Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. RF warning for Mobile device: This equiment should be installed and operated with minimum distance 20cm bwtween the radiator & your body.
LOCATION OF CONTR0LS Top: 1. LED lights On-Off 2. Microphone Echo Knob 3. USB Port (For music playback) 4. SD Card Slot 5. ROCK Mode 6. POP Mode (Equalizer) (Equalizer) 7. FLAT(OFF)Mode (Equalizer) 8. CLASSIC Mode (Equalizer) 9. JAZZ Mode (Equalizer) 10.
11. Guitar (In) Jack 12. BASS Adjustment Knob 13. TREBLE Adjustment Knob 14. Master Volume Knob 15. Repeat Button (For USB/SD Card Mode) 16. ►►I /CH+ (Skip forward/Fast forward/Radio tuning up) Button 17. ►II/SCAN (Play-Pause/Radio Program Preset) Button 18. I◄◄ (Skip backward/Fast rewind/Radio program down) Button 19. LED Display 20. Remote Receiver 21. MODE Button 22. Microphone/Guitar Volume Knob Rear: 1. POWER ON/OFF Switch 2. DC 21V (In) Jack 3. AUX (In) Jack 4. Line out R 5. Line out L 6.
REMOTE CONTROL: 1. STOP Button (For USB/SD Mode) 2. Numeric Buttons 3. I◄◄ (Skip backward/Fast rewind/Radio program down) Button 4. Repeat button (For USB/SD Card Mode) 5. ►II/PP/SCAN 6. MODE Button 7. 10+ Button 8. VOL + (Volume Up ) Button 9. ►►I /CH+ (Skip forward/Fast forward/Radio tuning up) Button (Play-Pause/Radio Program Preset) Button 10. VOL - (Volume Down ) Button 11. MUTE Button 12. EQ Mode Select Button 13.
POWER SOURCE: Connect the small plug from the supplied AC/DC Adaptor to the DC 21V (In) Jack on the rear of unit then plug the AC/DC Adaptor to a AC wall outlet having AC 100-240V~; 50/60Hz as illustrated below: NOTES: If you will not use the unit for an extended period of time, unplug the AC/DC Adaptor from wall outlet.
Remote Control: First time use: Remove and discard the insulation film as illustrated below: Replacing the button cell when it is drained as follows: Push and slide out the button cell holder as illustrated below. Replace the button cell with new CR2025 button cell with the polarity markings on the rear of the Remote Control. Close the button cell holder. Battery precautions: Follow these Battery Precaution when using a battery in this device: 1.
battery is swallowed, it can cause severe internal burn in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. EFFECTIVE DISTANCE OF REMOTE CONTROL When there is an obstacle between the unit and the transmitter, the transmitter may not operate.
OPERATION: GENERAL OPERATION: 1. Connect the unit to AC power as previously instructed. 2. Press the POWER Switch to ON position to power on the unit, "bt" will appear on the display. 3. Press the MODE Button on the unit or Remote Control repeatedly to switch to desired playback mode.
5. Repeat Function: During USD/SD Card playback, the default setting is all tracks repeat. “RE A” will appear on the display. All the tracks will be playback repeatedly. Press the Repeat Button on the Unit or RPT Button on the Remote Control. “RE 1” will appear on the display. The current track will playback repeatedly. NB: If you will not use the unit for an extended period of time, press the POWER Switch to OFF position to power off the unit then unplug the AC/DC Adaptor from AC wall outlet.
will appear on the display and blink. 3. Wait a few seconds until the unit is automatically paired to the external BT Device. The indicator “bt” on the display will stop blinking. 4. After pairing is complete you may now play music with your external BT Device. FM RADIO: 1. Power on the unit as previously instructed. 2. Press the MODE Button on the Unit or Remote Control repeatedly indicator Radio frequency “XX.X MHz” will appear on the display. 3.
the connected Audio Player is turned to high level.) USB: To play the music in external USB Device: 1.Insert the USB Device into the USB Port on the top of unit as illustrated below: 2. Power on the unit as previously instructed. 3. The unit will automatically play the first track on the USB Device. 4. During playback: Press the ►II/SCAN Button on the unit or Remote Control to pause, press again to resume normal playback. Short Press the I◄◄ or ►►I buttons repeatedly to skip tracks.
will appear on the display then the unit will start to play it. To play the 14th track on the USB device, press the “4” + “10+” buttons. “0014” will appear on the display then the unit will start to play it. Notes: When inserting the USB Device, make sure the direction you selected is correct. Never insert violently to avoid damaging the USB Device or the unit. You also need to download the desired music in MP3 format into the USB Device before insert into the unit.
2. Power on the unit as previously instructed. 3. The unit will automatically play the first track on the SD CARD Device. 4. During playback: Press the ►II/SCAN Button on the unit or Remote Control to pause, press again to resume normal playback. Short Press the I◄◄ or ►►I buttons repeatedly to skip tracks. Long Press the I◄◄ or ►►I buttons to search the specific section . Use the Numeric & 10+ buttons on the Remote Control to select and plays the desired tracks.
Connect microphone: -Insert the cord of the microphone supplied into the MIC IN. plug on the top of the speaker as illustrated below: -Use the MIC/GT.VOL knob to select the desired microphone volume. -Use the M.ECHO knob to set any desired echo sound effect for the microphone.
Line out: As illustrated below, you can connect an external amplifier ( sound bar,active speaker etc.) to the party speaker via the LINE OUT connection on the rear panel.
TROUBLESHOOTING: Check the following before requesting service: SYMPTOM No power POSSIBLE CAUSE POSSIBLE SOLUTION AC/DC Adaptor had not Connected the AC/DC connected Adaptor to the unit and AC power as page 8 Volume of the unit was set to Increase the volume level minimum position by turning the VOLUME Control Knob on the unit clockwise and press the VOL + Button on the No sound or sound weak Remote Control.
Radio not function Unit not in radio mode Press the MODE Button on the Unit or Remote Control repeatedly until Radio frequency “XX.X” or “XXX.
GENERAL SPECIFICATTIONS: Power Source: DC 21V, 3.42A, Audio Power: Total 70W, RMS Impedance of Speakers: 40W, 6Ω FM Band Converge: 87.5 – 108MHz BT Version: 5.