DVD/CD PLAYER Hi-Fi STEREO VIDEO CASSETTE RECORDER USER'S GUIDE For model: HR-XVC25U For Customer Use: Enter below the Model No. and Serial No. which are located on the rear of cabinet. Retain this information for future reference. Model No. Serial No.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
IMPORTANT SAFEGUARDS 1. READ INSTRUCTIONS All the safety and operating instructions should be read before the unit is operated. 2. RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference. 3. HEED WARNINGS All warnings on the unit and in the operating instructions should be adhered to. 4. FOLLOW INSTRUCTIONS All operating and use instructions should be followed. 5. CLEANING Unplug this unit from the wall outlet before cleaning.
IMPORTANT SAFEGUARDS 13. LIGHTNING To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surges. 14. POWER LINES An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits.
IMPORTANT SAFEGUARDS / Power source 25. LASER BEAM Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the laser beam. It may cause sight damage. 26. DISC Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personal injury and product malfunction. 27.
Features DVD/CD Player/Video Cassette Recorder • DVD/CD player with Video Cassette Recorder - Unique space saving design combines a DVD/CD player and a Hi-Fi Video cassette recorder. The DVD disc has much more capacity, but is the same size as the audio CD disc. Picture quality is higher than Super VHS. Audio quality is higher than audio CD. • High Quality Picture - More than 500 lines (VCR mode: 230 lines) of Horizontal Resolution. It exceeds Super VHS (400 lines) or Laser Disc (430 lines) in resolution.
Contents Before using your unit Disc Playback operation IMPORTANT SAFEGUARDS .......................... 3 Power source ................................................... 5 Features ........................................................... 6 Contents ........................................................... 7 Parts and functions .......................................... 8 Display ............................................................. 9 Remote control ...........................................
Parts and functions Front STOP button VCR/DVD mode selector button Cassette Loading Slot OPEN/CLOSE button PLAY button Disc tray EJECT button Remote sensor POWER button CHANNEL +/– buttons AUDIO (L/R)/ VIDEO IN jacks DVD indicator REW (Rewind) button VCR indicator REC button FF (Fast Forward) button Rear DVD COAXIAL DIGITAL AUDIO OUT jack AC power cord RF IN jack DVD S-VIDEO OUT jack S-VIDEO/COMPONENT Video selector switch RF OUT jack DVD AUDIO (L/R) OUT jacks DVD OPTICAL DIGITAL AUDIO OUT
Display Display window 1 2 3 4 12 5 6 11 No. 1 10 9 8 7 Display VCR Description VCR mode 2 Playback (lights) / Auto resume (flashes) 3 Still picture 4 DVD DVD disc is inserted. 5 CD CD is inserted.
Remote control TV/VCR/DVD switch POWER DVD MENU MARKER RETURN OPEN/CLOSE DISPLAY SUBTITLE A.TRK ANGLE C. RESET SEARCH MODE ZERO RETURN PLAY MODE SP/EP ZOOM TITLE REPEAT A-B 0-9 TV Multi-Brand Remote Control This Remote can control some functions (TV POWER, NUMBER(0-9), INPUT, TV VOL +/–, TV CH +/– and ENTER) of a remote controllable TV of JVC and the brands listed on page 12 by slide TV/VCR/DVD switch to TV. (The POWER button on the upper right is not effective for the TV.
Remote control Inserting Batteries 1 Open the battery compartment cover in the direction of the arrow. two “AA” batteries (supplied), 3 2 Install paying attention to the polarity Replace the compartment cover. diagram in the battery compartment. Battery precautions The precautions below should be followed when using batteries in this device: 1. Use only the size and type of batteries specified. 2.
TV multi-brand remote control The DVD/VCR’s remote control can control several functions on JVC remote control TVs and on the brands of remote control TVs listed below. Preparation: • Turn the power off the TV using theTV’s remote control. • Make sure TV/VCR/DVD switch has been slided to TV. and hold VCR on the remote control until you finish the 1 Press step 2. your TV’s brand code using the Number keys, then 2 Enter press ENTER.
Control four JVC VCRs The remote control is capable of controlling four JVC VCRs independently; one set to respond to your remote control’s A code control signals and the other set to respond to B, C, D code control signals. The remote control is preset to send A code signals because your DVD/VCR is initially set to respond to A code signals. You can easily modify your DVD/ VCR to respond to the other code signals. Preparation: Make sure TV/VCR/DVD switch has been slided to VCR/DVD.
Basic connections If you are using an antenna system, follow these instructions. If you are a cable (CATV) subscriber, skip ahead to page 16 for the proper connections. ANTENNA TO DVD/VCR CONNECTION The DVD/VCR must be connected “between” the antenna and the TV. First, disconnect the antenna from the TV and connect it to the DVD/VCR. Then connect the DVD/VCR to the TV. Below are 3 common methods of connecting an antenna system to a DVD/VCR.
Basic connections DVD/VCR TO TV CONNECTION After you have connected the antenna to the DVD/VCR, you must connect the DVD/VCR to the TV. Below are 3 common methods of connecting your DVD/VCR to a TV. Find the type of TV you are using and follow the connection diagram. This DVD/VCR has a single 75 ohm output for connection to a TV. If your TV has separate VHF and UHF antenna inputs (numbers 2 and 3 below), use a splitter to connect the DVD/VCR to the TV for VHF and UHF reception.
CATV (CABLE TV) connections Many cable companies offer services permitting reception of extra channels including pay or subscription channels. This DVD/VCR has an extended tuning range and can be tuned to most cable channels without using a cable company supplied converter box, except for those channels which are intentionally scrambled. If you subscribe to a special channel which is scrambled, you must have a descrambler box for proper reception.
CATV (CABLE TV) connections IMPORTANT: Make sure the TV/CATV menu option is set to the “CATV” mode. This DVD/VCR cannot receive scrambled programs since it does not contain a descrambler. In order to receive scrambled programs, your existing descrambler must be used. Descrambler boxes are available from cable companies. Consult your local cable company for more information concerning connection to their descrambler equipment. There are many ways to connect your DVD/VCR to a cable system.
Playback connections The exact arrangement you use to interconnect various video and audio components to the DVD/VCR is dependent on the model and features of each component. Check the Owner's Manual provided with each component for the location of video and audio inputs and outputs. Connect to a TV with Audio/Video Output You can enjoy playback by simply connecting the unit to a TV. Connect the unit to a TV equipped with stereo audio input and video input jacks using the supplied audio/video cable.
Playback connections Connect to a Stereo Amplifier with Audio Output You can enjoy high-quality audio by connecting the unit’s audio output to your amplifier. Connect the unit’s AUDIO OUT jacks to any line-level inputs (such as AUX, DVD, CD, etc.) of an audio amplifier.
Setting the video channel/Setting the language Setting the Video Channel When a TV is connected with the 75 ohm coaxial cable only. To view playback of a recorded tape, or to watch a program selected by the VCR's channel selector, the TV must be set to channel 3 or 4 (video channel). and hold 3 or 4 on the remote for 3 seconds in standby 1 Press mode. The video channel will start to flash for 3 seconds in the display window. 2 Press POWER to turn on the DVD/VCR. TV/VCR/DVD switch to VCR/DVD.
Tuner setting This DVD/VCR is equipped with a channel memory feature which allows channels to skip up or down to the next channel set into memory, skipping over unwanted channels. Before selecting channels, they must be programmed into the DVD/VCR’s memory. In addition to normal VHF and UHF channels, this DVD/ VCR can receive up to 113 Cable TV channels. To use this DVD/VCR with an antenna, set the TV/CATV menu option to the TV mode. When shipped from the factory, this menu option is in the CATV mode.
To ADD/DELETE channels/Noise elimination To ADD/DELETE channels You can add the channels you want or delete the channels you do not want manually. Preparation: • Turn ON the TV and set it to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press VCR to select the VCR mode. (The VCR indicator will light.) the step 1 on page 21. 1 Repeat or to select the Then press CH SETUP TV CATV AUTO CH MEMORY ADD/DELETE “ADD/DELETE” option and press ENTER.
Auto clock setting The Auto Clock feature enables the automatic clock setting and updating, and also to set the Time Zone and Daylight Saving Time by receiving XDS (Extended Data Service) information carried on the channel signal. Preparation: • You must set the antenna connection before the AC cord plug is inserted into the AC outlet. • Make sure the AUTO CH MEMORY (on page 21) is done.
Auto clock setting Daylight Saving Time setting You can set the Daylight Saving Time automatically or manually. Preparation: • Turn ON the TV. • When a TV is connected with an audio/video cable, select the video input mode on the TV. • When a TV is connected only with an antenna cable, set to the video channel 3 or 4. Then select VCR position with TV/VCR. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press VCR to select the VCR mode. (The VCR indicator will light.
Manual clock setting You must set the date and time manually for timer recordings and Daylight Saving Time if the Auto Clock process did not set them correctly. Preparation: • Turn ON the TV and set to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press VCR to select the VCR mode. (The VCR indicator will light.) EXAMPLE: Setting the clock to “8:30 AM” March, 26 (WED), 2003. 1 Press SET UP MENU. The VCR menu screen will appear.
Loading and Unloading a cassette tape Use only video cassette tapes marked and . • Cassettes marked “VHS” (or “S-VHS”) can be used with this video cassette recorder. However, S-VHS recording is not possible with this model. • This model is equipped with SQPB (S-VHS QUASI PLAYBACK) that makes it possible to play back S-VHS recordings with regular VHS resolution. • HQ VHS is compatible with existing VHS equipment. Loading Push the center of the tape until it is automatically inserted.
Cassette tape playback Preparation: • Turn ON the TV and set to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press VCR to select the VCR mode. (The VCR indicator will light.) a prerecorded tape 1 Load (When loading a cassette tape without the erase prevention tab, playback will start automatically). start playback 2 To Press PLAY. Playback will start. “ ” will appear on the screen for about 4 seconds. To stop playback Press STOP once.
Special playback Picture Search Repeat playback Reverse picture search function Press REW x 1 or x 2 during the playback. The entire video tape will be played until its end.The tape will then automatically rewind to the beginning and the playback will be repeated. Forward picture search function Press FF x 1 or x 2 during the playback. To return to playback: Press PLAY. SET UP 1 Press MENU. Press Still Picture Press PAUSE during playback. To resume normal playback: Press PLAY.
ZERO RETURN function/Video Index Search system ZERO RETURN function This function makes tape-rewinding stop at the counter 00:00:00 position automatically. OSD. 1 Press The counter display shows the tape 8 : 47AM MON HI - FI running time during playback or recording. VCR Press C. RESET at the desired tape po2 sition. The counter display will be reset to the “00:00:00” position (e.g. the begining of recording).
Recording a TV program Recording and viewing the same TV program Preparation: • Turn ON the TV and set it to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press VCR to select the VCR mode. (The VCR indicator will light.) a cassette tape with the erase 1 Load prevention tab intact. The VCR will automatically turn on. SP/EP to select the desired tape 2 Press speed SP or EP. The tape counter and “SP” or “EP” will appear on the screen for about 4 seconds.
Recording a TV program To stop recording Press STOP to stop recording. “ ” will appear on screen for about 4 seconds. To stop recording temporarily Press PAUSE to avoid recording unwanted material. Press again to continue the recording. “ ” will appear on screen for about 4 seconds. NOTES: • The pause function will be released after 5 minutes to prevent damage to the tape or the VCR. The VCR will change to the STOP mode. • You can select a recording channel in the recording pause mode.
Instant Timer Recording (ITR) The Instant Timer Recording feature provides a simple and convenient way to make a timed recording. Preparation: • Turn ON the TV and set it to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press VCR to select the VCR mode. (The VCR indicator will light.) Example: Instant Timer Recording for 30 minutes. a cassette tape with the erase 1 Load prevention tab intact. The VCR will automatically turn on.
Timer recording Timer recording can be programmed on-screen with the remote control. The built-in timer allows automatic unattended recording of up to 8 programs within 1 month. Preparation: • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press VCR to select the VCR mode. • Load a cassette tape with the erase prevention tab intact. • Press OSD to verify time and date are correct (see page 31).
Timer-recording Timer recording special case Weekly (e.g. WKL-TU: each Tuesday) or daily (e.g. MO-SA: Monday to Saturday) timer recording Follow the procedure of timer recording on the previous page. At picture 3 press SET + or – repeatedly until the desired setting appears. Then press ENTER. When you press SET – repeatedly, the indicator at DATE will change as follows, in this case the today is Friday.
Stereo recording and playback/Separate Audio Program (SAP) Stereo Recording and Playback The VHS Hi-Fi audio system permits high fidelity recording of MTS STEREO TV broadcasts. When a MTS STEREO broadcast is received, the word “STEREO” will appear on the screen for about 4 seconds and the program can be viewed or recorded in stereo. The Hi-Fi STEREO recording procedure is the same as for normal recordings.
Duplicating a video tape/Duplicating a disc material onto a video tape Duplicating a video tape If you connect the VCR to another VCR or camcorder, you can duplicate a previously recorded tape. Make all connections before turning on the power. a blank cassette tape with the erase prevenREC on the recording VCR or on the Remote. 1 Load 4 Press tion tab intact into the recording VCR. While holding REC, press PLAY. Load a previously recorded tape into the playback VCR or CAMCORDER. Then press PAUSE.
Disc The following types of discs can be played on this unit. Disc type and logo mark Recorded content DVD Video Audio + Video Video CD Audio CD Audio • This unit can play back FUJICOLOR CD and Kodak Picture CD formats. • DVD-ROM, SVCD, CVD, Photo CD, etc. cannot be played. • Some CD-R/RWs can not be played back depending on the recording conditions. • This unit is to be used exclusively with the NTSC color system. PAL and SECAM system discs cannot be used with this unit.
Setting setup language The setup language can be selected. Preparation: • Turn ON the TV and set it to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. • When using an amplifier, switch on the amplifier. DVD to select the DVD 1 Press mode. (The DVD indicator will Reading light.) “No Disc” will appear on the screen. (If a DVD disc has already loaded, the playback will start automatically.) Press SET UP MENU in the stop 2 mode.
Playback procedure Preparation: • Turn ON the TV and set it to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light.) OPEN/CLOSE. 1 Press The disc tray will open. a disc onto the tray. 2 Place Hold the disc, position it with the printed label side up, align it with the guides, and place it in its proper position. OPEN/CLOSE or PLAY. 3 Press The disc tray closes automatically.
Special playback Note: There may be a slight delay between pressing the button and the function activation. Fast Forward Playback Press FF during normal playback. Each press of FF will increase the speed of the search (x4), (x8), (x20). (x2), • To resume normal playback, press PLAY. Review Playback Press REW during normal playback. Each press of REW will increase the speed of the search (x4), (x8), (x20). (x2), • To resume normal playback, press PLAY.
Zooming/Locating desired scene Preparation: • Turn ON the TV and set it to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light.) Zooming This unit will allow you to zoom in on the frame image. You can then make selections by switching the position of the frame. ZOOM during playback. 1 Press The center part of the image will 1 be zoomed in. Each press of ZOOM will change 1 (x 1.3), 2 (x the ZOOM 3 (x 2.0). 1.
Repeat playback Preparation: • Turn ON the TV and set it to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light.) Repeat playback of Title, Chapter and Track 1 Press PLAY MODE during playback or stop mode. DVD CD Repeat : Off /Enter/Play Mode Play Mode : Off Repeat : Off /Enter/Play Mode ENTER once or twice to select “Chapter” or “Title”.
Program playback/Random playback (CD) Preparation: • Turn ON the TV and set it to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light.) Program playback You can arrange the order of tracks on the disc. PLAY MODE in the stop 1 Press mode. ENTER repeatedly until 2 Press the Program table as right appears.
MP3/WMA/JPEG playback This player can play back the MP3/WMA/JPEGdata which has been recorded on CD-R or CDRW. To produce the MP3/WMA/JPEG-data, you need a Windows-PC with CD-ROM drive and a MP3/WMA/JPEG-encoding Software (not supplied). The Apple-HFS-System can not be played. MP3/WMA/JPEG CD information Limitations on MP3/WMA/JPEG CD playback • MP3/WMA/JPEG CD is the disc that is standardized by ISO9660, its file name must include 3-digits extension letters, “mp3”, “wma”, “jpg”.
Preparation: • Turn ON the TV and set it to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light.) JPEG CD playback OPEN/CLOSE. 1 Press The disc tray will open. Place a disc on which JPEG files have been recorded onto the tray. OPEN/CLOSE or PLAY. 2 Press The disc tray closes automatically. Reading On the TV-screen, “Reading” will appear. Reading will take as much time as the number of file.
Setting the JPEG Interval Preparation: • Turn ON the TV and set it to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light.) Setting the JPEG Interval You can continuously play back all JPEG files automatically. SET UP MENU in the 1 Press stop mode. Press / then press Language Picture Sound Parental Other to select “Picture”, or ENTER. /Enter/Setup/Return or 2 Press Interval”.
Setting the Select Files When playing back a CD containing a mixture of MP3, WMA and JPEG files, only MP3/WMA or JPEG files can be displayed on the file menu. Preparation: • Turn ON the TV and set it to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light.) SET UP MENU in the 1 Press stop mode. Press / then press Language Picture Sound Parental Other to select “Picture”, or ENTER.
Zooming/Changing angles (JPEG CD) Preparation: • Turn ON the TV and set it to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light.) Zooming This unit will allow you to zoom in on the JPEG image. ZOOM during playback. 1 Press Enlarged JPEG images are displayed. You can make the images even larger by repeatedly pressing ZOOM. 1 2 Off 3 mode, press ZOOM repeatedly to return to a 1:1 2 Inviewthe( zoom Off).
Marking desired scenes The unit stores the points that you want to watch again up to 3 points. You can resume playback from each scene. Preparation: • Turn ON the TV and set it to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light.) Marking the scenes MARKER during 1 Press playback. Marker 1 Marker 2 Marker 3 /Enter/Cancel/Marker the blank Marker using 2 Select / .
Changing soundtrack language/Karaoke playback Preparation: • Turn ON the TV and set it to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light.) Changing soundtrack language You can select the language when you play a multilingual disc. A.MONITOR 1 Press playback. during 2/8 Fra Dolby Digital The current soundtrack language will appear. A.MONITOR repeatedly 2 Press until the desired language is selected.
Subtitles/Changing angles/Title selection/DVD menu Preparation: • Turn ON the TV and set it to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light.) Turning the Subtitles On and Off When playing back a disc recorded with subtitles, you can turn the subtitles on or off. Press SUBTITLE during playback Off until “Off” appears.
Parental control Some discs are specified not suitable for children. Such discs can be prevented from play back with the unit. Preparation: • Turn ON the TV and set to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light.) Parental control setting SET UP MENU in the stop mode. 1 Press Press or to select “Parental”. Then press or ENTER.
Temporary disabling of rating level by DVD disc Depending on the DVD disc, the disc may try to temporarily cancel the rating level that you have set. It is up to you to decide whether to cancel the rating level or not. Preparation: • Turn ON the TV and set to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light.) a DVD disc and press 1 Load OPEN/CLOSE or PLAY (see page 39).
Setting menu language You can select the language of the disc menu messages of DVDs. Preparation: • Turn ON the TV and set to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light.) SET UP MENU in the stop 1 Press mode. Press or “Language”. Language Picture Sound Parental Other to select /Enter/Setup/Return or ENTER. 2 Press Then press or to select “Menu”.
Setting subtitle language The same subtitle language can always be selected even if you replace the disc or turn the power off. Preparation: • Turn ON the TV and set to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light.) SET UP MENU in the stop 1 Press mode. or Press “Language”. Language Picture Sound Parental Other to select /Enter/Setup/Return or ENTER.
Setting audio soundtrack language/Setting surround sound Setting audio soundtrack language The same audio soundtrack language can always be selected by your unit even if you replace the disc or turn the power off. Preparation: • Turn ON the TV and set to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light.) SET UP MENU in the stop 1 Press mode.
Setting the aspect ratio of TV screen You can select the aspect ratio for your TV. Preparation: • Turn ON the TV and set to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light.) SET UP MENU in the stop 1 Press mode. Press or Language Picture Sound Parental Other to select “Picture”. /Enter/Setup/Return 2 Pressor or ENTER, then press to select “Tv Screen”.
Setting on screen display/Status display of disc On screen display can be switched on or off when you press the buttons. Preparation: • Turn ON the TV and set to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light.) SET UP MENU in the stop 1 Press mode. or Press Language Picture Sound Parental Other to select “Picture”. /Enter/Setup/Return or ENTER, then press 2 orPress to select “Display”.
Dynamic Range Control DRC (Dynamic Range Control) enables you to control the dynamic range so as to achieve a suitable sound for your equipment. Preparation: • Turn ON the TV and set to the video input mode. • Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press DVD to select the DVD mode. (The DVD indicator will light.) SET UP MENU in the stop mode. 1 Press Press or to select “Sound”. Language Picture Sound Parental Other /Enter/Setup/Return or ENTER to Press 2 select “DRC”.
Progressive scan The unit supports the Progressive scanning system as well as the conventional interlaced scanning system. If your television or monitor equipped with component jacks support the progressive video input, you can enjoy a high quality picture by making the Progressive scanning mode active. Preparation: • Connect to a TV equipped with component jacks. • Turn On the TV and set it to the corresponding video input mode.
Language code list Enter the appropriate code number for the initial settings “Audio”, “Subtitle” and/or “Menu” (see pages 5456).
Problems and troubleshooting Use the following check list for troubleshooting when you have problems with your unit. Consult your local dealer or service outlet if problems persist. Be sure all connections are properly made when using with other units. SYMPTOMS POSSIBLE SOLUTIONS PAGE DVD/VCR DVD/VCR does not operate. • Make sure the power cord is plugged in. • Try another AC outlet. • Power is off, check fuse or circuit breaker. • Unplug unit, then plug it back in.
Problems and troubleshooting/Video head cleaning SYMPTOMS POSSIBLE SOLUTIONS PAGE No picture, or the screen is blurred • The S-VIDEO/COMPONENT selecter is not set correctly. • The progressive scanning mode is active through the unit is or divided into two parts. connected to a TV via the VIDEO OUT jack. 18 60 Stopping playback, search, slowmotion play, repeat play, or program • Some discs may not do some of the functions. play, etc. cannot be performed.
Specifications GENERAL Power supply: Power consumption: Weight: Dimensions: AC 120V 60Hz Operation: 18W Stand by: 2W 7.9lbs (3.
FOR SERVICING (Only in U.S.A.) HOW TO LOCATE YOUR JVC SERVICE CENTER TOLL FREE: 1-800-537-5722 http://www.jvc.com Dear Customer, In order to receive the most satisfaction from your purchase, please read the instruction booklet before operating the unit. In the event that repair is necessary, or for the address nearest your location within the Continental United States, please call 1-800-537-5722 for your nearest authorized servicer or visit our website at www.JVC.com.
WARRANTY (Only in U.S.A.) LIMITED WARRANTY CONSUMER VIDEO 1-90 JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original retail purchase for the period as shown below. (“The Warranty Period”) THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND IN COMMONWEALTH OF PUERTO RICO.
MEMO ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
VICTOR COMPANY OF JAPAN, LIMITED J2C51201B U 03/05 68 Printed in Thailand 0503-AH-OR-OR
