a Uni-Drill 10 mm (3/8") MODEL 6000LR INSTRUCTION MANUAL DOUBLE INSULATION SPECIFICAT IONS CaDacities No load (steel) ~~~~~ Machine & wood screws Self drilling screws Bolts & Nuts, Tapper ~~~~ 1 Overall length * Manufacturer reserves the right t o change specifications w i t h o u t notice. * Note: Specifications may differ from country t o country.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain.
13. DISCONNECT TOOLS. When not in use, before servicing, and when changing accessories, such as blades, bits, cutters. 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS.
ADDITIONAL SAFETY RULES 1. Always be sure you have a firm footing. Be Sure no one is below when using the tool in high locations. 2. Hold the tool firmly. 3. Keep hands away from rotating parts. 4. When drilling into walls, floors or wherever "live" electrical wires may be encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool by the insulated grasping surfaces t o prevent electric shock if you drill into a "live" wire. 5. Do not leave the tool running. Operate the tool only when hand-held. 6.
Selecting action mode 1 For drilling, turn the change ring so that the red dot i s aligned with the DRILL marking on the collar. If the change ring will not come all the way, grasp the chuck and turn the change ring again. Do not move the red dot beyond the DRILL marking. For screwdriving, turn the change ring so that the red dot i s aligned with the SCREW marking on the collar.
Installing or removing drill bit or driver bit CAUTION : Always be sure that the tool i s switched off and unplugged before installing or removing the bit. To install the bit, place it in the chuck as far as it will go. Tighten the chuck by hand. Place the chuck key in each of the three holes and tighten clockwise. Be sure t o tighten all three chuck holes evenly. To remove the bit turn the chuck key counterclockwise in just one hole, then loosen the chuck by hand.
Reversing switch action This tool has a reversing switch to change the direction of rotation. Move the reversing switch lever to the "F" position for clockwise rotation or the "R" position for counterclockwise. R e v e r s i n g switch lever I CAUTION : Always check the direction of rotation before drilling. 0 Use the reversing switch only when the tool comes to a complete stop. Changing the direction of rotation before the tool stop may ruin the tool.
Screwdriving operation Turn the change ring so that the red dot is aligned with the SCREW marking. Place the point of the driver bit in the screw head and apply pressure t o the tool. When driving screws, start the tool slowly and then increase the speed gradually. NOTE : When driving small screws, be careful not to damage the screw heads. Ease pressure on the tool as soon as the screws bottom out.
ACCESSORIES CAUTION : These accessories or attachments are recommended for use w i t h your Makita t o o l specified in this manual. The use of any other accessories or attachments might present a risk of injury t o persons. The accessories or attachments should be used only i n the proper and intended manner. 0 Chuck key SI0 Part No. 763412-5 0 G r i p 26 Part No.
Oec.-20-83 10 mm (3/8") UNI-DRILL Model 6000LR Note: The switch, noise suppressor and other part configurations may differ from country to country.
Apr MODEL 6000LR ITEM NO. NO.
1’ MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, retum the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.