User's Guide [ [ 95-20
All trademarks, service marks, trade names, and copyrights are properties of their respective owners.
Introduction PC Card Drive series are high-performance PCI-to-PC Card adapters that support one PC Card socket, compliant with 16-bit PC Card Standard defined in 1997 PC Card Standard. 95-20 is also compliant with 32-bit CardBus Standard. PC Card Drive series provide rich features that make them the best choice for bridging between PCI and PC Card in desktop computers. The 95-20 is compliant with the 16-bit PC Card specification defined in PCMCIA Release 2.1/JEIDA 4.
Introduction Features of 95-20 * * * * * * * * Supports 16-bit(PCMCIA 2.1/JEIDA 4.1) and 32-bit(CardBus) PC Card. One rear access PC Card slot. PCI Local Bus Specification Revision 2.1 compliant. PC Card Standard 95/97 compliant. 3.3V / 5.0V operation. Intel 82365SL register compatible, ExCA compatible. Supports IRQ steering, software driver provided. Ideal for data transfer or backup between desktop PC and mobile computer.
Package Contents 95-20 contains: * * * 95-20 PCI Adapter User's Guide Setup Diskette x1 x1 x1 If there are any shortages, please contact your local dealer.
System Requirements To install and use the PC Card Drive series, your system must meets following requirements.
Software Setup The device driver software contained in the Setup Diskette is necessary for appropriate operation of the PC Card Drive series. Together with the special IRQ steering circuit embedded in the chip set, the driver software accomplishes necessary hardware configuration and IRQ routing emulation for the PC Card Drive. Included in the Setup Diskette are software drivers for various operating systems including Windows 98/98SE/ME/2000.
Software Setup * If your system is Windows XP, you can skip this chapter. Software Setup Procedure 1. Power on your computer with Windows 98/98SE/ME/ 2000. 2. Insert the Setup Diskette into the floppy disk drive of your computer. 3. Click on the Start button on the task bar to open the Start menu. 4. Click on Run, the Run dialog box appears. 5. In the text box, type in A:\Setup.exe (where A: is the floppy disk drive letter) to execute the setup program. 6.
Hardware Setup After software setup, please refer to following instructions to install your PC Card Drive hardware. 1. Before trying to install your PC Card Drive, please power off your computer and remove the power plug from the wall outlet. 2. Disassemble and remove the cover of your computer. For instructions on removing the cover of your computer, refer to the manual provided with your computer. 3.
Specification Specification of 95-20: * PCI Local Bus Specification Revision 2.1 compliant. * PCMCIA 2.1, JEIDA 4.1, and CardBus compliant. * 3.3V/5.0V operation. * Intel 82365SL register compatible, ExCA compatible. * ATA disk interface support. * Supports Hot-Swapping. Insert and remove PC Card without shutting down system. * Power saving suspend mode support.
Troubleshooting 1. If your computer is COMPAQ DeskPro EN series, you may encounter following problem: System freezes while booting up after installing PC Card Drive in the computer. Solution: Before installing, please go to Http://www.compaq.com/ to download the latest version of ROMPaq ROM Image(V2.11 or later); then follow the instructions COMPAQ provides to update the system BIOS. You can install the software and hardware of PC Card Drive without problems after BIOS update. 2.
User's Guide for 95-20(3.
Federal Communications Commission (FCC) Statement This Equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
