32mm (5%")MODEL 2004 INSTRUCTION MANUAL MODEL NO. width Auto feed 2004 ~ Manual infeed No, of knives Two on each feed '''0° czkg depth 132" 3mm f5-1/4") f118") Continuour rating, Input - Output 697 Feed ratelmin. Table size fW x L ) Fence size 9.7m 131'8ft') 120" x 410" (4.3/4")~(15.3/4") - Rabbet depth 6mm 1114"l l2Omm x 8OOmm 1 4 4 4 " ) x 131-1/2"1 500" x 70" 119-5/8") x (2-3/4") No load Overall dimensions speed fWx L x HI 8.500 R/min. x 592" 800mm x 423" 131.
BEFORE CONNECTING YOUR TOOL TO A POWER SOURCE Be sure you have read all GENERAL POWER TOOL SAFETY RULES GENERAL SAFETY PRECAUTIONS 1. KEEP GUARDS IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 4. AVOID DANGEROUS ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. 5.
PRE LlMlNAR Y I NSTR UCTlONS Your electric tool i s precision built and manufactured to satisfy the highest standards. For maximum performance, long tool life, and your safety, follow these instructions carefully. VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle, outlet, etc.) be sure the voltage supplied i s the same as that specified on the nameplate of the tool.
Planer -Jointer & Standa rd Equipment Crank handle I Belt cover safety guard - - - - - l I 0Socket wrench 0 Sharpening holder 0 @ Leveller I
Special Precautions with Planer- Jointer a. Jointing Operations Do not perform jointing operations on material shorter than 4-3/8 inches (110mm), narrower than 314 inch (19 mm), or less than 1/4 inch (6.4 mm) thick. b. Planing Operations Do not perform planing operations on material shorter than 4-3/8 inches (110 mm), narrower than 3/4 inch (19 mm), wider than 5-1/4 inches (132 mm) in auto feed and 5-1/4 inches (132 mm) in manual infeed or thinner than 1/2 inch (12.7 mm). c.
3. Return Cut stock can be easily returned by means of the rollers on top. 4. Support long stock a t the beginning and end of a cut to prevent gouging or rough end surfaces. 1. The depth of cut i s indicated in mm on the scale. Turn the knob to the right to increase cutting depth and to the left to decrease it. Maximum cutting depth: 3 mm (1/8"). 2.
I Cutter Replacement I First, unplug the planer-jointer from the power source. 1. Removal Auto infeed table (Planer): First, left off the chip cover (guard). 0 Manual feed table (Jointer): Remove cover (guard) after taking off safety cover (guard) bolt.
2. Installation 0 Hold the belt steady by hand and insert the cutter between the leaf spring and the drum so that the blade protrudes slightly above the table surface. 3. Cutter Height Adjustment Make the drum stationary before performing the adjustment by pressing in the drum locking lever so that it i s released from the stopper; then fasten the drum in place by inserting the end of the lever into the drum concave (grooved) portion.
After hooking the lever for drum locking onto the stopper, secure the hex bolts holding down the blade holder: a total of 8 on the planer arid jointer sides, respectively. 0 After all bolts have been secured, check your cutter height agian. MAINTENANCE 0 Remove the chain guard and lubricate the chain with machine oil. Oil the sliding support parts, moving parts and feed screw portions whenever you think it necessary.
To replace carbon brushes, use the (-1 minus screwdriver equipped to remove the holder cap on the motor housing. Then replace the brush. 0 HOW T O USE T H E SHARPENING HOLDER First, loosen the 2 wing nuts on the holder and insert blades Aand B as in figure a t right, so that they contact side C and D. Then tighten wing nuts. 0 0 Immerse dressing stone in water .Jr 2 or 3 minutes before sharpening.
ACCESSORIES t CAUTION: The used of any other accessories not specified in this manual might be ha ardous. 0 Replacement blades 136 15-3/8"1 Pait No. 731013-7 136 (5-3/8'1 731203-2 Width (mm) * Material . . . Tungsten-Carbide Dressingstone Part No. 741801-4 Part 0 No. 155334-7 Sharpening holder Part No. 123006.2 Socket wrench Part No.
132mm(5%") PLANER JOINTER Model 2004 c 2
$M , PART NO. M A * $Fo 'LkM DEYRlPTlON MA< - PART NO. NE - DESCRIPTION 1 154260-7 1 Ru1I.r 1 Column Supporter 164510-2 1 Chip Cover 58 59 3114484 2 921571-3 4 H. Boll M10x50 IWilh Washer1 3 231098-8 1 Compression Spring 6 60 2531340 4 F.Wmher 11 4 924206-5 T Screw M5x10 61 321132.3 I Screw MZO 62 2544001.2 1 Woadrvll Key 4 SfOP!m 63 221317.0 1 Straqht Bsvsl Gear 16 T Washer 12 64 2533114 1 T. Washer 10 Rullor 26 65 9112268 3 P. H.
M k ;' PART NO. "!& DESCRIPTION MACHINE 11s v. zm v. 220 v. i13342-8 230 V. M; : 1 - 1mv. PART NO. $to DESCRIPTION M" 1 131 687620.7 687609-1 - 250 V 114 141025.7 1 Fan 92 115 L13051-6 1 O"llSs.l 911216-1 10 I32 133 134 2 For Csosda p n &raw M5r14 (With Washer) 253748-5 I 221661-5 1 F WeshCr 12 Helicd Gear 76 3211344 1 S~liodle 116 111066-7 1 Ball Bearing 8200LLB 135 117 ~31270-2 1 CDmDr&On SWlnl 11 136 253797.
&24?c&k-*ud. Anjo, Aichi, h p 8 n c 1 PRINTED IN JAPAN 1979-9-1.