LCD Flat Panel TELEVISION Operating Guide for L47S601 & L42S601 IMPORTANT SAFETY INSTRUCTIONS .................................................................................................. 2-3 FIRST TIME USE .................................................................................................................................... 4-21 THE REMOTE CONTROL .................................................................................................................... 22-33 ON-SCREEN DISPLAY ..
Important Safety Instructions SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HITACHI LCD FLAT PANEL TELEVISION Our reputation has been built on the quality, performance, and ease of service of HitachiI LCD Flat Panel televisions. Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this section illustrates safety tips which will be of benefit to you.
Important Safety Instructions Power source This LCD television is designed to operate on 120 volts 60 Hz, AC current. Insert the power cord into a 120 volt 60 Hz outlet. The mains plug is used as the disconnect device and shall remain readily operable. Public viewing of copyrighted material Public viewing of programs broadcast by TV stations and cable companies, as well as programs from other sources, may require prior authorization from the broadcaster or owner of the video program material.
Accessories Check to make sure you have the following accessories before disposing of the packing material. 쐇 Two “AA” size, 1.5V batteries 쐋 Power Cord First time use 쐃 Remote Control 쐏 Power Swivel Cable For U.S. models: For optional accessories, please access our web site at: www.hitachi.us/tv For Canada models: For optional accessories, please access our web site at: www.hitachi.ca/tv CAUTION: 1. Ceiling mounting is not recommended.
How To Set Up Your New Hitachi LCD Television To take measures to prevent the LCD Flat Panel Television from tipping over and prevent possible injury it is important to mount the unit in a stable and flat surface. Wire ANTENNA Unless your LCD Television is connected to a cable TV system or to a centralized antenna system, a good outdoor color TV antenna is recommended for best performance.
How to set up your new Hitachi LCD Television AC CORD AND POWER SWIVEL CABLE INSTALLATION INSTRUCTION First time use The AC cord and power swivel cable provided with your new LCD Flat Panel Television need to be installed correctly to avoid their disconnection when rotating the TV on its Table top stand. Located on the back of the TV are 2 plastic clamps to hold the AC cord and power swivel cable. Please follow the instructions below. 쐃 Pass the AC cord through Clamp #1 and connect it to the TV.
How to set up your new HITACHI LCD Television SETTING FOR WALL MOUNTING First time use STEP (1) : Please locate the STAND METAL SUPPORTS on the back of the TV . These metals is use to hold the TV and the Base ; so it needs to remove 4 screws from the STAND METAL in order to separate the TV from the Base. 2 STAND METAL SUPPORTS Remove 4 screws then remove the 2 metal supports. STEP (2): Now please remove the 5 screws of the STAND metal from the TV, now the TV STAND can be separated from the TV.
How to set up your new HITACHI LCD Television VIEWING First time use The best picture is seen by sitting directly in front of the TV and about 10 to 18 feet from the screen. During daylight hours, reflections from outside light may appear on the screen. If so, drapes or screens can be used to reduce the reflection or the TV can be located in a different section of the room.
Hook-up Cables and Connectors First time use Most video/audio connections between components can be made with shielded video and audio cables that have phono connectors. For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be purchased from most stores that sell audio/video products. Below are illustrations and names of common connectors.
Quick Reference Remote Control Buttons and Functions First time use In addition to controlling all of the functions on your HITACHI LCD TV, the new remote control is designed to operate different types of devices, such as, DVD Players, CBL (Cable Boxes), set-top-boxes, satellite receivers, and VCRs. The remote control must be programmed to control the chosen device. Please see pages 22-33 for a complete description of all features and programming of the Remote Control.
Side Panel Controls 햲 햶 SIDE PANEL CONTROLS 햷 First time use 햵 햳 FRONT VIEW 햻 햴 햺햹 햸 햲 SIDE POWER button Press this button to turn the LCD Television ON/OFF. It can also be turned ON/OFF by remote control. The “MAIN POWER” can only be turn OFF by unplugging the power cord from the outlet. After this button is pressed to turn ON the set, the function of this button will not be available for a short period of time until the picture appears on the TV screen.
Side Panel Controls First time use 햹 POWER light indicator To turn the TV ON, press the power button located on the right side of the TV set. A red stand-by indicator lamp located on the lower right corner of the front bezel is illuminated. The LCD TV is now ready for remote ON/OFF operation. 햺 R/C sensor 햹 Indicating Lamp Indicating Lamp Power Status Operating Off OFF. When the TV set is unplugged from AC line. Lights Red OFF. (Stand-by) When the TV set is plugged to the AC line.
Rear Panel Connections 햲 Antenna Input To switch between Cable and Air input, go to the Channel Manager option to change the signal source CABLE or AIR. 햹 햺햶 햸 First time use 햳 Audio/Video Inputs 1, 2 and 3 By using the INPUTS button, the CURSOR PAD ( and ), and the SELECT button or CURSOR PAD of the remote control, you can select each video source. Use the audio and video inputs to connect external devices, such as VCRs, camcorders, laserdisc players, DVD players etc.
Connecting External Video Sources The SIDE panel jacks are provided as a convenience to allow you to easily connect HDMI or DVI signals from a DVD, Set Top Box , Video Game as shown in the following examples (When connecting DVI signal it will need to connect the audio output into the side Audio Input jacks) : First time use A) Connecting HDMI signal. SIDE INPUT PANEL Note : Special device cables will be according to the own device specifications.
Connecting External Video Sources The SIDE panel jacks are provided as a convenience to allow you to easily connect a camcorder , DVD, Video Game and a VCR as shown in the following examples: SIDE INPUT PANEL First time use Video Game COMPOSITE VIDEO OUTPUT CAPABILITY DVD , Video Game Console. R OUTPUT L Note : For Monoaural devices, please connect Audio signal cable into L/Mon o input jack . Video Video Camera Note : Special device cables will be according to the own device specifications.
First time use Rear Panel Connections DIGITAL OUTPUT CAPABILITY VCR #2 HDMI DIGITAL OUTPUT CAPABILITY HDMI OUTPUT DIGITAL OUTPUT S-VIDEO V L INPUT R AUDIO OUT HDMI to HDMI DVI to HDMI Optional DVD Player OUTPUT Y PB/C B PR /CR L R Outside Antenna or Cable TV coaxial cable Optional Y P B PR L OUTPUT R OUTPUT S-VIDEO V L VCR #1 16 ANT IN 2-Way signal splitter HDTV Set-Top Box NOTE: Cables are optional, except when specified.
Tips on Rear Panel Connections • S-VIDEO, Y-PBPR, or HDMI connections are provided for high performance laserdisc players, VCRs etc. that have this feature. Use these connections in place of the standard video connection if your device has this feature. First time use • If your device has only one audio output (mono sound), connect it to the left audio jack on (L/(MONO)) the Rear Panel.
Connecting External Video Sources CONNECTING A VIDEO AND STEREO AUDIO SOURCE TO INPUT1 ~ INPUT-FRONT First time use 1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the Rear Panel to the right. 2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack. 3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack. 4.
Connecting External Video Sources CONNECTING A COMPONENT SOURCE WITH HDMI OR DVI CAPABILITY TO HDMI 1, HDMI 2 OR HDMI FRONT 2. With DVI output, connect the cable from the AUDIO OUT R of the HDTV set top box or DVD player to the INPUT (AUDIO/R) jack as shown on the Rear Panel below. 3. With DVI output, connect the cable from the AUDIO OUT L of the HDTV set top box or DVD player to the INPUT (AUDIO/L) jack as shown on the Rear Panel below. 4.
Connecting External Audio/Video Devices First time use CONNECTING A COMPONENT AND STEREO AUDIO SOURCE TO INPUT 2 or 3 :Y-PBPR. 1. Connect the cable from the Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (Y) jack, as shown on the Rear panel below. 2. Connect the cable from the PB/CB OUT or BY OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (PB) jack. 3.
Connecting External Audio/Video Devices CONNECTING A VIDEO AND MONAURAL AUDIO SOURCE TO INPUT 1 ~ FRONT INPUT First time use 1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the Rear Panel on the right. 2. Connect the cable from the AUDIO OUT of the VCR or the laserdisc player to the INPUT (MONO)/L(AUDIO) jack. 3.
The Remote Control In addition to controlling all the functions on your Hitachi LCD TV, the new remote control is designed to operate different types of VCRs, cable boxes, set-top-boxes, satellite receivers, DVD players, and other audio/video equipment with one touch. Basic operation keys are grouped together in one area. The Remote Control To operate your LCD TV, select TV by pressing the Source button of the Source Select on the remote.
How to Use the Remote to Control Your TV 쐃 POWER button Press this button to turn the TV set on or off when the remote is in TV mode. (See page 22 for instructions on how to set the remote control to TV mode). 쐃 쐇 쐋 쐇 MODE Indicator Turns on or blinks three times to show remote control mode. 쐋 SOURCE SELECT button Press this button to select remote control mode.
How to Use the Remote to Control Your TV 쐄 ASPECT button Press this button to quickly change the picture format ASPECT ratio. Depending on the input signal format received, the picture format ratio allows you to adjust the images through the following options. 4:3 STANDARD Use this aspect mode to display conventional (4:3) images. Side panels (gray areas) are placed to the left and right of the image to preserve the original aspect ratio of the source.
How to Use the Remote to Control Your TV 쐂 MENU button The MENU button will start the On-Screen Display. 쐆 EXIT button This button will exit all On-Screen Displays. 쐊 INPUTS button When the remote control is in TV mode, press this button to access the INPUTS menu. Use the CURSOR and SELECT buttons to scroll and select the inputs that are being used. Pressing the INPUTS button repeatedly will also cycle through the Inputs menu items. Then press the SELECT button to select.
How to Use the Remote to Control Your TV 씉 VOLUME (VOL), MUTE button Press the VOLUME button ( or ) until you obtain the desired sound level. Press the FAV CH button to switch to Favorite (FAV) channel mode. You will know you are in Favorite Channel mode when (FAV) is displayed and the displayed channel is GREEN. Press it again to return to your regular tuned channels.
The Remote Control for Cable Box Functions OPERATING THE PRECODED FUNCTION FOR YOUR CABLE BOX. 햲 This remote is designed to operate different types of cable boxes. You must first program the remote to match the remote system of your cable box (refer to pages 32-33 for pre-codes). 1. Turn ON your cable box. 햳 햲 햲 2. To switch to Cable (CBL) pre-coded mode, use the SOURCE SELECT button on the remote control to position the LED light to the corresponding selection SAT/CBL. 햳 햳 3.
The Remote Control for Set-Top-Box/Satellite Receiver Functions OPERATING THE PRECODED FUNCTION FOR YOUR SET-TOP-BOX/SATELLITE RECEIVER. 햲 This remote is designed to operate different types of set-top-box/satellite systems. You must first program the remote to match the remote system of your settop-box/satellite systems (refer to pages 32-33 for precodes). 햳 1. Turn ON your set-top-box/satellite systems. The Remote Control 2.
The Remote Control for DVD Functions OPERATING THE PRECODED FUNCTION FOR YOUR DVD PLAYER. 햲 This remote is designed to operate different types of DVD players. You must first program the remote to match the remote system of your DVD player (refer to pages 32-33 for pre-codes). 햲 햳 1. Turn ON your DVD player. 햲 햳 2. 햳 햳 3. Hold down the SOURCE SELECT button on the remote and enter the four digit preset code that matches your DVD player, as shown on pages 32-33. Release the SOURCE SELECT button.
The Remote for VCR/PVR Functions OPERATING THE PRECODED FUNCTION FOR YOUR VCR/PVR (Personal Video Recorder). 햲 This remote is designed to operate different types of VCRs/PVRs. You must first program the remote to match the remote system of your VCR/PVR (refer to pages 32-33 for pre-codes). 햲 햳 1. Turn ON your VCR/PVR. The Remote Control 2. To switch to VCR/PVR pre-coded mode, use the SOURCE SELECT button on the remote control to position the LED light to the corresponding selection PVR/VCR. 3.
How to Use the SOURCE SELECT Button INPUT ACCESS This optional feature allows the user of the remote control to setup it’s SOURCE SELECT button to access the specified input of the TV. Setup for this feature is applicable to the remote control’s normal mode only and only applies to the DVD, PVR/VCR and SAT/CBL modes. 1. Select the desired device mode (DVD, PVR/VCR, SAT/CBL) by using your SOURCE SELECT button to position the LED indicator to the corresponding selection. , , , , 3.
Remote Control Codes Cable BRAND Codes ABC ........................ 0003,0008,0011 Americast ................ 0899 Amino ...................... 1602 Bell South ............... 0899 Clearmaster ............ 0883 ClearMax ................ 0883 Coolmax ................. 0883 Digeo ...................... 1187 Director ................... 0476 General Instrument.. 0476,0810,0276,0003, 0011 GoldStar................... 0144 Hamlin ..................... 0009,0273 Hitachi ..................... 0011,1421 i3 Micro ..
Remote Control Codes DBS/PVR Combo BRAND Codes Hughes Network Systems 0739 Philips Samsung 0739 PVR BRAND ABS Alienware CyberPower Dell DirecTV Gateway Hewlett Packard Howard Computers HP 0739 Codes Accurian Advent Aiwa Akai Alco Allegro Amphion Media Works AMW Apex Digital 0739 1972 1972 1972 1972 0739 1972 1972 1972 1972 1972 1972 1972 1972 0616 0618,0739 0880 Go Vision GoldStar GPX Greenhill Harman/Kardon Hitachi Hiteker iLo Initial Insignia Integra JBL Jensen JSI JVC jWin Kawasaki Kenwood KLH
On-Screen Display 1. Press MENU on the remote control to display the different features on your HITACHI LCD TV. 2. Use the CURSOR PAD (buttons , , and ) and highlight a different feature of the On-Screen Display menu. Press the SELECT button to select. 3. Press EXIT on the remote control to quickly exit from a menu. This part of the screen shows which selections are available.
On-Screen Display Audio Treble Bass Balance Surround Bass Boost Audio Source Internal Speakers Auto Noise Cancel Perfect Volume Loudness Language Digital Output DRC Lip Sync Timers Adjust the treble. Adjust the bass. Adjust the balance. Select Surround settings (Off, Wide, Normal) Select Bass Boost option ON or OFF. Select between three Audio Sources. Select internal or external speakers. Eliminates the noise between stations. Adjust volume in fixed setting between stations. Adjust Loudness.
Video Video Video Audio Channel Manager Select VIDEO to adjust picture settings and improve picture quality. You can independently customize each of the Video Inputs to your preference to increase viewing performance and pleasure depending upon the video program being viewed. If RESET is selected, only the selected input will reset to initial conditions. Picture Mode Use this function to choose from automatic picture settings to optimize your TV’s performance. 1.
Video Color Temperature Set this to High for cooler color with more blue, set to Medium for more natural color, set to Standard for accurate color or set to Black/White for more reddish color. Black Enhancement Use this function to enhance the shadow detail in dark scenes using the settings off, low, middle and high. NOTE: 1. If CONTRAST is selected, you are adjusting CONTRAST. The additional menu items BRIGHTNESS, COLOR, TINT, and SHARPNESS can be selected and adjusted in the same manner. 2.
Video Aspect Use this function to select the Picture Format Aspect Ratio. Video Aspect OR Auto Aspect Mode Vertical Position Move Auto Aspect Automatically adjust the Aspect Ratio depending on the input signal to fill the screen. SEL : : On 16:9 Standard1 0 Return Mode M anually select the Aspect Ratio. Vertical Position This function allows you to change the vertical position when aspect style is either 4:3 EXPANDED/ZOOM1/ZOOM2 or 16:9 ZOOM.
Audio Audio Video Audio Channel Manager Locks Select AUDIO to adjust the TV to your preference and to improve the sound quality. Timers Setup Power Swivel Move 1. 2. 3. SEL Select Press CURSOR PAD or to select menu item. Press CURSOR PAD or to adjust the function. Press EXIT to quit the MENU, or select AUDIO to return to the main menu. Audio OR NOTE: If TREBLE is selected you are adjusting treble. The additional menu items BASS and BALANCE can be selected and adjusted in the same manner.
Audio Audio Source Multi-Channel Television Sound will allow you to select STEREO (a stereo broadcast), MONO (monaural sound) used when receiving a weak stereo broadcast or SECOND AUDIO PROG (SAP) which may be a secondary language, weather report, etc. Internal Speakers This function is useful when setting up the external speakers. ON TV as Center OFF Select this feature if using the internal speakers only. Select this feature when setting up external speakers from a separate stereo system.
Channel Manager Channel Manager Video Audio Channel Manager Select CHANNEL MANAGER to set your Antenna options, run Auto Channel Scan, Check Signal Meter and Set Channel List. Locks Timers Setup Power Swivel Move Select SEL 1. Press CURSOR PAD , to highlight functions. 2. Press the SELECT button or CURSOR PAD to select. Channel Manager Signal Meter OR Auto Channel Scan Channel List Move Signal Meter Select SIGNAL METER when using an indoor or outdoor antenna.
Channel Manager Channel List This function allows you to review which channels are labeled (ID), which have been added to CHANNEL MEMORY (SCAN), which are protected by LOCK and which are your FAVORITE (FAV) CHANNELS. 1. Channel Manager Signal Meter Auto Channel Scan Channel List Move SEL Select Use the CURSOR PAD to navigate the Channel List. 2. Press the SELECT button to select ON or OFF on the SCAN and LOCK columns. 3. To select LOCK column, input the access code. (Default access code: 0000) 4.
Locks Locks Video Audio Channel Manager This function will block out the picture and sound of the selected channel or video input. Locks Timers Setup Power Swivel Move The code to enter the Locks feature is a four digit access code number. The factory preset code is 0000. Use the NUMBER buttons to enter the access code. 1. Use the CURSOR PAD , to highlight the desired function in the LOCKS menu. 2. Press the SELECT button to select.
Locks Movie Ratings Use Movie Ratings to prevent viewing of any movie that you feel may be inappropriate due to its content. Locks Change Access Code Engage Lock Movie Ratings TV Ratings Canadian Ratings (Eng) 1. Use the CURSOR PAD , to select the MOVIE RATING category that you want to block. Canadian Ratings (Frn) Region 5 Move 2. Press SELECT to block the MOVIE RATING that you have selected.
Locks TV Ratings Use TV RATINGS to prevent the viewing of any TV program that you feel may be inappropriate due to its content. Locks Change Access Code Engage Lock Movie Ratings TV Ratings Canadian Ratings (Eng) Canadian Ratings (Frn) 1. Use the CURSOR PAD , to select the TV RATING category that you want to block. 2. Region 5 Move SEL Select Press SELECT to block the TV RATING that you have selected. Locks TV Ratings 3.
Locks Canadian Ratings (Eng) Use CANADIAN RATINGS (ENG) to block any type of movie and television program in Canada that you feel might be inappropriate in its content. Locks Change Access Code Engage Lock Movie Ratings TV Ratings Canadian Ratings (Eng) 1. Use the CURSOR PAD , to select the CANADIAN RATINGS (ENG) category that you want to block. 2. On-Screen Display 3. Press SELECT to block the CANADIAN RATINGS (ENG) that you have selected.
Locks Canadian Ratings (Frn) Use CANADIAN RATINGS (FRN) to block Canadian French programs according to various program ratings that you feel might be inappropriate in its content. Locks Change Access Code Engage Lock Movie Ratings TV Ratings Canadian Ratings (Eng) 1. Use the CURSOR PAD , to select the CANADIAN RATINGS (FRN) category that you want to block. 2. 3. Press SELECT to block the CANADIAN RATINGS (FRN) that you have selected.
Locks Region 5 Use Region 5 Ratings to prevent viewing of any movie or program that you feel may be inappropriate due to its content. This feature will operate only for ATSC Digital signal. In order to set the Region 5 Ratings the ATSC Digital channel received must include Region 5 Ratings data To see if the channel has Region 5 Ratings, press the INFO key on the R/C. See fig. (1) for reference. Once the TV has received Region 5 Ratings data, the Region 5 option in the lock menu will display the data.
Timers Timers Video Audio Channel Manager Select TIMERS to set your Clock, Sleep Timer, Event Timer and Day/Night Timer. Locks Timers Setup 1. Use the CURSOR buttons or to highlight the function to be adjusted. 2. Press the SELECT button to select. Set The Clock The Clock must be adjusted before you can use the SET EVENT TIMER or DAY/NIGHT TIMER feature. Use the CURSOR PAD , , , to highlight the chosen TIME ZONE settings. 2. Press the SELECT button to select.
Timers Set Sleep Timer Select this feature to set your SLEEP TIMER from 30 minutes to 3 hours (30 minute increments). 1. Timers Press the CURSOR PAD repeatedly to set your Timer from 0:00, 0:30, 1:00, 1:30, 2:00, 2:30 and 3:00. Set The Clock 10 : 25 AM PST Set Sleep Timer 0:00 Set Day/Night Timer Not Set Set Event Timer Not Set Move SEL Select NOTE: The Sleep Timer info will show for 1 minute before the TV turns off.
Timers Set Event Timer This function will automatically operate the LCD TV viewing reservation of a program. If the clock is not set, you can not use this function and the screen at right will appear. The message on the screen will disappear after 3 seconds, then the screen automatically goes to the clock setup mode (see page 49). 1. 2. Please Set Clock First Use the CURSOR PAD , to highlight EVENT 1, EVENT 2, EVENT 3, EVENT 4 and then press the SELECT button to select.
Setup Setup Video Audio Channel Manager Select SETUP when setting your TV up for the first time. Locks Timers Setup 1. 2. Use the CURSOR PAD or to select the sub-menu of your choice. Power Swivel Move SEL Select Press the SELECT button to select. Setup Setup The Menu Options OR Set The Power Saving Set The Inputs Set The Closed Captions Select The Quick Start Option Reset The Software Move On-Screen Display Set The Menu Options Setup the Language and background of the Menu OSD.
Setup Set The Menu Background This function allows you to choose from two menu backgrounds. Setup Setup The Menu Options Set The Language : Set The Menu Background : 1. Use CURSOR PAD or to highlight SET THE MENU BACKGROUND option. Use the CURSOR PAD or to select shaded or solid. Move SEL English Shaded Return 2. Select SOLID for a black background (no picture can be seen behind menu screen), select SHADED and a light background is visible. 3.
Setup Set The Inputs Use this feature to give a name to any of the video inputs. Setup Setup The Menu Options Set The Power Saving 1. Set The Inputs Press the CURSOR PAD , to highlight the video inputs. Set The Closed Captions Select The Quick Start Option Reset The Software 2. Press the CURSOR PAD , to select your choices. Move NOTA: The inputs labeled Gray Out(Skip) or Hide(Skip) are disabled in the INPUTS selection.
Setup Set The Closed Captions Closed Captions are the dialogue, narration, and/or sound effects of a television program or home video which are displayed on the TV screen. Your local TV program guide denotes these programs as or . Setup Setup The Menu Options Set The Power Saving Set The Inputs Set The Closed Captions Select The Quick Start Option 1. Use the CURSOR PAD , , and to highlight and select the function to change. 2.
Setup Select The Quick Start Option This feature will select QUICK START UP options. Set this feature to ON to have the TV tune channels (both Analog and Digital) quickly when first turning the TV on. Set this feature to OFF to save electricity. Selecting ON for the QUICK START UP feature will activate the TV tuners circuits when the TV is in “standby mode” which is commonly referred to as “off”. This will allow you to quickly tune to channels when first turning the TV on.
Power Swivel Power Swivel Video Audio Channel Manager This feature controls the motorized stand. It allows the customer to turn the LCD Television left or right using the remote control. This feature is only available when the Table Top Stand is connected (see page 6). 1. Use the CURSOR PAD or to unlock or lock the Power Swivel. Exit the OSD menu system before controlling the motorized stand. 2. Press the CURSOR PAD to rotate the TV to the right. 3.
Equipment Care and Troubleshooting DO DO NOT Dust the screen and cabinet with a soft cloth. Do not clean your screen with strong cleaners, polishes or a chemically treated cloth. Clean the screen with a soft cloth moistened in warm water and dry with a soft cloth. A mild soap may be used if the screen is extremely dirty. Do not place rubber or vinyl products or cellophane tape on your LCD Television. Place your LCD Television away from extreme heat, humidity, and extremely dusty places.
Reception Problems IGNITION NOISE: Black spots or horizontal streaks may appear, picture may flutter or drift. Usually caused by interference from automobile ignition systems, neon lamps, electrical drills, and other electrical appliances. GHOSTS: Ghosts are caused by the television signal following two paths. One is the direct path and the other is reflected from tall buildings, hills or some other objects. Changing the direction or position of the antenna may improve reception.
Useful Info AGENCY REGULATORY INFORMATION Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Features and Specifications Features: • • • • • New 1080P Full HD LCD Display Panel New Easy-to-Use On-Screen Menu Control (3 Language) Region 5 (Downloadable V-Chip) Preprogrammed Remote Control Power Management: ON/OFF via signal detection Picture Enhancement Input Signal Identification HDMI (High Definition Multimedia Interface)(High Bandwidth Digital Content Protection V1.
Set Dimensions Useful Information 47 Inch Models (Includes Table Top Stand) Weight (lbs./kg): 74.3/33.7 42 Inch Models (Includes Table Top Stand) Weight (lbs./kg): 61.3/27.8 Rear View, Use as Reference for Wall Mount Bracket Units 47" Inches mm 42" B 281.05 C D 45-5/16 41-5/16 362.26 1151.30 Units A B C Inches 10 13-3/16 41 253.56 334.77 1041.70 mm 62 A 11-1/16 14-1/4 E 23 1050 584.82 D E 36-13/16 20-9/16 934.
Hitachi Service Hotline To locate an authorized HITACHI service facility in the continental U.S.A. and Canada, DIAL TOLL FREE 7 days a week, 24 hours a day 1-800-HITACHI (1-800-448-2244) HITACHI AMERICA, LTD. HOME ELECTRONICS DIVISION HITACHI CANADA, LTD. DIGITAL MEDIA DIVISION HITACHI has made every effort to assure you hours of trouble free operation from your unit.
Service Information When you call HITACHI SERVICE HOTLINE they will require some information related to the TV MODEL NAME and SERIAL # in order to give you the proper support. This information is located on the back of the TV and also on the RIGHT SIDE of your TV set. Please follow the next steps to find this information and then provide to SERVICE. 쐃 Look on the right side of the TV. 쐇 Locate the LABEL where it shows the information related to MODEL NAME and SERIAL #.
TELEVISOR de LCD Pantalla Plana Guía de funcionamiento para L47S601 y L42S601 INSTRUCCIONES IMPORTANTES DE SEGURIDAD............................................................ 66-67 USO POR PRIMERA VEZ ..................................................................................................... 68-85 EL CONTROL REMOTO ........................................................................................................ 86-97 MENÚ EN PANTALLA .......................................................
Instrucciones Importantes de Seguridad PUNTOS DE SEGURIDAD QUE USTED DEBE SABER SOBRE SU TELEVISOR DE LCD HITACHI Nuestra reputación se ha formado en base a la calidad, desempeño y facilidad de servicio de los televisores de LCD pantalla plana Hitachi. La seguridad está en primer lugar en nuestra mente al diseñar estas unidades. Para ayudarlo a operar estos productos en forma apropiada, esta sección ilustra datos de seguridad que serán de beneficio para usted.
Instrucciones Importantes de Seguridad Fuente de energía Este televisor de LCD esta diseñado para operar con corriente CA, 120 voltios 60 Hz. Inserte el cable de electricidad en un tomacorriente de 120 voltios a 60 Hz. La clavija se utiliza como dispositivo de desconexión y continua estando disponible.
Accesorios Uso por primera vez Asegurarse de que tiene los siguientes accesorios antes de desechar el material de empaque. 쐃 Control Remoto 쐇 Dos baterías tipo “AA” 1.5V 쐏 쐋 Cable de energía Cable para Base Giratoria Para modelos de U.S.A. : Para accessorios opcionales, visitar nuestro sitio de internet : www.hitachi.us/tv Para modelos de Canadá : Para accesorios opcionales, visitar nuestro sitio de internet : www.hitachi.ca/tv PRECAUCIÓN: 1. El montaje en el techo no es recomendable.
Cómo colocar su nuevo televisor de LCD HITACHI Asegurando a una pared 1. Use el cable metálico (dos posiciones) y amarre el televisor de LCD al tornillo sujetador en la parte posterior como se muestra abajo. Cable 2. Mantenga el televisor de LCD a 4 pulgadas (10 cm) de la pared excepto cuando lo monta usando un soporte de montaje a la pared. 3. Asegure el televisor a la pared como se muestra en la fig. A B A 42” 47” Cable (a) Sin Usar Base Giratoria B 5 in. 12 in. 12.
Cómo colocar su nuevo televisor de LCD Hitachi Uso por primera vez INSTRUCCIÓN DE COMO COLOCAR EL CABLE DE AC Y EL CABLE DE LA BASE GIRATORIA El cable de AC y el cable de la base giratoria que vienen incluidos en su nuevo Televisor de LCD necesitan ser ensamblados correctamente para evitar que se desconecte al girar el Televisor con su base. En el televisor existen 2 sujetadores de plástico localizados en la parte posterior del Televisor para sujetar el cable de AC y el cable de la base giratoria .
Cómo colocar su nuevo televisor de LCD Hitachi Uso por primera vez CONFIGURACIÓN PARA MONTAJE EN LA PARED PASO (1) : Localizar los soportes de metal de la BASE en la parte posterior del televisor. Estos metales son usados para sostener el televisor y la base; se tienen que quitar 4 tornillos de los soportes para separar el televisor y la base. 2 Sportes METAL de la BASE Quitar los 4 tornillos y luego remover los 2 soportes de metal.
Cómo colocar su nuevo televisor de LCD Hitachi Uso por primera vez VISIÓN La mejor posición para ver la imagen es en frente del televisor y de 10 a 18 pies lejos de la pantalla. Durante las horas del día, las reflexiones o reflejos de luz externa pueden aparecer en la pantalla. Si esto sucede, pueden ser usadas cortinas para reducir el reflejo o la TV puede cambiarse de lugar en el cuarto.
Cables y Conectores Uso por primera vez La mayoría de las conexiones de audio/video entre equipos puede hacerse con cables blindados de audio y video que tienen conectores RCA. Para una mejor calidad, los cables de video deben ser coaxiales blindados de 75-Ohm. Los cables pueden ser comprados en la mayoría de las tiendas que vendan productos de audio/video. Enseguida unas ilustraciones y nombres de conectores.
Guía Rápida para las Funciones del Control Remoto Uso por primera vez Además de controlar todas la funciones de su Televisor de LCD Hitachi, el nuevo control remoto es diseñado para operar diferente tipos de equipos, tales como, reproductores de DVD, CBL (Cajas de Cable), set-top-boxes, receptores de satélite, y VCRs. El control remoto debe ser programado para controlar el equipo deseado. Ver páginas 86-97 para una completa descripción de todas las opciones y como programar el Control Remoto.
Controles del Panel Lateral 햲 CONTROLES LATERALES Uso por primera vez 햶 햷 햵 햳 VISTA FRONTAL 햻 햴 햺햹 햸 햲 Botón lateral de encendido (POWER) Presionar este botón para encender ó apagar el televisor de LCD. También puede ser encendido ó apagado con el control remoto . La energía del TV solo se puede quitar desconectando la clavija.
Controles del Panel Frontal Uso por primera vez 햹 Luz Indicadora de Encendido (POWER LED) Para encender el Televisor, presionar el botón localizado en el lado derecho del Televisor de LCD. Una luz indicadora roja se encenderá en la esquina inferior derecha del marco del Televisor. El Televisor de LCD esta listo para la operación del control remoto ON/OFF. 햻 Sensor R/C 햺 Luz Indicadora Luz Indicadora Estado Operación Off OFF. Enciende Rojo OFF.
Conexiones del Panel Posterior 햷 햳 Entradas de Audio/Video 1, 2 y 3 Al usar el botón INPUTS , los CURSORES ( y ), y el botón SELECT ó el CURSOR derecho del control remoto, se puede elegir cada entrada de video. Usar las entradas de audio y video para conectar equipos externos, tales VCRs, video cámaras, reproductores de DVD, etc. (Si tiene sonido monoaural, insertar el cable de audio en la terminal izquierda de audio).
Conectando Equipos de Video Externos Uso por primera vez Las entradas en el panel LATERAL se proveen para su conveniencia permitiendole la fácil conexión de señales HDMI o DVI de un DVD, Set Top Box y Video Juego como se muestra en los siguientes ejemplos: (Al conectar señales DVI será necesario conectar la salida de audio a las entradas de audio LATERALES del Televisor) : A) Conectando señal HDMI.
Conectando Equipos de Video Externos Uso por primera vez Las terminales Laterales se proveen para su conveniencia permitiendole la fácil conexión de una Cámara de Video, un DVD, Video Juego, VCR y una Cámara Digital como se muestra en los siguientes ejemplos: CONTROLES DEL PANEL LATERAL Video Juego Equipo con Capacidad de Salida Video Compuesto Reproductor de DVD Consola de Video Juegos. R OUTPUT L Nota : Para dispositivos monoaurales favor de conectar el cable de audio en la entrada L/Mono.
Uso por primera vez R #2 Conexiones del Panel Posterior Equipo con Capacidad de Salida Digital DVI VCR #2 Equipo con Capacidad de Salida Digital HDMI HDMI OUTPUT DIGITAL OUTPUT S-VIDEO V L INPUT R AUDIO OUT HDMI a HDMI DVI a HDMI Opcional Reproductor de DVD OUTPUT Y PB/C B PR /CR L R Antena Externa ó TV por Cable TV (Cable coaxial) Opcional Y P B PR L OUTPUT R OUTPUT S-VIDEO V L R ANT IN Divisor de señal 2-Vías HDTV Set-Top Box VCR #1 NOTA: Los Cables son opcionales, excepto cuan
Consejos sobre las Conexiones del Panel Posterior Uso por primera vez • Las conexiones S-VIDEO, Y-PBPR, ó HDMI se proveen para equipos de alta fidelidad tales como DVD's, VCR's etc. que cuenten con esta opción. Use estas conexiones en lugar de una conexión de video estándar si su dispositivo cuenta con esta opción. • Si su dispositivo tiene solamente una salida de audio (monoaural), conéctelo al canal izquierdo(L/MONO) en el panel posterior de la televisión.
Conectando Equipos de Video Externos Uso por primera vez CONECTANDO UNA FUENTE DE VIDEO Y AUDIO ESTEREO A LAS ENTRADAS 1 ~ FRONTAL 1. Conecte el cable de la salida de video (VIDEO OUT) del VCR o del Reproductor de Laserdisc a la entrada de video(VIDEO/Y) como se muestra en el Panel Posterior. 2. Conecte el cable de la salida de audio derecha (AUDIO OUT R) del VCR o Reproductor de Laserdisc a la entrada de audio derecha (AUDIO/R). 3.
Conectando Equipos de Video Externos 1. Conecte el conector HDMI o el adaptador DVI/HDMI de la salida del Set Top Box HDTV o Reproductor de DVD a la entrada HDMI tal como se muestra en la parte de abajo. 2. Al usar salida DVI, conecte el cable de la salida de audio derecha(AUDIO OUT R) del Set Top Box HDTV o DVD a la entrada derecha(AUDIO IN/R) tal como se muestra en la parte de abajo. 3.
Conectando Equipos de Video Externos Uso por primera vez CONECTANDO UN EQUIPO CON SALIDA DE COMPONENTE Y DE AUDIO EN LAS ENTRADAS 2 ó 3 : Y-PBPR. 1. Conecte el cable de la salida Y del reproductor Laserdisc/Reproductor de DVD ó HDTV set top box a la entrada (Y), como se muestra en el panel posterior de la figura. 2. Conecte el cable de la salida PB/CB ó B-Y del Laserdisc/Reproductor de DVD ó HDTV set top box a la entrada PB del TV. 3.
Conectando Equipos de Video Externos Uso por primera vez CONECTANDO UN EQUIPO DE VIDEO Y AUDIO MONAURAL A LAS ENTRADAS 1, 2, 3 ó FRONTAL 1. Conectar el cable de la salida de video(VIDEO OUT) del VCR o del Reproductor de DVD a la entrada de video(VIDEO/Y) como se muestra en el Panel Posterior de la derecha. 2. Conectar el cable de la salida de audio(AUDIO OUT) de su VCR o Reproductor de DVD a la entrada (MONO)/AUDIO IN L) de su TV . 3.
El Control Remoto Además de controlar todas las funciones de su TV LCD Hitachi, el nuevo control remoto está diseñado para operar diferentes tipos de VCRs, receptores de cable, receptores satelitales, reproductores DVD, y otros equipos de audio/video con solo apretar un botón. Todas las teclas de operación básicas están agrupadas en una sola área. Para operar su TV LCD, seleccione TV presionando el botón Source del Source Select en el remoto.
Como Utilizar el Control Remoto de su TV 쐃 쐇 쐃 Botón de encendido/apagado (POWER) Presione este botón para encender o apagar el televisor cuando el remoto este en modo TV. (Ver página 86 para las instrucciones de como programar el control remoto en modo TV). 쐋 쐇 Indicadores de MODO Enciende o parpadea tres veces para mostrar el modo del control remoto. 쐋 Botón SOURCE SELECT Presione este botón para seleccionar el modo del control remoto.
Como Utilizar el Control Remoto de su TV El Control Remoto 쐄 Botón de ASPECTO (ASPECT) Presione este botón para cambiar rápidamente la relación de aspecto del formato de la imagen.
Como Utilizar el Control Remoto de su TV 쐂 Botón MENU El botón MENU desplegará el Menú en Pantalla. 쐆 Botón EXIT Este botón lo sacará de todos los menús en pantalla. 쐊 Botón de entradas (INPUTS) Cuando el control remoto está en el modo TV, presione este botón para accesar al menú de ENTRADAS. Use los CURSORES y el botón SELECT para elegir las entradas que están siendo usadas. El presionar repetidamente el botón de ENTRADAS lo llevará através de todas las opciones del menú de entradas.
Como Utilizar el Control Remoto de su TV 씉 Botón de VOLUMEN (VOL), Botón MUTE Use el botón VOL UP ( ) or VOL DOWN ( ) hasta obtener el nivel de sonido deseado. Presione el botón CANALES FAVORITOS (FAV CH) para cambiar al modo de canal favorito (FAV). Usted sabrá cuando está en el modo de Canal Favorito cuando (FAV) es desplegado y el # de canal desplegado está VERDE. Presione otra vez para regresar y sintonizar a sus canales regulares.
El Control Remoto para controlar un receptor de Cable OPERACIÓN DE LAS FUNCIONES PREGRABADAS PARA SU RECEPTOR DE CABLE. 햲 Este control remoto está diseñado para operar diferentes tipos de receptores de cable. Usted debe primero programar el control remoto para ser compatible con el sistema remoto de su receptor de cable (consulte las páginas 96-97 para ver la lista de códigos). 햳 1. Encienda su receptor de cable. 2.
El Control Remoto para controlar un STB*/Receptor Satelital OPERACIÓN DE LAS FUNCIONES PREGRABADAS PARA SU STB/RECEPTOR SATELITAL. 햲 Este control remoto está diseñado para operar diferentes tipos de STB/receptores satelitales. Usted debe primero programar el control remoto para ser compatible con el sistema remoto de su receptor de satélite (consulte las páginas 96-97 para ver la lista de códigos). 햳 1. Encienda su STB/Receptor Satelital. El Control Remoto 2.
El Control Remoto para controlar un reproductor de DVD OPERACIÓN DE LAS FUNCIONES PREGRABADAS PARA SU REPRODUCTOR DE DVD. 햲 Este control remoto está diseñado para operar diferentes tipos de reproductores de DVD. Usted debe primero programar el control remoto para ser compatible con el sistema remoto de su reproductor de DVD (consulte las páginas 96-97 para ver la lista de códigos). 햲 햳 Encienda su reproductor de DVD. 2.
El Control Remoto para controlar una VCR/PVR OPERACIÓN DE LAS FUNCIONES PREGRABADAS DE SU VCR/PVR (Videograbadora personal). 햲 Este control remoto está diseñado para operar diferentes tipos de VCRs/PVRs. Usted debe primero programar el control remoto para ser compatible con el sistema remoto de su VCR/PVR (consulte las páginas 96-97 para ver la lista de códigos). 햲 햳 1. Encienda su VCR/PVR. El Control Remoto 2.
Como utilizar el botón SOURCE SELECT ACCESO A LAS ENTRADAS Esta función opcional permite al usuario del control remoto, la configuración de su botón SOURCE SELECT para accesar una entrada específica de la TV. La configuración para esta función solamente es aplicable al modo normal del control remoto y solamente es aplicable a los modos de DVD, PVR/VCR y SAT/CBL. 1.
Códigos del Control Remoto Marca CABLE Códigos ABC ........................ 0003,0008,0011 Americast ................ 0899 Amino ...................... 1602 Bell South ............... 0899 Clearmaster ............ 0883 ClearMax ................ 0883 Coolmax ................. 0883 Digeo ...................... 1187 Director ................... 0476 General Instrument.. 0476,0810,0276,0003, 0011 GoldStar................... 0144 Hamlin ..................... 0009,0273 Hitachi .....................
Códigos del Control Remoto Marca DBS/PVR Combo Códigos Hughes Network Systems 0739 Philips Samsung 0739 Marca PVR ABS Alienware CyberPower Dell DirecTV Gateway Hewlett Packard Howard Computers HP 0739 Códigos Accurian Advent Aiwa Akai Alco Allegro Amphion Media Works AMW Apex Digital 0739 1972 1972 1972 1972 0739 1972 1972 1972 1972 1972 1972 1972 1972 0616 0618,0739 0880 Go Vision GoldStar GPX Greenhill Harman/Kardon Hitachi Hiteker iLo Initial Insignia Integra JBL Jensen JSI JVC jWin Kawasaki K
Menú en Pantalla 1. Presione MENU en el control remoto para desplegar las diferentes funciones de su TV LCD HITACHI. 2. Utilice los CURSORES (botones , , y ) para navegar por las diferentes opciones del menú. Presione el botón SELECT para seleccionar o elegir. 3. Presione EXIT en el control remoto para salir rápidamente de cualquier menú. Esta parte del menú en pantalla muestra cuales son las opciones disponibles.
Menú en Pantalla Audio Agudos Bajos Balance Surround Bass Boost Horarios Ajusta los sonidos agudos. Ajusta los sonidos bajos. Ajusta el balance. Selecciona las opciones del Sonido Surround (Off, Normal, Amplio) Activa/Desactiva la opción Bass Boost. Selecciona entre tres tipos de Audio disponibles. Bocinas Internas Selecciona las bocinas internas o bocinas externas. Auto Cancelar Ruido Elimina el ruido entre estaciones o entre canales. Volumen Perfecto Ajusta el volumen a un nivel fijo.
Video Video Video Audio Seleccione VIDEO para ajustar las opciones de la imagen y mejorar la calidad de la misma. Usted podrá configurar independientemente cada entrada de Video como prefiera, para mejorar el desempeño y lograr una visión placentera dependiendo del programa de video que se esta viendo. Si se selecciona RESTAURAR VIDEO, solo la entrada seleccionada volverá a las condiciones originales de fábrica.
Video Temperatura de Color Configure esta opción a ALTA para un color más frio (azulado), a MEDIA para un color más natural, a ESTÁNDAR para un color más preciso o a BLANCO/NEGRO para un color más rojizo . Realzar Nivel de Negro Use esta función para realzar los detalles de sombra en escenas obscuras utilizando las opciones de off, bajo, medio y alto. NOTA: 1. Si se elige CONTRASTE, usted ajustará el CONTRASTE de la imagen.
Video NOTA: 1. Para prevenir envejecimiento desigual cuando se ve una señal 4:3, desactive el Panel Lateral Obscuro. Se recomienda ver la señal 4:3 con la barra lateral gris. 2. Esta función regresa automáticamente a Off cuando se apaga y se enciende la TV. Aspecto Use esta función para seleccionar la relación de aspecto del formato de imagen. Formato Automático Automáticamente ajusta la relación de aspecto dependiendo del llenado de pantalla de la señal de entrada.
Audio Audio Video Audio Organizar Canales Censuras Seleccione el menú AUDIO para ajustar la TV a su preferencia y mejorar la calidad del sonido. Horarios Configurar Mover SEL Elegir 1. Presione los CURSORES o para elegir la opción del menú. 2. Presione los CURSORES o para ajustar la función. 3. Presione EXIT para salir del menú, o seleccione AUDIO para regresar al menú principal. Audio NOTA: Si usted selecciona Agudos, usted ajustará los tonos agudos.
Audio Tipo de Audio El sonido multicanal de Televisión (MTS-Multichannel Television Sound) le permitirá seleccionar ESTÉREO (transmisión estéreo), MONO (sonido monoaural) usado cuando se recibe una señal de transmisión estéreo débil o SAP (SECOND AUDIO PROG-Segundo Programa de Audio) que puede ser un idioma diferente, un reporte de clima, etc. Bocinas Internas Esta función es útil cuando se configuran las bocinas externas.
Organizar Canales Organizar Canales Video Audio Organizar Canales Seleccione ORGANIZAR CANALES para configurar las opciones de la antena, correr la autoprogramación de canales, verificar el medidor de señal y configurar la lista de canales. Censuras Horarios Configurar Mover SEL Elegir 1. Presione los CURSORES , para resaltar la función en el menú. 2. Presione el botón SELECT o el CURSOR para seleccionar.
Organizar Canales Organizar Canales Lista de Canales Esta función permite revisar cuales canales están etiquetados (ID), cuales están agregados a la memoria de canales, cuales están censurados y cuales son sus canales favoritos (FAV). Medidor de Señal Auto Programar Canales Lista de Canales Mover SEL Elegir 1. Use los CURSORES para navegar la Lista de Canales. 2. Presione el botón SELECT para elegir ON u OFF en las columnas Buscar y Censura. 3.
Censuras Censuras Video Audio Organizar Canales Esta función bloqueará la imagen y el sonido del canal o entrada de video seleccionada. Censuras Horarios Configurar Mover SEL Elegir El código para ingresar al menú CENSURAS es un número de acceso de cuatro dígitos. El código preestablecido de fábrica es 0000. Use los botones de NÚMERO para ingresar el código de acceso. 1. Use los CURSORES , para resaltar la función deseada en el menú CENSURAS.
Censuras Clasificación de Cine Use CLASIFICACIÓN DE CINE para prevenir ver cualquier película que usted crea inapropiada debido a su contenido. Censuras ¿Desea Cambiar Clave? Activar Bloqueo Clasificación de Cine 1. 2. Clasificación de TV Use los CURSORES , para seleccionar la categoría de CLASIFICACIÓN DE CINE que usted desee bloquear. Clasificación para Canadá (Inglés) Clasificación para Canadá (Francés) Región 5 Mover Presione SELECT para bloquear la CLASIFICACIÓN DE CINE que usted ha elegido.
Censuras Clasificación de TV Use CLASIFICACIÓN DE TV para prevenir ver cualquier programa de TV que usted crea inapropiado debido a su contenido. 1. 2. Censuras ¿Desea Cambiar Clave? Activar Bloqueo Clasificación de Cine Clasificación de TV Clasificación para Canadá (Inglés) Use los CURSORES , para seleccionar la categoría de CLASIFICACIÓN DE TV que usted desee bloquear.
Censuras Clasificación para Canadá (Inglés) Use CLASIFICACIÓN PARA CANADÁ (Inglés) para prevenir ver cualquier tipo de película o programa de televisión en Canadá que usted crea inapropiada debido a su contenido. 1. 2. Menú en Pantalla 3. Censuras ¿Desea Cambiar Clave? Activar Bloqueo Clasificación de Cine Clasificación de TV Clasificación para Canadá (Inglés) Use los CURSORES , para seleccionar la categoría de CLASIFICACIÓN PARA CANADÁ (Inglés) que usted desee bloquear.
Censuras Clasificación para Canadá (Francés) Use CLASIFICACIÓN PARA CANADÁ (Francés) para bloquear cualquier tipo de programa franco-canadiense cuyo contenido usted crea inapropiado de acuerdo a varias clasificaciones de programa. Censuras ¿Desea Cambiar Clave? Activar Bloqueo Clasificación de Cine Clasificación de TV Clasificación para Canadá (Inglés) Clasificación para Canadá (Francés) 1. 2. 3.
Censuras Región 5 Use REGIÓN 5 para prevenir ver cualquier película o programa que crea inapropiado debido a su contenido. Esta opción funciona solo para señal Digital ATSC. Para poder activar la función Región 5, el canal digital ATSC recibido debe incluir los datos de la Región 5. Para ver si el canal tiene los datos de la Región 5, presione la tecla INFO en el control remoto. Como referencia vea la fig.1.
Horarios Horarios Video Audio Organizar Canales Seleccione HORARIOS para programar su reloj y los tiempos de apagado automático y de modo Día/Noche. Censuras Horarios Configurar Mover 1. Use los CURSORES o para resaltar la función que va a ser ajustada. 2. Presione el botón SELECT para elegir. Fijar Reloj El reloj deberá ser ajustado antes para poder usar la función PROGRAMAR MODO DIA/NOCHE. Use los CURSORES , , , para resaltar y configurar el HORARIO POR ZONA. 2.
Horarios Tiempo de Auto-Apagado Seleccione esta función para configurar el TIEMPO DE AUTOAPAGADO desde 30 minutos hasta 3 horas (incrementos de 30 minutos). 1. Presione el CURSOR Horarios repetidamente para Fijar Reloj 10 : 25 AM PST Tiempo de Auto-Apagado 0:00 Programar Modo Día/Noche Sin Configurar Configurar Eventos Sin Configurar Mover SEL Elegir configurar el tiempo desde 0:00, 0:30, 1:00, 1:30, 2:00, 2:30 y 3:00.
Horarios Configurar Eventos Esta función automáticamente operará las reservaciones de programas de su televisor LCD. Si el reloj no ha sido configurado, usted no podrá usar esta función y la pantalla de la derecha aparecerá. El mensaje en la pantalla desaparecerá después de 3 segundos, entonces la pantalla automáticamente irá al modo de fijar el reloj (vea pág. 113). 1. 2. Use los CURSORES , para resaltar EVENTO 1, EVENTO 2, EVENTO 3, EVENTO 4 y luego presione el botón SELECT para elegir.
Configurar Configurar Video Audio Organizar Canales Seleccione CONFIGURAR cuando configure su TV por primera vez. Censuras Horarios Configurar 1. Use los CURSORES , , o para seleccionar el submenú de su elección. Mover SEL Elegir 2. Presione el botón SELECT para elegir. Configurar Configurar el Menú ó Ahorro de Energía Configurar Entradas Subtítulos Elegir la Opción de Inicio Rápido Restablecer el Programa Mover Configurar el Menú Configure el Lenguaje y fondo del Menú en pantalla.
Configurar Elegir Fondo de Menú Esta función le permite elegir uno de dos tipos de fondos. 1. Use los CURSORES o para resaltar ELEGIR FONDO DE MENÚ. Use los CURSORES o para seleccionar Sombreado o Sólido. 2. Seleccione SÓLIDO para un fondo negro (ninguna imagen puede ser vista detrás del menú). Seleccione SOMBREADO para mostrar un fondo semitransparente. 3. Presione EXIT para salir del menú o seleccione CONFIGURAR EL MENÚ para regresar al menú anterior.
Configurar Configurar Entradas Use esta función para dar un nombre a cualquiera de de las entradas de video 1. Configurar Configurar el Menú Ahorro de Energía Configurar Entradas Presione los CURSORES o para resaltar las entradas de video. Subtítulos Elegir la Opción de Inicio Rápido Restablecer el Programa 2. Presione los CURSORES o para seleccionar sus preferencias. Mover SEL Elegir NOTA: Las entradas en gris (Skip) ú ocultas (Hide) no están habilitadas en la selección de ENTRADAS.
Configurar Subtítulos Los Subtítulos son los diálogos, la narración, y/o los efectos de sonido de un programa de TV o video los cuales son desplegados en la pantalla de TV. Su guía de programación local identifica estos programas ó . Configurar Configurar el Menú Ahorro de Energía Configurar Entradas Subtítulos Elegir la Opción de Inicio Rápido Restablecer el Programa 1. Use los CURSORES , , y para resaltar y seleccionar la función a cambiar. Mover SEL Elegir 2.
Configurar Elegir la Opción de Inicio Rápido Esta función le permite seleccionar entre las opciones de INICIO RAPIDO. Seleccione ON para poder ver los canales (Análogos y Digitales) más rápido al encender la TV. Seleccione OFF para ahorrar electricidad. Al seleccionar ON en la función INICIO RÁPIDO se activarán los circuitos de los sintonizadores cuando la TV esta en “modo de espera” comunmente conocido “apagado”. Esto le permitirá sintonizar rapidamente los canales al encender la TV.
Girar Pantalla Girar Pantalla Video Audio Organizar Canales Esta función controla la base giratoria automática. Le permite al cliente girar la pantalla hacia la izquierda o derecha utilizando el control remoto. Esta función solo está disponible en el menú cuando la base giratoria está conectada (ver pág. 70). Censuras Horarios Configurar Girar Pantalla Mover SEL Elegir 1. Use los CURSORES o para activar o desactivar la función de Girar Pantalla.
Cuidados de su Televisión y Solución de Problemas PERMITIDO NO PERMITIDO Desempolve la pantalla y gabinete con una toalla suave. No limpie su pantalla con limpiadores fuertes, no use productos para pulir o toallas tratadas con químicos. Limpie la pantalla con una toalla ligeramente húmeda en agua tibia y seque con una toalla seca Jabón de reacción media puede ser usado si la pantalla está en extremo sucia. Coloque su Televisión de LCD lejos de calor extremo, humedad, y lugares con mucho polvo.
Problemas de Recepción RUIDO DE ENCENDIDO: Puntos negros o rayas horizontales pueden aparecer, la imagen puede variar ó moverse. Usualmente causado por interferencia de un sistema de arranque de un auto, lámparas de neón, taladros eléctricos, y otros aparatos eléctricos. IMÁGENES FANTASMAS: Imágenes fantasmas son causadas por señales de televisión siguiendo dos rutas distintas. Una es de incidencia directa y la otra es reflejada en edificios altos, montañas u otros objetos.
Información Útil INFORMACIÓN DE LA AGENCIA REGULADORA Declaración de la FCC (Federal Communications Commission) Este equipo ha sido probado y ha demostrado cumplir con las limitaciones para los dispositivos digitales Clase B, de conformidad con el Apartado 15 de las Normas de la FCC. Estos limites han sido diseñados para proporcionar una protección razonable contra las interferencias perjudiciales en una instalación residencial.
Funciones y Especificaciones Funciones: • • • • • • • • • • • • Nuevo Panel de LCD Full HD 1080P Nuevo y Fácil de Usar (3-Lenguajes) Menú en Pantalla. Censuras por Región Control Remoto Preprogramado. Ahorro de Energía: Encen./Apag. por Detección de Señal Realce de Imagen Identificación de la Señal de Entrada Compatible con HDMI (High Definition Multimedia Interface)(HighBandwidth Digital Content Protection V1.
Dimensiones Modelos de 47" (Incluyen Base) Peso (lbs./kg): 74.3/33.7 Modelos de 42" (Incluyen Base) Peso (lbs./kg): 61.3/27.8 Información Útil Centro de la Pantalla Vista Posterior, úsese como referencia para la instalación en muro. 47" 42" 126 C Unidades A B Pulgadas 11-1/16 14-1/4 45-5/16 41-5/16 362.26 1151.30 mm 281.05 Unidades A B C Pulgadas 10 13-3/16 41 mm 253.56 334.77 1041.70 D E 23 1050 584.82 D E 36-13/16 20-9/16 934.
Hitachi Servicio a Clientes Para localizar un Centro de Servicio Autorizado HITACHI en los Estados Unidos y Canadá Llame Gratis las 24 horas del día, los 7 días de la semana 1-800-HITACHI (1-800-448-2244) HITACHI AMERICA, LTD. HOME ELECTRONICS DIVISION HITACHI CANADA, LTD.
Información de Servicio Al llamar a la línea de HITACHI SERVICE HOTLINE le preguntarán cierta información relacionada con el MODELO del Televisor y el número de SERIE para poder darle el soporte adecuado. Esta información se localiza en la parte POSTERIOR y al lado DERECHO del Televisor. Favor de seguir los siguientes pasos para encontrar está información y proveerla al departamento de Servicio. 쐃 Observar el lado derecho del Televisor.
End User License Agreement for HITACHI DTV Software END USER LICENSE AGREEMENT FOR HITACHI DTV SOFTWARE IMPORTANT – READ CAREFULLY: This End User License Agreement for HITACHI DTV Software (this “Agreement”) is a legal agreement between you (“you” or “your”), in your capacity as the owner of a HITACHI brand digital television (the “DTV”), and HITACHI America, Ltd., Home Electronics Division ("HITACHI").
End User License Agreements for Operating System Software OPERATING SYSTEM LICENSE INFORMATION This HITACHI TV incorporates certain open source operating system software distributed under the GNU GENERAL PUBLIC LICENSE Version 2 and GNU LESSER GENERAL PUBLIC LICENSE Version 2.1 as defined by the Free Software Foundation, Inc. The operating system software incorporated in this Hitachi TV is shown in the table below and the applicable license(s) are detailed on the following pages of this Owner’s Guide.
End User License Agreement for Operating System Software GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright © 1989, 1991 Free Software Foundation, Inc. 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permited to copy and distribute verbatim copies of this lincense document, but changing is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it.
End User License Agreement for Operating System Software In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3.
End User License Agreement for Operating System Software TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 12.
End User License Agreement for Operating System Software GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright © 1991, 1999 Free Software Foundation, Inc. 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. [This is the ¿UVW released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.
End User License Agreement for Operating System Software straightforwardly into another language. (Hereinafter, translation included without limitation in the term "modification".) to exercise the right to control the distribution of derivative or collective works based on the Library. "Source code" for a work means the preferred form of the work for making modification to it.
End User License Agreement for Operating System Softwaree a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer's own use and reverse engineering for debugging such modifications. You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License.
End User License Agreement for Operating System Software or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number.
Appendixes Appendix A: Picture Format for Each Input Source Aspect Specifications 웎 : Un-selectable Yes : Selectable Input Auto Aspect Aspect Signal Aspect Video ID 16:9 Standard 1 16:9 Standard 2 16:9 Zoom 4:3 Standard 4:3 Expanded 4:3 Zoom 1 4:3 Zoom 2 Yes Yes Yes Yes ANT Analog Video NTSC 웎 4x3 Yes 웎 Yes ANT YC B C R 480p 웎 16x9 Yes 웎 Yes 웎 Yes 웎 웎 480i 웎 4x3 웎 웎 웎 Yes Yes Yes Yes 웎 Digital Input 1 YP B P R 1080i/720p 웎 16x9 Yes Yes Yes 웎 Yes 웎
Appendixes Appendix A: Picture Format for Each Input Source Aspect Specifications (Continuation) HDMI 1 Auto As pect As pect S ignal As pect V ideo ID 16:9 Standard 1 16:9 Standard 2 16:9 Zoom 4:3 Standard 4:3 Ex panded 4:3 Zoom 1 4:3 Zoom 2 1080p/ 1080i/720p 웎 16x9 Ye s Y es Y es 웎 Ye s 웎 웎 480p Auto ON 16x 9 Y es Initial 웎 Ye s 웎 웎 웎 웎 Letter 웎 웎 웎 Ye s Ye s Y es Initial Y es 4x3 웎 웎 웎 Ye s Y es Initial Ye s Ye s No Info Y es 웎 Ye s Y es Ye s Ye s
Index TV Ratings (Canadian - French) . . . . . . . . .47 Region 5 (Downloadable VChip) . . . . . . . .48 A Accessories, . . . . . . . . . . . . . . . . . . . . . . . . . .4 Antennas (Connecting), . . . . . . . . . . . . . . . . .8 Aspect Ratio . . . . . . . . . . . . . . . . . . . . .24, 38 Audio Bass Boost . . . . . . . . . . . . . . . . . . . . . . . .39 Audio Settings . . . . . . . . . . . . . . . . . . . . . . .39 Audio Source . . . . . . . . . . . . . . . . . . . . . . . .40 Auto Color . . . . . . . .
Notes
Notes