Cordless Driver DriII MODEL 6012HD MODEL 6012HDW With Fast Charger and Carrylng Case INSTRUCTION MANUAL S PEClFICAT10NS Model 6012HD Steel Wood Wood screw Machine screw 6 5 mm 1114"l 1 5 mm 5 . 1 mm x 55 mm 13/16" x 2-118") 6 mm 1114") 1518") Battery Cartridge 9 0 0 0 Voltage 9 Nuts I :Em) 1 400 ' lrloo 1 261 mm 110-114") 1 1.6 kg 13.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools t o rain.
13. DISCONNECT TOOLS. When not in use, before servicing, and when changing accessories, such as blades, bits, cutters. 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger o n switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS.
1. SAVE THESE INSTRUCTIONS - This manual 2. 3. 4. 5. 6. 7. 8. Length of Cord (Feet) 25 50 100 150 AWG Size of Cord 18 18 18 16 9. Do not operate charger w i t h damaged cord or plug - replace them immediately. 10. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it t o a qualified serviceman. 11. Do not disassemble charger or battery cartridge; take it t o a qualified serviceman when service or repair is required.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5O0F1 or ABOVE 4OoC (104OF). 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. 3. Do not allow anything t o cover or clog the charger vents. 4. Always cover the battery terminals w i t h the battery cover when the battery cartridge is not used. 5.
Installing or removing battery cartridge 0Always switch off the tool before insertion or removal of the battery cartridge. 0 0 To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel. I Set plate To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the set plate back into place.
When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, it may not accept a full charge. This i s a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it almost completely a couple of times. 0 If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger.
Drill *Punch a small hole in the metal to prevent the bit from skitterring when starting to drill a hole. 0 Use machine oil on the bit to facilitate drill ing. .Pressing down too hard on the tool will not speed up the drilling. In fact, this undue pressure will only serve t o damage the tip of your drill bit, decrease your drilling performance and shorten the service of the tool. 0There is a tremendous force exerted on the tool/bit a t the time of hole break through.
Screw Match vour bit to vour screw. Phillips bits Phillips bit No. 2-65 mm is standard equipped. Select your screws and nominal diameter with the chart on the right. Item I Bit No. I No. 3 I I Nominal diameter (mm) Wood screw I I Machine screw 2.1 - 2.7 M2 - M2.6 3.1 - 4.8 M3 - M5.5 5.1 (13/64") I M6 (1/4") Slotted bits Unless you use a bit that fits properly the slot on the head of the screw, the slot will be damaged and the screw will not fasten.
Speed changeover .To change the speed, turn the speed change knob 180" while the drill is running. Be sure that the speed change knob i s turned to the correct speed setting before you begin operation. See arrow indication. Use the right speed for the job. Fastening torque adjustment Just turn the fastening torque adjust knob on the tool in order to select any of 5 different fastening torques. Make sure that the arrow points to the right torque before you begin the job.
*The hole on the heel of the tool is a convenient way to carry it by a cord, hook or other means.
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Fast charger Model DC9700 0 Makita Battery cartridge 9000 (9.6 V) 1 hour fast charge nickel cadmium battery Part No.
0 Tool holster has some bits storage space. Use holster t o carry drill only after removing bit. Also, keep the reversing switch lever in neutral position when carrying in the holster. Part No. 823033-36 Part No. 823033-3E (Genuine leather) 0 Tool carrying case Part No. 823085-7 (Steel case) Part No.
Feb 19 86 EN CORDLESS DRIVER DRILL Model 6012HD Note: The switch and other part configurations may differ f r o m country to country 14
MODEL 6012HD Feb-19-86 EDDESCRIPTION EN DESCRIPTION ",',;I MACHINE ______ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 1 1 1 I 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Pan Head Screw M5x18 Drill Chuck S 1 0 Spindle Pi" 3 Ball Bearinq 6000LLB STOPRing E 9 Compresslo" Spr,ng 10 Thin Washer 1 0 Spur Gear 7 8 Ring 16 Spur Gear 9 3 Thin Washer 1 0 Compression Spring 1 0 Flat Washer 5 Plane Bearing 5 Shift Knob Supporler compress~o" spr ny 3 S ~ e e Ball l 4 8 Shift Knob Retaining Ri
The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. I Ni-Cd 1 To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b). Take the battery to your nearest Makita Authorized Service Center or Distributor that has been designated as a Makita battery recycling location.