M5S STI ICKC C User Manual 2019 V0.
TABL LE OF CON NTENT TS 1. OUTLINE E ...................................................................................... 3 1 HARDWA 1.1 ARE COMPO OSITION ............................................................... 3 2. 3. PIN DESC CRIPTION ........................................................................ 5 2 2.1. USB INTERFACE .............. . .......................................................... 5 2 2.2. GROV VE INTERFAC CE .........................................................
1 OUT 1. TLINE E M5StickC is a delicate and tiny IoT development board. It has a built-in ESP32 - PICO - D4 module, integrated 0.96 inch TFT LCD screen, IMU sensors and many more sets of hardware resources. It is covered by a PC + ABS material shell. With the fixing hole interface, M5Stick-C can be hung on any plane. Support multiple software development platforms. The overall outstanding performance will give users a quick and easy development experience. 1.
M M5StickC eq quips ESP32 with everytthing neede ed for progrramming, ev verything needed for ope eration and developme ent 4
2 PIN DESC 2. CRIPT TION 2 USB INTERF 2.1. FACE M5CAM MREA Config guration Typ pe-C type USB U interface, support U USB2.0 standarrd communiication protocol. 2 GRO 2.2. OVE INTERFACE E 4p disposed pitch of o 2.0mm M5CAMREA M erfaces, inte ernal wiring and GROVE inte V, GPIO32, GPIO33 G con nnected.
3 FUN 3. NCTIO ONAL L DESC CRIPT TION This chap pter describ bes the ESP3 32-PICO-D4 4 various mo odules and ffunctions. 3 CPU AND MEMOR 3.1. M RY ES SP32-PICO-D4 containss two low-p power Xtenssa®32-bit LX X6 MCU.
3 CRYS 3.3. STAL ES SP32-PICO--D4 integrattes a 40 MH Hz crystal osscillator. 3 RTC MANAGEMEN 3.4. NT AND LOW POWER P NSUMPT TION CON ESP32 uses adv vanced pow wer managem ment techniiques may be b switched between erent power saving mo odes. (See Ta able5). diffe Power savving mode - Active Mode: M RF chiip is operatiing. Chip ma ay receive and a transmitt a sounding g sign nal. - Modem--sleep mode e: CPU can run, r the cloc ck may be configured.
4 ELEC 4. CTRIC CAL CHAR C RACTE ERIST TICS 4 LIMIT PARA 4.1. AMETER RS Table 8: Limiting values 1. VIO to the po ower supply y pad, ReferrESP32 Tech hnical SpecifficationApp pendix IO_M MUX, as SD_CLKofPo S wer supply for VDD_SD DIO. 4 WIFII RADIO 4.2. O FREQU UENCY Table 9: Wi-Fi W RF characteristics Description Min Input frequency 2412 Output impedance - Typical Max Unit 2462 MHz 50 - Ω Declare power Output power of PA for 802.11b mode - 24.00 - dBm Output power of PA for 802.
4 LOW 4.3. W-POWE ER BLUE ETOOTH H RADIO O 4 4.3.1. rece eiver Table 10: Low-power L Bluetooth receiver r cha aracteristics 4 4.3.2.
5 QUIICK ST 5. TART T This chap pter will tea ach you how w to quick sttart with M5 5StickC. 5.11. FLAS SH FIRM MWAR RE Be efore program M5Stick kC on UIFlow w IDE, you will w need to flash the UIFlow firmare on to t the devic ce. Visit M5 5Stack offcia al website, navigate n to SUPPORT-> >DOWNLOA AD. Downlo oad the M5B Burner based on your operation o sy ystem. Unzip th he compresss file and op pen up M5B Burner.exe, select s the U UIFlow firmw ware on the list to the lefft.
Connectt your M5SttcikC to you ur computerr via Type-C cable, selecct the correspo onding COM M port, Hit Burn.( B Recommend ope eration: Erasse the flash before Burn) B 5 SETING WIFI 5.2. W If you want use u UIFlow web w IDE, you u will need to t set the M5StickC M to Wi-Fi mode e: 12 2 Long press the left side button n for 2 secon nds, to Pow wer on.
Fist pow wer on, it will enter into o Wi-Fi confiig mode. Th he display on the screen n shows the Wi-Fi acc cess point name n and Wi-Fi W configu uration page e address. 13 3 u phone or other o termin nal device to o connect th his AP.
When itt is connecte ed, use the browser on your conne ected termin nal device to o visit thiss address 19 92.168.4.1. In the Wi-Fi configuration page, ch hoose your local l Wi-Fi an nd type in th he password d. After fin nish the Wi-Fi configura ation, M5StiickC will reb boot, and au utomatically y enter intto web prog gram mode e. When the global icon n on the scre een turned Green, means m it is connected c to the UIFlow w cloud.
5 EXA 5.3. AMPLE E In n this part, a demo code e about how w to light up p an LED will be demon nstrated : Visit UIFlow Web IDE, I and en nter into th he program area, navigate to Settting, hit Setting, and ty ype in the API A key into o the dialog g box. Choo ose Stick-C, hit d hold on until it speciifies Connected. OK, and Find blo ock ‘Loop’（infinite） ）inside ‘Ev vent’, drag g it onto the e program area a and atta ach it underrneath Setup p.
FCC Statement： Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
