ENGLISH (Original instructions) INSTRUCTION MANUAL Router 3620 003251 DOUBLE INSULATION IMPORTANT: Read Before Using.
ENGLISH (Original instructions) SPECIFICATIONS Model 3620 Collet chuck capacity 8 mm or 3/8" Plunge capacity 0 - 35 mm No load speed (min-1) 29,000 Overall height 211 mm Net weight 2.5 kg Safety class /II • Due to our continuing programme of research and development, the specifications herein are subject to change without notice. • Specifications may differ from country to country.
6. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 7. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. 8. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
Power tool use and care 18. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. 19. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. 20.
FUNCTIONAL DESCRIPTION • • CAUTION: Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. • Adjusting the depth of cut 1 1. Stopper pole 2. Screw 2 CAUTION: Since excessive cutting may cause overload of the motor or difficulty in controlling the tool, the depth of cut should not be more than 15 mm at a pass when cutting grooves with an 8 mm diameter bit.
overtightened bit can be dangerous. Do not tighten the collet nut without inserting a bit. It can lead to breakage of the collet cone. Insert the bit all the way into the collet cone and tighten the collet nut securely with the two wrenches. A 6 mm or 1/4" collet cone is also provided as standard equipment besides the 8 mm or 3/8" collet cone that is factory installed on the tool. Use the correct size collet cone for the bit which you intend to use.
2 3 1 Templet guide (Accessory) 1. Feed direction 2. Bit revolving direction 3. Workpiece 4. Straight guide 4 001985 Straight guide 003262 The templet guide provides a sleeve through which the bit passes, allowing use of the tool with templet patterns. To install the templet guide, loosen the screws on the tool base, insert the templet guide and then tighten the screws. 1 1. Screw 2. Base plate 3.
Vacuum head set (Accessory) ACCESSORIES 1. Vacuum head CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
"U"Grooving bit Drill point flush trimming bit R 005120 005117 mm mm D A L1 L2 R D A 6 6 50 18 3 L1 L2 L3 12 12 60 20 35 006453 8 8 60 20 35 "V"Grooving bit 6 6 60 18 28 006456 Drill point double flush trimming bit 005118 mm D A L1 L2 1/4" 20 50 15 005121 D A L1 L2 L3 mm L4 6 6 70 40 12 14 90 006454 Dovetail bit 006457 Slotting cutter 005119 mm D 15S 8 15SE 15L 3/8" 8 15LE 12 3/8" 8 12E 3/8" A L1 L2 14.5 55 10 35 14.
Board-jointing bit Chamfering bit 005123 005127 30 30E D A1 A2 L1 L2 L3 mm C 12 1/2" 30 20 55 12 20 4 006461 005124 mm D A1 A2 L1 L2 L3 12 38 27 61 4 20 006459 005126 Corner rounding bit mm D A L1 L2 L3 6 23 6 20 46 11 6 30 50 13 5 6 20 45 49 14 2 60 006462 Beading bit 005125 D A1 A2 6 25 9 6 20 8 L1 mm R L2 L3 48 13 5 8 45 10 4 4 006460 005128 4R 4RE 006463 10 D A1 A2 L1 L2 L3 mm R 12 1/2" 30 20 55 12 20 4
Ball bearing chamfering bit Cove beading bit 005132 005129 mm mm D A L1 L2 R 6 20 6 25 43 8 4 48 13 8 D 6 1/4" A1 A2 26 6 20 006464 L1 L2 8 42 12 45 8 41 11 60 006467 Ball bearing flush trimming bit Ball bearing beading bit 005130 005133 mm D A L1 L2 6 1/4" 10 50 20 006465 mm R D A1 A2 A3 L1 L2 L3 6 20 12 8 40 10 5.5 4 6 26 12 8 42 12 4.
Ball bearing roman ogee bit 005135 D A1 6 6 L2 L3 R1 mm R2 40 10 4.5 2.5 4.5 42 12 4.5 3 6 A2 L1 20 8 26 8 006470 Double ball bearing round corner bit 005136 3R 3RE D A1 A2 A3 L1 L2 L3 mm R 12 1/2" 35 27 19 70 11 3.
Makita Corporation Anjo, Aichi, Japan 883585F225 16 www.makita.