Installation Instructions

DOOR
SWING
DOOR
SWING
INSWINGING DOOR INSTALLATION OUTSWINGING DOOR INSTALLATION
(Switch affixed to door frame. Magnet mounted to door by front-
mounting holes. Labels facing horizontally outward.)
(Switch affixed to door stop. Magnet mounted to door
using bottom-mount holes. Labels facing downward.)
Provided by Manufacturer:
1 High Security L1.5 Switch Module
1 High Security L1.5 Magnet Module
1 Removal Tamper Magnet
2 Removal Tamper Caps
2 Spacers, 1/16"
Provided by Installer:
Power Drill
9/64" (3.5mm) Dia Drill Bit
3 x #8 x1.5" (40mm) Flathead Screws,
Self-Tapping recommended
1 x #8 x.5" (12mm) Panhead Screw,
Self-Tapping recommended
Required Tools and Components
Installation:
The High Security L1.5 should be mounted close to the latch side of the door: Up to 15” (38cm) from the doorknob/door-latch edge is recommended. Intended
for operating gaps of up to 1/4” (6mm).
Alignment and orentation of the switch & magnet modules is critical for proper operation. Center-to-center alignment of the modules must be within 1/8" (3mm).
The labeled faces of the modules must always have the same orientation.
For UL-qualified installations, only the following depicted configurations satisfy the requirements of UL634 High Security Level 1. Note the
orientation of the labeled faces and the door-swing direction.
MAGNASPHERE HIGH SECURITY L1.5 INSTALLATION INSTRUCTIONS
CAUTION: MAGNASPHERE MAGNET MODULES AND ANTI-REMOVAL MAGNETS ARE EXTREMELY POWERFUL: TAKE PRECAUTIONS TO AVOID THE MAGNETIC
ATTRACTION OF SHARP TOOLS AND TO AVOID INJURY FROM THE PINCHING FORCE BETWEEN THE MAGNET AND FERROUS METALS OR OTHER MAGNETS.
MAGNASPHERE N22 W22931 Nancys Ct. Ste 3, Waukesha, WI 53186 tel [phone] fax [phone] www.magnasphere.com
Switch Module
Removal Tamper Magnet
Removal Tamper Cap
Magnet Module
#8 Flathead
Steel Screws
#8 Panhead Steel Screw
bottom-mount
holes (this surface)
front-mount holes
(this surface)
Secure door-stop extension
available for unusually
narrow door-stops.(P/N 1524)
1/8" (3mm)
MAX OFFSET
1/4" (6mm) MAX
1/8" (3mm)
MAX OFFSET
.30" (7.6mm)
UP TO 1/4" (6mm)
OPERATING GAP
P/N: 1271
KIT: Overhead Door Rail
Mount Bracket for HS-L1.5
P/N: HS1452-L1.5-111 & -121
(w/ Modules Premounted)
KIT: Roll Up Door Bracket w/ HSL1.5-Right Side*
P/N: HS1453-L1.5-111 & -121
(w/ Modules Premounted)
KIT: Roll Up Door Bracket w/ HSL1.5-Left Side*
Installation: Flat-head screws are meant for all holes except for the large removal tamper in the switch module. Hold the switch module in position and drill one
pilot hole; drive the #8 screw in until the module is seated. Repeat for the second hole. Maintain orientation and alignment of the modules as shown. Repeat
these steps to secure the magnet module.
Wire the switch according to the schematic. Check the operation of the installed switch. The Removal Tamper circuit can be tested by withdrawing the Removal
Tamper Magnet; use a magnet or piece of steel to withdraw the Removal Tamper Magnet. Insert a Removal Tamper Cap to plug the switch's large hole. The 2nd
removal cap is a spare.
MODEL HSL1.5-121
CONTACT STATE SHOWN WITH
MAGNET IN SECURE POSITION
CLOSED
LOOP
ALARM 1
CIRCUIT
ALARM 2
CIRCUIT
TAMPER
CIRCUIT
OPEN
LOOP
CLOSED
LOOP
WHT
WHT
RED
BLU
GRN / GRN-YEL
RED
CLOSED
LOOP
CLOSED
LOOP
CLOSED
LOOP
MODEL HSL1.5-111
CONTACT STATE SHOWN WITH
MAGNET IN SECURE POSITION
ALARM 1
CIRCUIT
ALARM 2
CIRCUIT
TAMPER
CIRCUIT
WHT
WHT
RED
BLU
GRN / GRN-BLU
RED
MODEL HSL1.5-101
CONTACT STATE SHOWN WITH
MAGNET IN SECURE POSITION
CLOSED
LOOP
ALARM
CIRCUIT
TAMPER
CIRCUIT
CLOSED
LOOP
WHT
WHT
BLU
GRN / GRN-YEL
SPECIFICATIONS
PER CIRCUIT:
MAXIMUM RATINGS:
250 mA
30 VDC RESISTIVE
0.25 W
Suitable for Outdoor
or Indoor Use
Patents: 5530428, 6603378, RE39731, 8228191, & patents pending L1_5-XXX-INST REV5 16AUG2016
CLOSED
LOOP
CLOSED
LOOP
CLOSED
LOOP
MODEL HSL1.5-###†
CONTACT STATE DETERMINED
BY NOMENCLATURE: SEE KEY
ALARM 1
CIRCUIT
ALARM 2
CIRCUIT
TAMPER
CIRCUIT
WHT
WHT
RED
BLU
GRN / GRN-BLU / GRN-YEL
RED
MODEL HSL1.5-###†
VARIANTS:
HSL1.5- # # #
† KEY:
"1" is Closed-Loop
"2" is Open Loop
"0" is Not-Equipped
Alarm Circuit 1 Alarm Circuit 2
Tamper Circuit
See catalog for L-Bracket (1618), Z-Bracket (1612), 1-Inch Spacer Block (1615) and other installation accessories.