User's Manual

ManualsBrandsM-Labs Technologies ManualsElectronicsGPS Tracker

User

manual

Contents

1 Introduction ..............................................................................................................................2

2 ID and Tooling Design ................................................................................................................4

3 Hardware Requirements ...........................................................................................................5

3.1 Basic Hardware Requirements .........................................................................................5

3.2 Basic RF Performance Requirements................................................................................7

3.3 Certification and Safety Requirements.............................................................................9

4 Software Requirements...........................................................................................................10

4.1 Basic Software Requirements .........................................................................................10

4.2 Remote Update...............................................................................................................10

4.2.1 Auto Execute ..............................................................................................................10

4.3 Power Modes..................................................................................................................10

4.4 AT Command ..................................................................................................................11

4.5 Report.............................................................................................................................13

4.6 Reset ...............................................................................................................................13

4.6.1 Context Preservation ..................................................................................................13

4.7 Startup Banner ...............................................................................................................13

5 Test Plan ..................................................................................................................................14

5.1 Hardware Test.................................................................................................................14

5.2 Software Test ..................................................................................................................14

Summary of content (17 pages)

PAGE 1
User manual Contents 1 Introduction ..............................................................................................................................2 2 ID and Tooling Design ................................................................................................................4 3 Hardware Requirements ...........................................................................................................5 3.1 Basic Hardware Requirements .............................................
PAGE 2
1 Introduction The APOLLO series (including models CDMA/CDMA-B/CDMA-BA/CDMA-G/CDMA-BG/CDMA-BA-G) are self-contained vehicle tracking devices that combine GPS location with CDMA connectivity. Logically, the APOLLO appears to a user or a server application as a single endpoint device. It can be queried, updated and configured either through a serial connection, an over the air CDMA IP connection, or through SMS messaging.
PAGE 3
Marketing Information Item Description Potential market America Product Design Requirement Cost: Entry Level Expected sample Date QTY of Samples
PAGE 4
2 ID and Tooling Design The product appearance is shown as follows:
PAGE 5
3 Hardware Requirements 3.1 Basic Hardware Requirements Items Requirement Baseband Chipset VIA CBP8.2C/CBP8.
PAGE 6
GPIO Two GPIO pins, GP1 and GP2, are presented to the external environment on the main connector. They are general purpose, bidirectional lines capable of providing system interrupts to generate a report or drive logic levels to external devices. These lines are 2.8V logic level and are 15V tolerant. These pins default to input. GP1 is pulled down representing 0 when disconnected; GP2 is pulled up representing logical 1 when disconnected. They should be asserted to a known value if used.
PAGE 7
Timers Timers resident on the CDMA baseband chip generate periodic interrupts for power down wakeup, watchdog support, report generation and other timer related functions. Report timers are supported by related AT command and cause generation of periodic reports.
PAGE 8
Watchdog The watchdog is a dedicated part external to the main CPU. Accelerometer (Option) The optional accelerometer can be used for motion detection and driver behavior monitoring. 3.
PAGE 9
（test2：－60dBm/1.23MHz）－7.7±9.5dBm power （test3：－93.5dBm/1.23MHz）20.3±9.5dBm -42dBc/30Khzor-54dBm/1.23MHz （|Δf|:1.25MHz~1.98MHz） -50dBc/30Khzor-54dBm/1.23MHz （|Δf|: 1.98MHz~4.00MHz） <-36dBm/1kHz Conducted spurious emission （|Δf| > 4MHz, 9KHz < f < 150KHz,） <-36dBm/10kHz （|Δf| > 4MHz, 150kHz 4MHz, 30MHz 4MHz, 1GHz
PAGE 10
-42dBc/30Khzor-54dBm/1.23MHz (|Δf|:885KHz~1.98MHz) -54dBc/30Khzor-54dBm/1.23MHz 1.98MHz~4.00MHz) (|Δf|: <-36dBm/1kHz (|Δf| > 4MHz, 9KHz < f < 150KHz) <-36dBm/10kHz (|Δf| > 4MHz, 150kHz 4MHz, 30MHz 4MHz, 1GHz
PAGE 11
4 Software Requirements 4.1 Basic Software Requirements Items Requirement Air Network Interface CDMA 2000 1x 800/1900MHz; GPS 1x Data Required IP Stack Upgrade Method RUIM Ipv4/IPV6 Remote update / PC tool Optional Compatible with None-RUIM Required Remote Update Required Power Modes Required AT Command Required Report Required；23000records Driver GPIO，LED，GPS，UART GPIOs Interrupt for Door Open Detect, Ignition Status LEDs GPS Status, CDMA Status Watch Dog Required (CBP8.
PAGE 12
 Power cycle  Watchdog timeout  Reset command  CDMA phone call reset  SMS or UART power mode command  Motion detect (if detector installed and enabled) When in a power down mode, the following resources will cause interrupts that will wake the Apollo series and cause them to attempt complete the function associated with the interrupt. Simultaneous interrupts will cause sequential completion of each associated function.
PAGE 13
8. AT+IONDTE: Set driving time events 9. AT+IONFR: Restore factory defaults 10. AT+IONGF: Set geo fence borders 11. AT+IONGFH: Set geo fence around current location 12. AT+IONGPIO: GPIO Read/Write 13. AT+IONGS: GPS State report 14. AT+IONHB: Heartbeat 15. AT+IONHC: Heading Change 16. AT+IONINFx: List system information segments 17. AT+IONIP: Set target server IP address and port number 18. AT+IONIPC: IP Change report 19. AT+IONIS: Ignition State 20. AT+IONLT: LEDs’ Timing and Intensity 21.
PAGE 14
39. AT+IONUC: Update configuration files OTA 40. AT+IONVO: Virtual Odometer 41. AT+IONVTO: Virtual Trip Odometer 4.5 Report The Apollo series capture data and forms a report record with that data. This is a single data structure intended to contain all of the typically useful data on the Apollo series. Other information can be queried separately using separate AT commands. Reports are generated following specified events such as periodic timeout, speed threshold, geofence crossing, etc.
PAGE 15
5 Test Plan 5.1 Hardware Test Test Item Description Baseband Function Test • • • • • • • • • • Power Input Test Power Consumption and Current Test Heat Dissipation Test UART Stability Test GPIO Level Test LED Stability Test Drop Down Test ESD Test High/Low Temperature Test Humidity Test RF Test • • • RF Performance Test GPS Performance Test Antenna Performance Test 5.2 Software Test Test Environment Construct message Test environment 1.usb dongle and PC as message server 2.
PAGE 16
Connect to network Apollo create UDP connection with IP server IP Server server IPIPServer Download firmware from server standard serial connection Send AT command Sent message to Apollo Response shown at terminal window AT command Terminal UART Port Response to SMS server USB Send AT command Response shown at terminal window SMS Server Test Items Extension Features Test CDG2/3 Test Basic Function Test Field Test Description
PAGE 17
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.