Models: 30 / 40 / 50 / 50v / 64 / 64v / 80 Please read the instructions carefully before installation and keep for future reference. Please Note: This product is for a well-insulated dwelling.
Table of Contents 1 Important Electrical safety 2 Technical Specifications / Appliance Dimensions 3 Components 4 Operating Instructions 5 Maintenance 6 Warranty
1 Important Electrical safety Read all instructions fully before using this electric fire. This electric fire is for INDOOR USE ONLY. If installing the appliance into an existing Chimney the chimney MUST be blocked off / capped. Do not locate the fire below or in front of a fixed socket outlet. Warning DO NOT COVER the fan heater air inlet / outlet as it could cause possible fire. Note the warning symbol on the fire. Do not use the fire near a bath / shower / swimming pool.
Do not use the appliance in small areas where there are persons are incapable of leaving the area on their own, unless there is constant supervision. This appliance is supplied with a 3 pin moulded plug that is for use of 120V AC 60 Hz. Do NOT operate the appliance if it is damaged.
Appliance Dimensions Model Iconic 30 Iconic 40 Iconic 50 Iconic 50v Iconic 64 Iconic 64v Iconic 80 A 29 ½” 39 3/8” 49 ¼” 49 ¼” 63 63 78 ¾” B 30 ¾” 40 5/8” 50 ½” 50 ½” 64 ¼” 64 ¼” 80 C D E F 23 3/8” 15 13/16” 15 13/16” 15 13/16” 15 13/16” 15 13/16” 15 13/16” 31 5/8” 24 1/16” 24 1/16” 24 1/16” 24 1/16” 24 1/16” 24 1/16” 7 3/8” 7 3/8” 7 3/8” 3 3/4” 7 3/8” 3 3/4” 7 3/8” 11 7/8” 11 7/8” 11 7/8” 8 ¼” 11 7/8” 8 ¼” 11 7/8” Appliance Frame Dimensions Model A B C D Iconic 40 Iconic 50 Iconic 64 Icon
3 Components Before unpacking the fire inspect the carton for any damage, either caused by transport / water etc. If in doubt contact your local retailer, and do not use the appliance. IMPORTANT Keep any plastic packaging and small parts away from young children as they will pose a danger.
4 Operating Instructions Pairing the remote to the appliance To pair the remote to the appliance, first turn on the main switch to put the fire in the standby mode. Press and hold the 2 buttons indicated for 5 seconds, then release and press the button on the remote to complete the pairing process. To ensure the pairing process has been successful simply press the button on the remote to turn the appliance on and off. If the appliance does not turn on / off repeat the process.
Down Light Button Pressing the down light button changes the colours. There are four different colour settings. There are four different modes in the down lighter setting, o o o o Pulse mode Colour change mode pulsing (ideally for a showroom setting) Colour change mode Solid state To activate each mode simply press the down light button and hold for 3 seconds, and this indicates the mode change. Fuel Bed Button Pressing the fuel bed button changes the colours. There are fourteen different colour settings.
Please Note Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
the user manual and must also either be placed on the device packaging or on a removable label attached to the device. However, Trade Name, and Model Number must still be displayed on the device. FCC ID information (if a FCC certified RF module is inserted in) If a certified module is installed inside the host device, then the outside of the host must be labeled with “Contains FCC ID: 2A8S3-RV1”. User manual requirements (SDOC): The following information is shown in the user’s manual.
Label and User manual Requirements for ICES: Labeling requirements (SDoC): The product shall bear the below information in the marking on the device: 1. Name of the manufacturer or trademark: ICONIC Model number: RV1 Rating: DC 4.5V Series number: 2. Compliance Label ISED ICES-003 Class B device Compliance Label: CAN ICES-003(B)/NMB-003(B); Note: This label shall be permanently affixed to the device or displayed electronically and its text must be clearly legible.
This is a thermostatic remote control. The remote control should always be in the same room as the electric fire with the screen facing up. Please do not cover the temperature sensor. Do not leave the remote control next to the fire or a warm area such as a window, this will relay false information to the fire and prevent the fire from turning on and off the heat.
Press SET to save any adjustment or stop operating the remote for 3 seconds and it will automatically save the desired setting selected. 5. Flame effect Press button and the icon will flash on the remote. The flame adjustment is now active. Press the no flame. Press and and to adjust the flame brightness. There are 5 settings, full to button to adjust the colours from number 1 to 4 and then press or stop operating the remote for 3 seconds and it will automatically save the desired setting selected. 6.
The timer settings can be set in the following sequence: CLOCK / DAY TIMER SCHEDULE ① TIMER SCHEDULE ② COUNT DOWN TIMER (1).The first screen that appears is the CLOCK setting screen: Press the SET button, SET on the screen and the Hours will blink, Press UP or DOWN button to scroll the hour settings. Press the SET button, the Minutes will blink, Press UP or DOWN button to scroll the minute settings.
Press the SET button, the DAYS will blink, Press UP or DOWN button to scroll the DAY settings, from M (Monday) to S (Sunday).
(3) The third screen that appears is the Weekly timer schedule ② The setting procedure same as schedule ①.
Press the clock button when home screen, ① icon displayed on the screen, the weekly schedule ① will be enabled, press again clock button, ② icon displayed on the screen, the weekly schedule ② will be enabled. Press again clock button the icon on displayed on the screen, the countdown timer is enabled.
(5) Select the temperature setting range. The factory setting temperature range is 5℃to 35℃,you can reset the temperature range to your preference. 9 Background Volume Press button to adjust background volume. The three volume settings are to to and mute 10 Resetting the Remote control If the remote control does not operate correctly, please take out the batteries to reset the remote to factory the setting. Open the back cover and remove the batteries.
5 Maintenance Always isolate the power from the mains and ensure the fire has cooled down before any cleaning or maintenance is undertaken. Cleaning the appliance Carefully clean the air inlet and heater area with a cloth or vacuum on a regular basis. It is important that these areas are kept free from dust / pet hairs etc. Do not use abrasive cleaners on the appliance. Do not spray liquids directly onto the appliance.
6 IMPORTANT INSTRUCTIONS When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Read all instructions before installing or using this heater. 2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, etc.
18. This appliance must be securely fixed / recessed to an internal wall in the property. Keep all furniture / curtains etc as least 1 meter away from the fire. 19. The fire must be earthed. 20. After the fire’s installation the plug must be accessible. 21. Always disconnect the power supply before any cleaning / maintenance of the appliance. 22. Ensure the appliance is cool before proceeding. 23.
7 Warranty Your Iconic electric fire comes with a two-year parts and labour warranty as standard. The warranty starts from the date of purchase, if you wish to extend the warranty for an extra 12 months you must register the appliance on www.iconicfires.com . To avail of your warranty, you must upload proof of purchase (Receipt) from your local approved Iconic retailer. The warranty is not transferable.