MyHD MyHD MyHD Macro Image Technology, Inc. HDTV PC Card User’ User’s Manual Produced by : 6th Floor, East Bldg., IT Venture Tower, 78 Garakbon-Dong, Songpa-Gu, Seoul, Korea, 138-803 TEL : 822-2142-4000 Website : www.DTVsolution.com Ma c r o I ma g e Te c h n o l o g y FAX : 822-2142-4099 E-mail : sales@mitinc.co.
MyHD FCC RF INTERFERENCE STATEMENT NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
MyHD MyHD MyHD Hardware Installation Channel Settings PC Platform Requirements -------------------------------------------------------------------- 1 MyHD Package List --------------------------------------------------------------------------- 2 Hardware Installation Overview ------------------------------------------------------------- 3 MyHD Board Diagram ------------------------------------------------------------------------- 4 Installation of MyHD board in a PC --------------------------------------
MyHD MyHD Hardware Installation PC Platform Requirements To achieve optimum performance of the MyHD Board, your PC requires a following minimum configuration. MyHD Hardware Installation MyHD MyHD Package List This package is including : - MyHD PCI Card - Quick Installation Guide CPU : Pentium-II 333MHz or faster DRAM : 64 Megabytes or more System Bus : PCI OS : Windows 98SE, Windows ME , Windows 2000, Windows XP Other Software : DirectX Media 7.
MyHD MyHD Hardware Installation Hardware installation Overview MyHD Hardware Installation MyHD MyHD board diagram VIP 1.1 Connector To install MyHD on your Windows 98SE, Windows ME, Windows 2000, or Windows XP system: Turn off your PC, install the MyHD PCI card, connect the audio jumper cable as needed, and Antenna 1 Antenna 2 connect the Remote Control Receiver to a serial port on your PC. Connect the MyHD PCI card to an external video source and display devices as desired.
MyHD MyHD Hardware Installation Installation of MyHD board in a PC Warning - Static Sensitive Components To avoid possible damage to MyHD Board and/or other system components from static discharge, always discharge your body’s static electricity prior to handling MyHD Board or other system components. Discharging can be done either by using a properly grounded anti-static wrist strap or by simply touching the chassis of a grounded (plugged-in) computer.
MyHD MyHD Hardware Installation MyHD Hardware Installation MyHD Choose your display configuration (for single-monitor displays, please go to page 9) 8. Connect the remote control receiver to 9-pin serial port. Dual monitor configuration Sound Card Monito r Graphic Card Remote Control Receiver Main Board HDTV A dual monitor configuration displays the standard Windows desktop on your PC monitor along with full-screen output from your MyHD card on a separate HDTV or VGA monitor.
MyHD MyHD Hardware Installation MyHD Hardware Installation Single Monitor Configuration MyHD Optional external hardware connections Sound Card Graphic Card You can watch and capture video from any external source (including VCR, DVD, laserdisc, etc.) by connecting them to the VGA loop through cable with external A/V connector. Simply connect the video and audio outputs from your external source to the S-Video and/or RCA input jacks.
MyHD MyHD Program Installation Installing the MyHD device driver for Windows 98/Me MyHD Program Installation MyHD Click on “Next >” if MyHD driver is searched. After your hardware installation has completed, turn on your PC and insert the installation CD. As Windows begins to boot, it will automatically open the “Add New Hardware Wizard” once it detects your addition of the MyHD card: Click on “Next >”. Choose “Search for the best driver for your Copying Files… device.
MyHD MyHD Program Installation Confirming the installation of the MyHD device driver MyHD Program Installation MyHD Setting DMA To confirm the installing MyHD in Device Manager, 1. Choose “Control Panel”/“System” /“Device Manager”. 2. Click “Sound, video and game controllers” and then confirm the category of “MDP100 Video Capture”. 1. Choose “Control Panel”/“System” /“Disk drives”. 2. Click “GENERIC IDE DISK …”. Choose; 1. “GENERIC IDE DISK … Properties” 2. “Settings” Choose; 1.
MyHD MyHD Program Installation Setting windows environment If the monitor is connected to VGA card through VGA loop through cable with external A/V connector, confirm display properties. MyHD Program Installation MyHD Installing the MyHD device driver for Windows XP After your hardware installation has completed, turn on your PC and insert the installation CD.
MyHD MyHD Program Installation MyHD Program Installation MyHD Confirming the installation of MyHD device driver Click on “Next >” to install the driver. To confirm the installation of MyHD device driver in Device Manager, 1. Choose “Control Panel”/“System” /“Device Manager” 2. Click “Sound, video and game controllers” then confirm the category of “MDP100 Video Capture”. After the installation has completed, click on “Finish”. Choose; 1. “MDP100 Video Capture Properties” 2.
MyHD MyHD Program Installation Confirming DMA Settings MyHD Program Installation MyHD Installing the MyHD Application Software To confirm the installing MyHD in Device Manager, With the installation CD still loaded in your PC, open the Windows Explorer, navigate to the APP folder on the CD, and double-click on SETUP.EXE to launch the installation, following the on-screen prompts until installation is complete.
MyHD MyHD Program Installation MyHD Program MyHD Operating MyHD The below window will be appeared when you execute the MyHD program. Installing is started. The right window is appeared after completing installing. Desired Settings are set, then click Next > Overlay window for watching TV Main control panel for the MyHD Installing of MyHD is completed. Expanded Main control panel for configuring MyHD To run the MyHD program immediately, Check the check box and click Finish.
MyHD MyHD Program MyHD Program Channel number key pad Current Display Status Audio Status Indicate the current audio configuration. 1. On digital broadcasting: Dual Mono, Center, Stereo, LCR, LRS, LCRS, LRLsRs or LCRsLs (L:left, R:right, C:center, Ls:left surround, Rs:right surround) will be displayed. 2. On analog broadcasting: Stereo, Mono, SAP will be displayed. 23 Receiving Sensitivity Indicate the sensitivity of Antenna Receiving on a current digital broadcasting channel.
MyHD MyHD Program MyHD Program File control MyHD Mode setting Mute Volume Mute audio volume. Hide Control Panel Hide control panel. Input Select Select input mode: antenna 1, antenna 2, external A/V in or file. Exit Program Exit the MyHD program. Full Screen Change Control Panel Change to mini control panel. Change to full screen mode. Configuration Change Aspect Ratio Change an aspect ratio in overlay window: 2:1, 16:9 or 4:3.
MyHD MyHD Program MyHD Program MyHD Pop-up menu Press mouse right button on MyHD application program. Pop-up menu will appear like this. antenna1 (Ctrl+1) Change input to antenna 1. Active channel As shown below, current active channel is shown. Select one of them, the channel will be changed you selected. antenna2 (Ctrl+2) Change input to antenna2 Favorite (Ctrl+M) Favorite channel mode on Video In (Ctrl+V) Channel list (Ctrl+L) Execute Channel list configure window.
MyHD MyHD Pause/Play Pause display. and, Toggled to Play. and, Select again, menu is toggled to Pause and, display play again. Stop : Stop display Channel_Up (UpArrow) : Change channel up Channel_Down (DownArrow) : Change channel down Show Main Control Panel : Shows main control panel Show Mini Control Panel : Shows mini control panel Hide Control Panel : Hide control panel. HD mode : Change to Full screen mode.
MyHD Remote Control Handset POWER Start or Exit MyHD application program. Remote Control Handset SUB-CH In Digital broadcasting. If there is sub-channel, sub-channel will change. GUIDE Display Channel Guide. (Will serve next version) Numeric Key (0 ~ 9) Change channel number directly. AUDIO Switch audio mode to stereo, mono or SAP in analog TV, switch audio channel in digital TV or DVD file play if multiple audio channels are available. Mute volume.
MyHD Channel Settings Channel Settings MyHD To set up the TV channels and display the window of “Channel Setting” 1. Select Expanded main control panel/Channel List Add/Delete Channels 2. Click right mouse button/pop up menu/channel list To add channels by manual mode: 1. Input a channel number in the channel box 2. Choose either analog or digital in the mode box To Scan Auto-Channels 3.
MyHD A/V Settings Setting Video Configuration Resolution Select full screen(HDTV) mode of MyHD video output. •1920 x 1080i is recommended if you are using a HDTV or a PC monitor because most of digital broadcast programs are sent on the air by 1920 x 1080i format. If you are watching an analog TV, please choose 720 x 480i format which is the current format of analog broadcasting programs. Aspect Ratio If you choose Auto, screen ratio will be selected automatically.
MyHD A/V Settings VGA Settings MyHD Setting the display options of an overlay window in VGA Setup. To set Audio configuration Setting Audio Configuration Audio Output 1. Cable Out (only for analog broadcasting) : To use the cable output, audio output of MyHD and a sound card must be connected(refer to Hardware Settings on the page6). If Cable Out is selected, audio output of analog broadcasting is worked by a cable even though Wave is checked. 2.
MyHD Capture Settings Capture Settings MyHD Keep Video On Top The overlay window is always displayed over other windows. Show Overlay Window Show images in an overlay window. Avi Capture Capturing a real time digital broadcasting program as an AVI file format Tape Using Separate Monitor To display HD mode in a HDTV and an overlay window in a PC Monitor simultaneously, select this function.
MyHD Capture Settings File Play Setup MyHD Options Directory Setting Setting a directory for capturing transport Stream and AVI file. Capture with Audio Disable Using this function when broadcasting program is capturing with low specifications of PC. To choose a file for replaying by a remote control Handset in a HD mode, go to “Config Panel”/”Capture File List.” Then the right window will be Displayed.
MyHD File Play Setup File Play Setup MyHD Play the next-numbered file Select this option to play automatically the divided files in the sequence according to the number of their file names. If a current file have a properly numbered file name, the nextnumbered file in the same directory will be played automatically and sequentially. If a current file have no properly numbered file name, a file with a properly numbered name like "filename_01.tp"will be searched in the same directory.
MyHD Running MyHD Running MyHD MyHD Setting Channels Storing Transport Stream into a HDD Select channels Entering numbers by keyboard or push numbers on the MyHD’s remote control Handset. Changing channels To change channels : 1. Using channel buttons in the main control panel 2. Using arrow keys in a keyboard 3.
MyHD Running MyHD To storing Transport Stream, Transport Stream Capture must be selected from “Config Panel”/”Capture Setup”/”Capture Mode.” Running MyHD MyHD Avi Capture To execute Avi capture, select “Config Panel”/”Capture Setup”/“AviCapture.” Capturing Use the record button on the remote controller or the capture button in the main control panel for storing the stream into a destined file.
MyHD Running MyHD Running MyHD Still Image Capture Tape Record Still Image Capture is capturing a still image as a file of bitmap. To execute Still Image Capture, select “Config Panel”/”Capture Setup” then check the box of “Still Image Capture.” For Tape recording; 1. Select ”Config Panel”/”Capture Setup”/”Tape” 2. Click “Capture” from pop-up menu, or 3. Use the main control panel MyHD In Detailed Options, either Field or Frame Mode can be selected.
MyHD Tape record and playback Settings Tape record and playback Settings MyHD Tape(D-VHS) record and playback Settings * It is working on Windows XP only. For settings of VCR driver 1. Two new hardware found boxes will be displayed when a D-VHS is connected to your XP machine via firewire. 2. Install software for "AV/C Tape Recorder>>Player." Do not install software for For recording 1. Excute MyHD program,then click right mouse button. 2. Select "Config Panel>>Capture Setup>>Tape" 3.
