure will only serve to damage the tip of your bit, decrease the tool performance and shorten the service life of the tool. • There is a tremendous force exerted on the toot/bit at the time of hole breakthrough. Hold the tool firmly and exert care when the bit begins to break through the workpiece.
MAINTENANCE CAUTION: Always besurethatthetoolisswitched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY. repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Recycling the Battery The only way to dispose of a Maklta battery to recycle It. The law prohibits any other method of disposal. Is Ni-Cd To recycle the battery: 1.
ACCESSORIES CAUTJON: These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. .Bit= Size PartNo. II 2 784214-0A #3 784215-0A Phillips Slotted # 51: 784010-0A # 7F 784011-0A Squ_redr_ bit • Double-ended Phillips I Slotted bit 1-3/4" long Pert No 784614-0 2-1/2" long Part No.
• Battary charger Model DC9710 Model DC1470 • High rapacity battery charger Model DC1411 • Battery cartridge 9120 / 9122 1 9134 1 9135 • Battery oartrldge • Bat*my cartridge 1220 1 1222 1 1234 1 1235 • Set plato • Plalli* carrying 13 case 1420 1 1422 / 1434 / 1436
D___oe-,99 us CORDLESS DRIVER DRILL Model 6226D Model 6227D Model 6228D Note: The switch and other part confi_urations may differ from country to country.
MOO_L 822_LO*622?0, 622air iTEM NO. NO. USED Oec.--08 I]_ICNPTION I_NO. MACHrN[ I 3 4 MACHIN 1 t t 8 9 8 TaPlOCngS:mw _nd PT 31(16 For Medal 622_D.
MAKITA LIMITEDONE YEARWARRANTY V_n'anty Policy Every MaU_ tool is thorou_ly Imq?m#._land tuted bdO_ _ the fmory. It I=v.zmmted to be free of d_'ec¢0 horn woW,mmship w_d mtOntJ/or tin period of ONE YEAR from the date of pu_. _,]d anyU_L _, chr,_pdudq_ _e-ymr p_, tool fgdsltt pt_pa_l, to o_ of _ J Parody ot Auth_ the trouble _ €_ by deagtive wofhutnddp or mst_id.