ENGLISH (Original instructions) INSTRUCTION MANUAL Router 3601B 005038 DOUBLE INSULATION WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ENGLISH SPECIFICATIONS Model 3601B Collet chuck capacity 12 mm or 1/2" No load speed (min-1) 23,000 Overall height 190 mm Net weight 3.6 kg Safety class /II • Due to our continuing programme of research and development, the specifications herein are subject to change without notice. • Specifications may differ from country to country. • Weight according to EPTA-Procedure 01/2003 END201-5 Save all warnings and instructions for future reference.
21. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. 22. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. 23.
10. 11. 12. 13. 14. 15. 16. 17. 18. Before using the tool on an actual workpiece, let it run for a while. Watch for vibration or wobbling that could indicate improperly installed bit. Be careful of the bit rotating direction and the feed direction. Do not leave the tool running. Operate the tool only when hand-held. Always switch off and wait for the bit to come to a complete stop before removing the tool from workpiece.
OPERATION For tool with lock-off button To prevent the switch trigger from being accidentally pulled, a lock-off button is provided. To start the tool, depress the lock-off button and pull the switch trigger. Release the switch trigger to stop. 1 Set the tool base on the workpiece to be cut without the bit making any contact. Then turn the tool on and wait until the bit attains full speed.
Straight guide 1. Base plate 2. Templet guide 2 1 005046 005043 Secure the templet to the workpiece. Place the tool on the templet and move the tool with the templet guide sliding along the side of the templet. The straight guide is effectively used for straight cuts when chamfering or grooving. To install the straight guide, insert the guide bar into the holes in the tool base until the notch in the guide bar reaches just under the wing bolt (B). Then tighten wing bolt (B).
tighten the wing bolt (C) securely. 1. Wing bolt (B) 2. Fine adjusting screw 3. Wing bolt (A) 4. Trimmer guide 5. Wing bolt (C) 6. Guide roller 1 2 3 4 6 5 1 2 3 5 4 1. Hose 2. Joint 3. Vacuum hose 4. Outer diameter φ32 mm 5. Inner diameter φ38 mm 006288 005048 Connect another and of the hose to the vacuum cleaner hose of 38 mm in inner diameter using a joint. When cutting, move the tool with the guide roller riding the side of the workpiece. MAINTENANCE 1. Bit 2. Guide roller 3.
Router bits Then install the rear cover with the screws. 1 Straight bit 1. Brush holder cap 2. Screwdriver 2 005050 005116 CAUTION: • Do not turn the tool on without the rear cover installed in place. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts.
"V"Grooving bit Board-jointing bit 005118 005123 mm D A L1 L2 1/4" 20 50 15 mm 90 D A1 A2 L1 L2 L3 12 38 27 61 4 20 006454 006459 Drill point flush trimming bit Corner rounding bit 005120 005125 mm D A L1 L2 L3 12 12 60 20 35 8 8 60 20 35 6 6 60 18 28 D A1 A2 6 25 9 6 20 8 L1 mm R L2 L3 48 13 5 8 45 10 4 4 006460 006456 Chamfering bit Drill point double flush trimming bit 005126 005121 mm D A L1 L2 L3 mm L4 6 6 70 40 12
Cove beading bit Ball bearing chamfering bit 005129 005132 mm mm D A L1 L2 R 6 20 6 25 43 8 4 48 13 8 D 6 1/4" A1 A2 L1 L2 26 8 42 12 45 6 20 8 41 11 60 006464 006467 Ball bearing flush trimming bit Ball bearing beading bit 005130 005133 mm D A L1 L2 6 1/4" 10 50 20 006465 mm R D A1 A2 A3 L1 L2 L3 6 20 12 8 40 10 5.5 4 6 26 12 8 42 12 4.
Ball bearing roman ogee bit 005135 D A1 6 6 L2 L3 R1 mm R2 40 10 4.5 2.5 4.5 42 12 4.
Makita Corporation 883011I8 12