Cordless Cutter 85 mm (3-3/8")MODEL 4191DZ 85 mm (3-3/8")MODEL 419lDWA With Battery Cartridge and Fast Charger INSTRUCTION MANUAL S PEClFICAT10NS Model 4191D Blade diameter No load speed Cutting depth 450 (RPM) Overall length weight 0 18 mm ( 0 - 11/16") 1,000 3 1 6 mm (12-1/2") 2.1 kg (4.6 Ibs) 900 0 (0 8 5 mm 13-318") ~ ~ 2 4 mm 15/16") Battery Cartridge 1222 Voltage 12 v ~ Model DC1410 Fast Charger I Input A.C. only 50 - 6 0 Hz I I output D.C. 7.2 V ~ 14.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools t o rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don't operate tool when you are tired. 18. CHECK DAMAGED PARTS.
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE I.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. 3.Do not allow anything t o cover or clog the charger vents. 4. Always cover the battery terminals with the battery cover when the batter.y cartridge is not used. 5. A battery short can cause a large current flow, overheating, possible burns and even a breakdown.
ADDITIONAL SAFETY RULES 1. Be aware that this is always in an operating condition, because it does not have t o be plugged into an electrical outlet. 2. Check the wheel carefully for cracks or damage before operation. Replace cracked or damaged wheel immediately. 3.Use only flanges specified for this tool. 4. Be careful not to damage the spindle, flanges (especially the installing surface) or bolt. Damage t o these parts could result in wheel breakage. 5. Hold the tool firmly. 6.
Installing or removing the battery cartridge 1222 *Always switch off the tool before insertion or removal of the battery cartridge. *To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge. *To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it until it is locked with a little click. *Do not use force when inserting the battery cartridge.
Charging *Your new battery cartridge is not charged. You will need to charge it before use. Use the fast charger Model DC1410 to charge the battery cartridge. *Plug the fast charger into the proper N C Charging light voltage source. The charging light will flash in green color. *Insert the battery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective markings on the fast charger.
Installing or removing diamond wheel CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the wheel. To install the wheel, first loosen the bolt with the hex wrench and remove the bolt and the flange. Then mount the wheel, the flange and the bolt. The wheel should be mounted with the Makita name on the flange side. - Diamond wheel Press the shaft lock so that the wheel cannot revolve.
installing water supply Attach the tank holder on the tank. The tank ,- Tank holder installing portion -Tank Attach the tank holder onto the motor housing. Tighten the screw (B) securely. Connect the cap on the end of the polyvinyl tube to the mouth of the tank. Turn the tank clockwise when making the connection. Then tighten the screw (A) securely to secure the tank.
Hex wrench storage When not in use, the hex wrench can be conveniently stored. Hex wrench 4 b Adjusting the depth of cut Loosen the screw on the depth guide and move the base up or down. You can read the depth of cut by aligning the top of the notch in the depth guide with the graduations on its right side. (Note: This can be done for 0" bevel cutting only.) At the desired depth of cut, secure the base by tightening the screw.
Sighting The front of the base is notched to provide two guide edges. For straight cuts, align the edge with 0" engraved on it with your cutting line on the workpiece. For 45" bevel cuts, align the edge with 45" engraved on it with your cutting line. Switch action To prevent the trigger from being accidentally pulled, a lock-off lever is provided. To start the tool, slide the lock-off lever in the direction of the arrow and pull the trigger. Release the trigger to stop.
Operation Hold the tool firmly. Set the base plate on the workpiece to be cut without the wheel making any contact. Then turn the tool on and wait until the wheel attains full speed. Feed water to the wheel by adjusting the water cock to obtain a gentle flow of water. Move the tool forward over the workpiece surface, keeping it flat and advancing smoothly until the cutting is completed. Keep your cutting line straight and your speed of advance uniform. For fine, clean cuts, cut slowly.
MAINTENANCE CAUTION: Always be sure that the charger is unplugged and the battery cartridge is removed before attempting to perform inspection or maintenance. After use Brush off accumulation of dust on the base To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
OPTIONAL ACCESSORIES The accessories listed in this manual are available at an extra cost from your Makita distributor or Makita factory service center. Service centers are listed on the warranty card packed with your tool. CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons.
Feb -29-'96 US 85 mm (3-3/8") CORDLESS CUTTER Model 4191D Note: The switch and other part configurations may differ from country to country.
MODEL 4191D Feb.
Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. I Ni-Cd I To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b). Take the battery to your nearest Makita Authorized Service Center or Distributor that has been designated as a Makita battery recycling location.