Installation Guide

ManualsBrandsMail Boss ManualsKey CabinetsKey Boss 105 Key Cabinet Combo Locking Drop Box

Have a question?... Need a part ASAP?...1-800-589-7990

We strongly recommend that you WRITE DOWN YOUR COMBINATION / KEY NUMBER and

keep it in a safe place other than inside your Key Boss. Without a key number we will not be able to

provide replacement keys, you will have to purchase a new lock and keys set. For security purposes,

we reserve the right to deny key replacement without proof of purchase. Activate your free Mail Boss

lifetime warranty and register your key number at: www.Mailboss.com/Register

The Wall Mount Bin Style Locking Key Drop box is designed for your security and convenience.

This drop box is constructed of heavy duty galvanized steel and is designed to be installed on a

vertical wall.

Below you will find a list of hardware parts and detailed installation instructions. Please take

the time to carefully sort the hardware and familiarize yourself with the function of each piece for ease

of installation. Typical installation hardware has also been provided for your convenience.

Since concrete is a hard surface, take proper care when installing this hardware into hard surfaces,

making sure not to break the drill bit or screws provided. An electric drill may be required for hard

surface installation.

If you require assistance with assembly, part replacement, or any other matter, contact the

toll-free Epoch Design Service Center from anywhere in the Continental United States,

Monday through Friday, 9 AM - 5 PM Pacific Standard Time at 1-800-589-7990. You may also

email your request or comments to info@mailboss.com and a service representative will respond.

You will also find helpful hints and tips on our website: www.mailboss.com.

Key Boss

Thank you.

1/6

Parts and Hardware List

Attachment Rivets

Used to connect rails

and shelf

Mounting Screws

Connect key box to any wall

Key Boss Drop Box

Locking security key storage

Key Drop Bin

To collect deposited keys

TORX (T25) Drive Bit

Used to drive screws

Long Key Rail

Mounted to the back

wall of the box

Security Keys

Used to lock and unlock

your key box

4 mm Drill Bit

For drilling holes into

concrete, brick,

mortar or wood

Rubber Grommets

Isolates key box from wall

Steel Washers

Used with mounting screws

20-Dec-2019

LOCKING SECURITY MAILBOXES

MAIL BOSS

Key Hooks

For Key Storage

Short Key Rail (front)

Mounted to the door

! IMPORTANT !

Wall anchors

Used when installing

into drywall

Summary of content (8 pages)

PAGE 1
/6 MAIL BOSS ® LOCKING SECURITY MAILBOXES Key Boss ® 20-Dec-2019 The Wall Mount Bin Style Locking Key Drop box is designed for your security and convenience. This drop box is constructed of heavy duty galvanized steel and is designed to be installed on a vertical wall. Below you will find a list of hardware parts and detailed installation instructions. Please take the time to carefully sort the hardware and familiarize yourself with the function of each piece for ease of installation.
PAGE 2
/6 20-Dec-2019 1 1 1 Use a Phillips Head screwdriver to remove the handle from the inside of the bin door then re-attach the handle to the outside of the bin door. Carefully place the box on the wall at about 130 cm to 165 cm above the floor, or according to your preference. Make sure the box is completely level, then mark the center of all four mounting holes. 3 40 mm 3 130 cm to 165 cm 2 2 LEVEL 6.5” (165.
PAGE 3
/6 20-Dec-2019 Handle Upper Bin Door Attachment Rivet Front Access Door Rear Key Rail Key Drop Bin Rear Rail Uprights Attachment Rivet Anti-Pry Bar Lock and Cam Key Tag Key Snap Ring Front Key Rail Mounting Holes Front Rail Uprights 5 If using the Key Boss as a deposit box, install the Key Drop Bin to the top holes of the door’s Front Rail Uprights. Secure by inserting two Attachment Rivets through the holes on the Key Drop Bin and into the door’s Front Rail Uprights.
PAGE 4
/6 20-Dec-2019 7 We realize keys can vary in size and shape dramatically, so where you place the next Key Rail will depend on your individual needs. We recommend attaching a key you will be storing within the Key Boss to the snap ring on a Key Tag, and hang it on the Front Key Rail (installed in step 5) where it works best for your needs. Then install the next Front Key Rail below the keys so the Front Key Rail does not make contact with the keys. Secure with two Attachment Rivets.
PAGE 5
/6 20-Dec-2019 10 You can now attach your keys to the Key Tags and arrange them according to your needs inside the secure locking compartment. OPTIONAL COMBINATION LOCK If your Key Boss came with the optional combination lock, refer below for instructions on how to use: Hooked Cam Set Your Own Combination: The combination can be changed in seconds without special tools or disassembly.
PAGE 6
/6 MAIL BOSS ® 20-Dec-2019 Accessory items and parts available: www.mailboss.
PAGE 7
MAIL BOSS LOCKING SECURITY MAILBOXES ϭ Ϯ ϯ ϰ ϱ ϲ ϳ ϴ ϵ ϭϬ ϭϭ ϭϮ ϭϯ ϭϰ ϭϱ ϭϲ ϭϳ ϭϴ ϭϵ ϮϬ Ϯϭ ϮϮ Ϯϯ Ϯϰ Ϯϱ ® Key Boss ® Ϯϲ Ϯϳ Ϯϴ Ϯϵ ϯϬ ϯϭ ϯϮ ϯϯ ϯϰ ϯϱ ϯϲ ϯϳ ϯϴ ϯϵ ϰϬ ϰϭ ϰϮ ϰϯ ϰϰ ϰϱ ϰϲ ϰϳ ϰϴ ϰϵ ϱϬ Have a question?... Need a part ASAP?...
PAGE 8
MAIL BOSS LOCKING SECURITY MAILBOXES ϱϭ ϱϮ ϱϯ ϱϰ ϱϱ ϱϲ ϱϳ ϱϴ ϱϵ ϲϬ ϲϭ ϲϮ ϲϯ ϲϰ ϲϱ ϲϲ ϲϳ ϲϴ ϲϵ ϳϬ ϳϭ ϳϮ ϳϯ ϳϰ ϳϱ ® Key Boss ® ϳϲ ϳϳ ϳϴ ϳϵ ϴϬ ϴϭ ϴϮ ϴϯ ϴϰ ϴϱ ϴϲ ϴϳ ϴϴ ϴϵ ϵϬ ϵϭ ϵϮ ϵϯ ϵϰ ϵϱ ϵϲ ϵϳ ϵϴ ϵϵ ϭϬϬ Have a question?... Need a part ASAP?...