The product as repuired by IEC 60825-1 second edition 2007-03. Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No .50, dated Jane 24,2007 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Welcome Congratulations on purchasing this Flat CD Micro System. You can now listen to your CD's, Bluetooth and FM radio.
Your Flat CD Micro System CD Door Open/Close Stop Function Remote sensor Volume Power / Standby Tuning AUX–IN socket Headphone socket Left speaker socket Right speaker socket DC 5V Power socket Play/Pause LCD Display
Hanging points Back–up batteries (included) Stand Hanging points Speaker cables Speaker Stand FM Antenna
Preparing the remote control IMPORTANT:The remote control will work within a 6m range; however, this may be impossible if there are obstacles between the unit and the control. If the remote control is used near other devices which generate infrared rays then it may not operate properly and may interfere with other devices. For first time use: The unit has a pre-installed lithium CR2025 battery(included)Remove the protective tab to activate the remote control battery.
radio stations in FM condition radio stations in FM condition
Fitting the back-up batteries(included) Backup batteries prevent your CD Micro System from losing all the saved information in the event of a power cut. It is recommended that you fit the batteries. Push the catch on the battery compartment cover in the direction of the arrow shown. You will now be able to lift the cover off. Slot the two AA type batteries into the battery compartment following the directions in the battery compartment.
Setting up your Flat CD Micro System Connecting the power Warning: Ensure your power supply voltage corresponds to the voltage printed on the underside of the unit. 1. Slot the jack on the power adaptor into the power socketin the side of your Flat CD Micro System. 2. Slot the plug on the power adaptor into a wall socket. 3. Switch on at the plug, the unit is now in the standby mode. Setting up the FM aerial Unwind the coiled FM aerial at the back of your Flat CD Micro System.
Positioning your Flat CD Micro System Separated speakers Attached speakers Wall mounted Separated speakers: Using this method the speakers can be separated and placed where you want them. You have already completed all assembly require see below to for how to use the stands. Attached speakers: You can attached the speakers to the sides of the Flat CD Micro System, see page 12. Wall mounted: You can wall mount your Flat CD Micro System with either the speakers attached or unattached.
Attaching the speakers Place a small screwdriver against the bottom edge of the attachment tabs in the sides of the speakers, push them upwards and outwards until fully extended Slot the attachment tabs on the sides of the speakers into the slots in the sides of the Flat CD Micro System. Push the speakers down until the speakers lock on to the sides of the Flat CD Micro System. If you want to detach the speakers, simply push them upwards off the Flat CD Micro System.
Wall mounting WARNING: Before attempting to fit the Flat CD Micro System to the wall, if you are in any way unsure about how or where to fit the Flat CD Micro System you should employ a qualified person to install the Flat CD Micro System. IMPORTANT: There are no fittings supplied with your Flat CD Micro System. Please ensure that any fittings are correct for the wall you will be hanging your Flat CD Micro System on. Please consult a professional for advice before drilling any holes if you are in any doubt.
Using your Flat CD Micro System Basic use Once the disk has been read, press "play/pause “button and CD player will start play track one.
2
Using the BT (Bluetooth): The first time you use the unit or pair it to a new Bluetooth Device, pair it as follows: 1. Power on the unit from standby mode and enter to BT (Bluetooth) mode as previously instructed. “bt” will appear on the display and blink. 2. Power on the external BT Device and enter to BT searching mode. Start pairing following on screen instructions from the external BT Device. After pairing, the “bt” on the display will stop blinking. 3. Plays the music in the paired BT Device as usual.
Troubleshooting Problems No power There is no sound or the sound is distorted. Unable to play a CD. The buttons on the appliance do not work. The remote control does not work Cause(s) Solution The appliance is not correctly plugged in or the power is not turned on at the socket. The fuse in the plug has blown. Ensure the plug is correctly fitted and the power is turned on. Change the fuse in the plug. The audio cables are not correctly fitted. The volume is set to the minimal level.
Technical Specification Power Source: DC 5, 1A, Center positive Clock Back Up: 2 x 1.5 “AA” battery (included) Power source of AC/DC AC 100-240V~50/60Hz 0.4A Adaptor: Output of the AC/DC Adaptor: DC 5V, 1A, Center positive Radio Band Coverage: FM 87.5 - 108 MHz Audio Power: 1.8W per Channel Impendence of Speakers: 8 Ohm; 3W x 2 BT version: 5.