Cutout Tool MODEL 3706 INSTRUCTION MANUAL DOUBLE INSULATION SPECIFICATIONS Collet chuck capacity No load speed (RPM) 1/4", 1/8" 32,0001min. Overall length 250 mm (9-7/8") * Manufacturer reserves the right to change specifications without notice. * Note: Specifications may differ from country to country. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Net weight 1.1 k g ( 2 .
GENERAL SAFETY RULES USAW2-’ (For All Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
11. Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents. 12. Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. 13. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. 14.
Specific Safety Rules USBO49~1 1 . Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its o w n cord. Contact with a ''live" wire will make exposed metal parts of the tool "live" and shock the operator. 2. Wear eye protection and dust mask. 3.Ventilate your work area adequately. 4. Check the bit carefully for cracks or damage before operation. Replace cracked or damaged bit immediately. 5.
SYMBOLS The followings show the symbols used for tool. v .................................... volts A .................................... amperes Hz .................................... herts % .................................... lol alternating current .................................... no load speed .................................... Class II Construction ..Jmin ...................................
To adjust the shoe, turn the thumb screw to loosen. Slide the shoe to the desired position and tighten the thumb screw securely. Check for the proper clearance beneath the workpiece before cutting so that the bit will not strike a hard surface such as the floor, workbench, etc. Shoe Thumb screw Switch action CAUTION: Before plugging in the tool, always check to see that the switch lever actuates properly and returns to the "OFF" position. To start the tool, move the switch lever to the "ON" position.
Note: When using the bit with 1/4" (6.35 mm) shank diameter, first remove the adapter from the collet cone, then install the bit as described above. To remove the bit, follow the installation procedure in reverse. CAUTION: Do not tighten the collet nut without insertinga bit, or the collet cone will break. OPERATION CAUTION: Avoid forcing the bit to bend or twist. It may snap. Before turning the tool on, make sure the bit and collet nut are securely tightened.
When cutting straight line, clamp a straight board firmly to the material and use it as a guide. Move the tool in the direction of the arrow with the shoe base flush with the side of the guide board. When the cut is complete, turn the tool off and wait for the bit to stop rotating and then carefully remove it from the material. Notes: 1. When using the tool, the rotating action causes the tool to pull. The less pressure applied to the tool causes less pull and provides a more accurate cut.
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury t o persons. The accessories or attachments should be used only in the proper and intended manner. - Collet cone Part No. 763608-8 Size : 114" Adapter 3.18 6.35 Part No. 324149-5 Size : 1/8" - 1J4" Drywall guide bit Part No. 733232-1 Size : 114" Drywall guide bit Part No.
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known [to the State of Califomia] to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: Lead from lead-based paints, 9 Crystalline silica from bricks and cement and other masonry products, and 9 Arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work.