Dust Collector INSTRUCTION MANUAL Peak air flow Sealed suction 1.2 m3/min. (42.4 cu.ft./min.) 1,200 m m 147") of water Recoverable capacity 2,2 Hose length Dimensions ( L x W x H) Net weight 1.5 m ( 5 ft.) 240 mm x 140 mm x 340 mm (9-7/16" x 5-1/2" x 13-3/8") 2.9 kg (6.
IMPORTANT SAFETY INSTRUCTIONS WARNING: When using dust collector, safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the followings: READ ALL INSTRUCTIONS BEFORE USING THIS DUST COLLECTOR. 1. PROPER GROUNDING. This tool should be grounded while in use t o protect the operator from electric shock. Connect t o a properly grounded outlet only. See “Grounding Instructions”. 2. GUARD AGAINST ELECTRIC SHOCK.
switch emits sparks when turned ON and OFF, and so does the motor commutator during operation. A dangerous explosion may result. 13. Do not allow t o be used as a toy. Close attention is neccessary when used by or near children. 14. Use only as described in this manual. Use only MAKITA's recommended attachments. 15. Never use the dust collector in the rain. When not in use, store the dust collector indoors. 16. Do not use close t o heat source (stoves, etc.).
GROUNDING INSTRUCTIONS This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current t o reduce the risk of electric shock. This appliance is equipped with a cord having an equipmentgrounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance w i t h all local codes and ordinances.
Attaching shoulder strap and waist belt Attach the shoulder strap to the dust collector using holes in the top and side of the dust collector as shown in the figures below. Always secure the shoulder strap using the buckles. Shoulder ~~ strap Attach the waist belt to the dust collector using holes in the side of the dust collector as shown a t right. Hang the dust collector on your back and adjust the shoulder strap length so that you can carry the dust collector on your back comfortably.
Operation 1 ) When using without your power tool connected : To start the dust collector, press the "ON' side of the switch. Press the "OFF" side of the switch to stop. Switch 2 When using with your power tool connected : T h i s dust collector has an outlet for accepting the plug of your power tool.
Cord hook Use the convenient cord hook as shown a t right to prevent the power tool cord from dangling around your legs. Your legs may get tangled with the dangling cord, causing severe injury to you. Cleaning lever A clogged filter causes poor suction performance and potential damage to the motor. Occasionally use the cleaning lever to clear the dust from the filter. If suction performance becomes poor, move the cleaning lever back and forth about ten times after turning off the dust collector.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Cleaning filter If suction performance will not recover enough even after you use the cleaning lever to clear the dust from the filter and empty out the dust and dirt, proceed as follows to clean the filter. Loosen the four screws which secure the I Hose the filter with clean water to remove any dust from it.
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in t h e proper and intended manner. 0 Hose Nozzle assembly Part No. 122234-6 P a r t No. 150269-7 (1.5 m : 4.9 f t ) Part No. 150327-9 (3 m : 9.8 f t ) 0 Belt assembly Part No. 122416-0 0 Straight pipe Part No.
The following dust extractor attachments, joints and sleeves are available for use with some types of Makita rotary hammers, finishing sander and random orbit sander. Description Applicable model Rotary hammers HR1821, HR2000 HR2511 Dust extractor attachment Part No. 192176-8 B Finishing sander 9036 Random orbit sander BO5000 Rubber sleeve 18-21 Part No.
Nov -20-'91 US DUST COLLECTOR Model 420s Note: The switch and other part configurations may differ from country to country.
/ ; : h i MODEL 4 2NO 05 USEO T Nov-20-'91 DESCRIPTION ITEM NO. NO. USEO 30 31 32 33 34 35 36 1 4 1 1 1 1 1 37 30 39 40 41 1 1 1 1 1 1 1 1 6 1 1 1 1 1 1 1 1 1 1 1 US DESCRIPTION MACHINE ~ i1 i 4 7 8 9 10 11 12 13 14.