Curved Planer 1I O mm (4-3/8") MODEL 1002BA INSTRUCTION MANUAL Planing width Planing depth No load speed (RPM) Overall length Net weight 110 mm (4-3/8") 4 mm (5/32") 15,000 339 mm (13-1/32") 5 4 kg (1 1 9 Ibs)
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools i n damp or wet locations. Keep work area well lit. Don't expose power tools t o rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONALSTARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure t o use one heavy enough t o carry the current your product will draw.
VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURYt o the user-as well as damage t o the tool. If in doubt, DO NOT PLUG INTHE TOOL. Using a power source with voltage less than the nameplate rating is harmful t o the motor. ADDITIONAL SAFETY RULES 1.
Removing or installing planer blades CAUTION: Always be sure that the tool is switched off and unplugged before removing or installing the blade. To remove the blades on the drum, unscrew the four installation bolts with the socket wrench. The drum cover comes off together with the blades. \ To install the blades, first clean out all chips or foreign matter adhering to the drum or blades.
Adjusting depth of cut Depth of cut may be adjusted by simply turning the knob on the front of the tool. Knob 1 Adjusting front base The front base is factory-adjusted to allow concave cuts with a radius of 320 mm. For concave cuts with the tool’s minimum radius of 300 mm, loosen the wing bolt on either side and raise the front base as far as it will go. Then retighten the two wing bolts firmly to secure the front base. Wing bolt Switch action To start the tool, simply pull the trigger.
Sharpening planer blades Always keep your blades sharp for the best performance possible. Use the sharpening holder to remove nicks and produce a fine edge. First, loosen the two wing nuts on the holder and insert the blades (A) and (B), so that they contact the sides (C) and (D). Then tighten the wing nuts. Sharpening holder Wing nut Side (C) Blade (A) Blade (6) Immerse the dressing stone in water for 2 or 3 minutes before sharpening.
MAINTENANCE CAUTl ON : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. I Limit mark Use a screwdriver to remove the chip cover.
ACCESSORIES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons The accessories or attachments should be used only in the proper and intended manner Planer blade Width 110 mm (4-3/8”) Part No 793008-8 Planer blade (Material Tungsten-carbide) Width 110 m m (4-3/8”) Part No 7930096 Sharpening holder assembly Part No. 123055-9 Socket wrench Part No.
Seo.-ll-'97 US 110 mm (4-318") CURVED PLANER Model 1002BA e Note: The switch and other part configurations may differ from country to country.
MODEL 1002BA ,&, Sep.
i MAKITA LIMITEDONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.